Cisco Switching/Routing :: Connecting 3750 And 3650 Switches Together
Sep 16, 2012
I have a small network using a 24 port 3750 switch. I need to add five computers in another room and only have one Cat 6 cable running there and no room left on the 3750. I got a 3650 to put in the new room with the new computers. The problem is, whenever I plug the new switch into the 3750, it shuts down the port and gives me an err-disable. I can do a shut/no shut and re-enable the port. I searched the web and read about trunking and clusters. I'm not sure which, if either, is appropriate. I see various documentation that shows you can put one switch behind the other. But nothing tells me the configuration which will allow it.
View 9 Replies
ADVERTISEMENT
Nov 14, 2011
Server with Two NIC teamed using HP teaming tool. NIC#1 connects to SW1 and NIC#2 connects to SW2
SW1--------------------NIC_1 (SERVER) NIC_2--------------------SW2
Will the config be access-port on Sw1 & Sw2 connecting to Server.Sw1 & Sw2 are connecting to 3750 as trunk ports
View 9 Replies
View Related
Nov 13, 2011
If I have two switches in a stack can both stack able switches be connected to a core switch through gbics or just only one switch can be connected to the core and the other switch connects to the other stack able switch through an Ethernet port which uses as a gateway to the core switch?
View 3 Replies
View Related
Nov 18, 2011
If I have two stackable switches one switch uplinks to one 6509 core switch and the other connection uplinks to another 6509 core switch, and also the other stackable switch does not connect to the core switches. Because I am using hsrp and also we are not using vss then one uplink to the core is not in used only ones is so then how does creating an etherchannel between does two uplinks to both core switches benefit me in anyway such as more bandwith and using both uplinks at the same time or I'm I wrong?
View 7 Replies
View Related
Nov 14, 2011
If I have two stackable switches were only one stackable switch has two uplinks one uplink goes to one core 6509 switch and the other uplink goes to the other 6509 core switch can a Layer 3 etherchannel be used if each uplink go to a different core switch, by the way hsrp is running between both switches and also can you give an example how data will be routed from the stackable switch through the ethernetchannel to one of the core switch accross the WAN to another core switch?
View 1 Replies
View Related
Mar 14, 2013
I have created a PBR in 3650 switch to route traffic from a specific IP address to a specific next hop or IP address(Router)
ROM: Bootstrap program is C3560 boot loader
BOOTLDR: C3560 Boot Loader (C3560-HBOOT-M) Version 12.2(44)SE5, RELEASE SOFTWARE (fc1)
SW1 uptime is 6 weeks, 2 days, 16 minutes
System returned to ROM by power-on
[Code]....
View 6 Replies
View Related
Mar 11, 2012
We have a 3750 and a 3560 defined as a layer 2 switches. One gig port on each switch is trunked to layer 3 switches, which containall the VLAN definitions etc. The other gig port on the 3650 and 3750 switches are trunked together to provide an alternative path in the event of a failure.
We have added a new device to the 3750 and given it a VLAN 9, and the VLAN added to allowable VLANS on both trunk ports between the layer 3 and layer 2 devices ie:
switch port trunk allowed vlan 9,10,20,30,40,50,60,90,200,202,206,211,212,700.
From either of the 3750 or the 3560 we can ping any device on any VLAN on any switch in this group with exception ofVLAN 9. We can however ping the ip address of VLAN 9 on the layer three switches.
View 2 Replies
View Related
Aug 3, 2011
Configuring a network with Rapid Spanning Tree Protocol. There's a combination of Cisco 3650s, 2950 and 2960 switches. It is a flat Layer 2 network with a single VLAN. CLI configuration?
View 3 Replies
View Related
Nov 22, 2011
Does 3650-X IP Base support Static Load Balancing or i should upgrade to ip service SW ?
View 4 Replies
View Related
Dec 22, 2012
I have set up a scenario for a small business and have some questions about how to manage the access between the VLANs. Is there is a better / another way to do it. See the attached picture for the topology / info.
My question is:
My switches is set up with x numbers of VLANs and a routed port (no switch port) to the ASA for internet connectivity. How is the best (or only??) way to manage the access between the VLANs? Is it ACL's on the switch?
And by "managing access" I mean VLAN 50 (public WiFi) only have access to the internet, only management servers have access to management VLAN, Client VLAN only have RDP access to server VLAN and so on. Is there any way to do this in the ASA (or add another (gigabit) router to the topology)) or it the only way to have lots of ACL's on the switch itself? I have thought about "router on a stick", but then I imagine there will be a bottleneck between the switch and the ASA?
(Equipment is 2 x 3650G, ASA5505, AP1252 - see attached file).
View 3 Replies
View Related
May 18, 2013
I have a question about speed negotiation process between interfaces. I have 3650X Sw and 2960S-48port. All ports of two are GigabitEthernet, however the link between them is only 100Mb/s, Full duplex. I try to set the speed 1000 Mb/s manually in the interface then the interface never up. Its status is down/down. I must set back to speed auto. I show interface Gigabit0/24 in Sw 3650-X and figure out that there are many output drop (over 600000). I clear counter then after two days the output drop is over 70000. This link is trunk link between two switches, all ports of access SW are Gigabit and connect to PC. First, I thinks the 3650X is throttled somewhere in output direction of trunk link. But there is another trunk link (Gi0/23) to another 2960S-48port and no output drop number in this interface. This Giga 0/23 speed is 1000 Mb/s (auto speed, auto duplex)
Does any outside things impact the speed negotiation process between 2 interfaces? And output drop number may caused by abnormal speed between two Gigabit interface?
View 1 Replies
View Related
May 22, 2013
|_voip PBX___|-----|__3650___|------fiber-------------|__3650_____|------|_voipphone__| I have a case where voipphone is registered on the voippbx but peaple on both end can't hear each other . No ACL on both 3650 , no firewalls between them , distance is about 2 miles . I tried to make telnet x.x.x.x 1720 or 1719 or 1721 (h323 ports) to opposite switch -connection refused . How can test if ports are open on the 3650 ? Is it coorect If I create allowing acl and apply it on both 3650 on the interfaces connected one switch to voippbx "IN" , second switch on the interf connected to voipphone "IN" ?
View 3 Replies
View Related
Jan 5, 2011
I have got a new 48port Cisco catalyst 4948 switch, which I configured as a VTP client and connected to Cisco 3750 which is a VTP Server (this switch is on production network). I connected port g1/0/48 from 3750 to port g1/48 on 4948 through a straight cable and made both ports as trunk port (I also tried through cross cable). The problem is these two switches are not detecting. For testing I connected a PC directly to one of the port on 4948 (making that a switch port) still the LED on switch didn’t glow up. Is there any special command needs to be run on 4948 switches to activate its physical ports?
View 7 Replies
View Related
May 3, 2012
I'm introducing a Cisco 3750 switch into a Avaya environment for testing/lab. I'm concerned about any STP, VTP problems I might create as I'm going to give a address on the Management VLAN and connect it to a trunk port on a ERS5520 Avaya. I've set the switch to transparent mode and the VTP revision is set to 0. I've checked the STP priority but it doesn't give any - there is no output because it is not connected. I wouldn't be so concerned but, I'm not sure if any config has been on it before.Also, is there any way for me to see the STP prioroity without having it connected?
View 10 Replies
View Related
Nov 21, 2012
I am using a 3750 as a default gateway for multiple Vlans on a few 2960 switches. The trunk lines are configured and working and I have assigned ip addresses to each of the Vlan interfaces on the 3750. My issue is that I can only ping the ip address on the Vlan interface of the 3750 if I have a working computer plugged directly into the Vlan on the 3750. I only have 3 vlans on the 3750 that have hosts directly connected (vlans 2, 10 and 40) the other vlans ( 20 and 70) don't have any clients plugged into them on the 3750 but the hosts reside on 2 different 2960s that connect via trunk ports. How do I keep the vlan interface on the 3750 switch pingable when I don't have hosts directly connected in that vlan on the 3750? (yes, I have enabled ip routing on the 3750)
View 5 Replies
View Related
Oct 17, 2011
I have a simple design with 3750. I configured a route-map which define a next hop. I defined this route-map on a policy on a vlan interface.When I test some ping and a debug ip policy and it seems that my policy never match.Is there any mechanism that prevent the switch from using PBR? I think of CEF .
View 5 Replies
View Related
Sep 5, 2012
I have a simple design with 3750.I configured a route-map which define a next hop.I defined this route-map on a policy on a vlan interface.When I test some ping and a debug ip policy and it seems that my policy never match.Is there any mechanism that prevent the switch from using PBR?
View 10 Replies
View Related
Feb 20, 2013
Switch A connects to Swich B and C using port channel. I am going to bring down one link on each.
switch A is server farm , switch B and C are core 01 and 02 . and all are 3750 switches.
1. what will be the impact on the network in terms of spanning tree recalculation
2. what duration are we talking about until the spanning tree convergence happens?
3.I plan to shut down the link from CLI to bring down the links
View 1 Replies
View Related
Jan 21, 2013
I have a small campus network using 3750 stackable switches and a 3725 router (see diagram below). Currently the 3725 router is handling inter-vlan routing for the campus and it looks like it's not able to handle the amount of traffic we're pushing. The router CPU sometimes hits above 90% due traffic load. What I would like to accomplish is move L3 process over to the 3750 MDF stack and the IDF1 stack. I am thinking creating SVI's on both MDF stack and IDF1 stack, run HSRP between the two stacks and may be do load balance traffic between the two stack as well.
View 8 Replies
View Related
Sep 20, 2012
I have a question regarding fabric storage and cisco catalyst switch 3650.My plan is connecta a esxi server to a nexus switch and then to a san storage. I want add a new switch to have a redundant link between esxi and the storage.Can I use a cisco catalyst 3650 with a fiber conecction to connect the HBA esxi server card to 3650 sw and the SAN storage to the 3650 sw ?
View 2 Replies
View Related
Aug 6, 2012
Looking for feedback from other organizations that have large 3750 stacks. I've got one stack of (8) 3750's composed of (6) 3750G's and (2) plain 3750's. This particular stack is usually unresponsive to SNMP queries and often fails to write config when we make changes. After a couple tries it will finally go. Part of my probably here is likely the plain 3750's that always boot faster and come up as the master. I should manually set the master to one of the G's. What I'm wondering is who else has 7-9 3750's stacked and are they performing well for SNMP, telnet, etc? I've got another newer stack of 7 3750E's that I need to add one more switch to. Need to decide if I want extended downtime to break the stack up or just add the 3750X to make member 8 and hope it performs well. I have 50+ 3750 stacks working great on our campus.
View 1 Replies
View Related
Apr 30, 2013
We currently have a site with a very simple topology that uses a 3750X switch stack for a collapsed core. Everyday, the users have a conference call and experience poor voice quality.Its not bad when users call from several conference phones, but when everyone calls in on individual phones, there is choppy and almost inaudible voice quality experienced. The voice traffic flow would be as follows: Phone <-> 3750 switch <-> Voice GW We have packet captures showing that RTP packet loss is occuring from the phone to the voice gateway, but none from the voice gateway to the phones. We also have drops in the output queues that match drops on the asics. I can reset the counters and they will be clear until the call, and then they increment significantly during the call. The voice gateway and phones are non-Cisco. The switch stack has 6 switches. We are trusting the DSCP settings on the phones. All the queue drops from the phones are usually in queues 0-3, but all drops on the voice gateway is in queue 0. Below are the QoS settings; they are mostly default and we have not changed any queuing, thresholds, or buffers. Should we specify larger buffers and threshold for a designated queue and send EF traffic to that queue?
MySwitch#sh mls qos
QoS is enabled
QoS ip packet dscp rewrite is disabled
Typical Port
GigabitEthernet1/0/4
trust state: trust dscp
[code].....
View 1 Replies
View Related
Nov 14, 2011
If I have two stackable switches one that connects to the 6509 core switch and the other switch does not, do I have to uplink the switch to the other switch so that switch has route to the core switch or because the switches are daisy chain there is not need to cable one switch to to the other switch connected to core switch?
View 6 Replies
View Related
Jul 16, 2012
I want to clear following things regarding Cisco 3750 switch.
1. Can I configure Multiple DHCP pool on C3750?
2. Performance effect due to same?
3. Can I resrve IP addrese from DHCP pool for specific MAC address.
4. Can I Exempt IP address from DHCP pool ?
View 5 Replies
View Related
Nov 13, 2012
I am trying to do ios upgrade on 5 stacked 3750 switches. All the switches have different model number, so i am wondering which image file i should download. As far as i understand all the stacked switches should have the same IOS, i may be wrong. The switches have the following model numbers and SW images;
Switch Ports Model SW Version SW Image
------ ----- ----- ---------- ----------
1 28 WS-C3750G-24PS 12.2(35)SE5 C3750-IPSERVICESK9-M
* 2 28 WS-C3750G-24PS 12.2(35)SE5 C3750-IPSERVICESK9-M
3 52 WS-C3750G-48PS 12.2(35)SE5 C3750-IPSERVICESK9-M
4 30 WS-C3750E-24PD 12.2(35)SE5 C3750E-UNIVERSAL-M
5 30 WS-C3750E-24PD 12.2(35)SE5 C3750E-UNIVERSAL-M
which image file i should use as they all have different model numbers and Cisco provides different image files for each model.
View 18 Replies
View Related
Sep 23, 2010
SFP-10G-ER are not supported on Catalyst 3750-X and on other switches ....
%PHY-4-SFP_NOT_SUPPORTED: The SFP in Gi1/1/1 is not supported
Why ?When will ER be supported ?
View 19 Replies
View Related
Jan 29, 2012
I have client who has two distant offices with 3750 L3 as core (do all vlan routing for local office) and multiple L2 access switches with multiple VLAN’s connected to it. First 3750 is hub also connected to internet, second 3750 is spoke and acting as a router on stick. We have eigrp configured on both side ISP provided client 100Mbps link as a trunk with two vlan; vlan10 for voice and vlan20 for data. We assigned two small subnets to these vlans 10.15.17.0/29 and 10.15.17.9/29. Hub addresses are 10.15.17.1 and 10.15.17.9 respectively. How to force voice over VLAN10 and data via vlan20, but still do some load balancing? How to setup default route on second (router on stick) switch?
View 1 Replies
View Related
Jan 27, 2013
We have several stacks of 3750 switches where this problem is occurring. All of the switches are running IOS version 12.2(50)SE3. (Yes, I know it's old.)
We're seeing inconsistency in how the stack reports members when issuing the following commands:
sow switch
show version
show inventory
Not all members are showing up in the output of the "show version" and "show inventory" commands. For example:
HUNTI-WV-WDAC03#sh switch
H/W Current
Switch# Role Mac Address Priority Version State
----------------------------------------------------------
1 Member 108c.cff2.ea00 15 0 Ready
2 Member 8cb6.4f0a.a600 1 0 Ready
*3 Master 8cb6.4f0a.9c00 1 0 Ready
(all three switches in stack are displayed)(code)
View 1 Replies
View Related
Dec 26, 2011
I want to enable SNMP and track the status/ of the interfaces in switches.
We have Two- cat 3750 (L3 switch) and Nine-cat 2960 (L2)
How to configure the SNMP. any Links provides the required info with an example of configuring snmp will be really useful.
we have OPEN NMS, SPLUNK, MYSQL monitoring tools.
View 1 Replies
View Related
Aug 12, 2012
why the AutoQoS macro does not implement "priority-queue out" when configured on the 3750 platform running certain versions of software. The only other platform I have experience with AutoQos is on the 4500 and it enables priority queuing as expected. So what's up with autoqos on the 3750 on version 12.2(35)SE5?
When it comes to configuring QoS on campus user/phone access ports there are some important settings that can and should be considered but one can argue that enabling the priority queue is the single most impactful or important command. So I was very surprised and concerned when I didn't see priority-queue out. Cisco describes AutoQoS as a simple, quick way of deploying QoS on the LAN and it precludes you from having to learn all of the differences between hardware platforms. But is it true that this tool produces an incomplete config solution? Let me know if I am missing something.
Here is an example of what AutoQoS produces when applied to a 4507 with WS-X4648-RJ45V+E:(other interface commands are left out for simplicity)
interface GigabitEthernet5/25description XYZ
switchport mode accessauto qos voip cisco-phoneqos trust device cisco-phoneservice-policy input AutoQos-VoIP-Input-Cos-Policyservice-policy output AutoQos-VoIP-Output-Policy
policy-map AutoQos-VoIP-Output-Policy
class AutoQos-VoIP-Bearer-QosGroup
set dscp ef
[code]......
Here is an example of what AutoQoS produces when applied to a 3750 running version 12.2.(35)SE5: (no priority-queue out)
interface GigabitEthernet1/0/36
switchport access vlan 8
switchport mode access
srr-queue bandwidth share 10 10 60 20
srr-queue bandwidth shape 10 0 0 0
[code]......
View 1 Replies
View Related
Mar 26, 2012
I am wanting to etherchannel from a 3750 stack to core Layer 3 switches (also 3750) with a cable going to each core switch, I have put both core switches and the stack under a 28bit subnet mask, but I dont seem to be load balancing across both links.
View 5 Replies
View Related
Sep 22, 2012
I have 3 3750 staking switch with the following configuration:
H/W Current
Switch# Role Mac Address Priority Version State
----------------------------------------------------------
1 Member 442b.0350.9400 1 1 Ready
2 Member 442b.0357.8780 2 1 Ready
3 Master 442b.036f.a800 3 1 Ready
The new switch is installed to be wired to the master switch. the swtich 3 (* 3 Master Ready 442b.036f.a800)my question is: if you disconnect the wiring from the master stack to connect to the new switch, it is possible that the new switch change the current configuration of stacking.
-Can I just add the new switch with clean configuration without changing the current configuration ?
-How is assigned the stack number? i need the new switch be with the GI4 / x?. I can I manually by assigning ports?
-If I want to the new 3750 member witch lower prioridad, can I change priority before adding to stack?
View 2 Replies
View Related
Nov 3, 2011
I have three switches:
primary - Cisco Catalyst 3750G-24TS-24
and two SG300-28
I need to apply uplinks as follows:
3750G-24TS-24 SFP (1) -> SG300-28 (first) mini-GBIC (1)3750G-24TS-24 SFP (2) -> SG300-28 (second) mini-GBIC (1)SG300-28 (first) mini-GBIC (2) -> SG300-28 (second) mini-GBIC (2)
I would like to know, What type of mini-GBIC and SFP and cable I should use for SX Multimode?What max speed rate I will get?
View 8 Replies
View Related
