Cisco Switching/Routing :: Connecting 3750 Switch To Avaya Environment
May 3, 2012
I'm introducing a Cisco 3750 switch into a Avaya environment for testing/lab. I'm concerned about any STP, VTP problems I might create as I'm going to give a address on the Management VLAN and connect it to a trunk port on a ERS5520 Avaya. I've set the switch to transparent mode and the VTP revision is set to 0. I've checked the STP priority but it doesn't give any - there is no output because it is not connected. I wouldn't be so concerned but, I'm not sure if any config has been on it before.Also, is there any way for me to see the STP prioroity without having it connected?
View 10 Replies
ADVERTISEMENT
May 29, 2013
Since Avaya phones do not run CDP, how does the phone know which DHCP pool to pull from to get its IP address if the PC is connected to the phone.
Let's say I have a interface config like this
interface gigabitethernet1/0/1
cisco3750(config-if)#switchport mode trunk
cisco3750(config-if)#switchport access vlan 126
[code]....
And two DHCP scopes configured on the switch. What keeps the phone from pulling from the wrong scope?
View 2 Replies
View Related
Jan 5, 2011
I have got a new 48port Cisco catalyst 4948 switch, which I configured as a VTP client and connected to Cisco 3750 which is a VTP Server (this switch is on production network). I connected port g1/0/48 from 3750 to port g1/48 on 4948 through a straight cable and made both ports as trunk port (I also tried through cross cable). The problem is these two switches are not detecting. For testing I connected a PC directly to one of the port on 4948 (making that a switch port) still the LED on switch didn’t glow up. Is there any special command needs to be run on 4948 switches to activate its physical ports?
View 7 Replies
View Related
Feb 1, 2012
I am working in an enterprise LAN environment. We have about 100 switches, mostly 3560 and 3750's. This is a typical Cisco network, yet it's flat. No routing on the access layers. The core switch does do the routing. We use an third party vendor network monitoring tool, and we use Secure CRT to remote into devices.
Here's the problem. There was a device we stumbled into that had not been put into our monitoring software. It has the same IOS as our other devices. All I can say is that it's the same version and type. Each device has a management v LAN. And each device has it's own management IP. An ACL exists to prevent unauthorized SSH access into the devices, yet allows the management v LAN scope to get in.
So, here's the problem...we can't SSH into our problem mystery device, let's call it Switch X. Switch X has an IP of 10.10.100.150. Now, I can be logged into it's up link device, let's call it switch B. Switch B has an IP of 10.10.100.130. The ACL allows all devices from 10.10.100.0/24 to SSH. Our PC's at our desk are also in the same management V LAN. SSH version 2 is on the configs, and the domain names are the same on these two devices.
So, let's be clear. From my desktop, I can connect to any device on my network EXCEPT switch X. When I try to connect using SSH, port 22...it just sits there until it times out. I can do the same thing to any other switch, and connect just fine. We are using TACACS+ and RADIUS as well, and they are up and running just fine. The configs on Switch X like I said are the same for switch B, except it's IP address of course. While logged into switch B, I can do a CDP neighbor and see switch X connected via trunk link. Both sides are running dot1q encapsulation, and both are in trunk mode. I can ping switch X from switch B. When I try to SSH from B to X..I get timeout with no connection.
So, I hiked over to the building where switch X is located. I consoled into the switch. I confirmed that the ACL is the same as the ACL for switch B. It is set up to allow the management v lan inbound on the VTY 0 - 15. Yes, it's access-class (name) in on both vty 0 4 and 5 15. It also is set up for transport ssh in and transport ssh out.
I rechecked the domain name on Switch X; it was correct. I also did a crypto key and regenerated the crypto key. SSH v2 came up. Again, while in Switch X, I can do a CDP neighbor and see switch B. But I cannot SSH from switch X to Switch B, or any other devices that I tried. Now, we did find a config error with VTP; the VTP domain name was different. But VTP has nothing to do with SSH. Just to placate my co-workers, I went ahead and renamed the VTP domain name (it's running transparent mode). After I regenerated the crypto key, I saved everything of course. I then reloaded the switch. When all came back up, I still could not SSH
This is a 3560 switch, and it is trunk to a 3750.
View 13 Replies
View Related
Apr 10, 2013
Attempting to trunk an Avaya POE switch to a Cisco 3750X switch. Here's the Cisco port config: [code]
Cannot PING Avaya switch at 10.89.0.5. I have Cisco switches at .1,.2 and .3. I can PING those and access them. Any additional config needed on Cisco trunk port?
View 1 Replies
View Related
Nov 2, 2011
i have an issue to connect a trunk between cisco switch and extreme switch i have many vlans that i want to cross via a link between cisco 3750 switch and a Extreme Alpine 3800 switch
View 12 Replies
View Related
Nov 18, 2012
I have two 3750-X configured to be a stack and I am planning to re-rack these somewhere else. What I would like to know is what are the effects of having the master switch itself lose power? Does it immediately just make the member take over master (there should be no election since there are only 2 switches??) and there would be no loss of connectivity?
View 1 Replies
View Related
Nov 15, 2011
how we can configured 3560 for Avaya IP phone ? , we would link to use voice and data connect to the same port
View 1 Replies
View Related
Apr 7, 2013
We have a pair of ASA 5585X firewalls that need to connect to a pair of Avaya VSP9000 switches. The Cisco docs refer to doing spanned etherchannel with a Cat 6500 switch using VSS or a Nexus switch using VPC. Does spanned etherchannel work with non Cisco switches or is this proprietary? The etherchannel on the ASA is setup using LACP. Here's applicable configuration:
interface TenGigabitEthernet0/6
channel-group 2 mode active vss-id 1
!
interface TenGigabitEthernet0/7
channel-group 2 mode active vss-id 2
!
interface Port-channel2
port-channel span-cluster vss-load-balance
View 3 Replies
View Related
Sep 16, 2012
I have a small network using a 24 port 3750 switch. I need to add five computers in another room and only have one Cat 6 cable running there and no room left on the 3750. I got a 3650 to put in the new room with the new computers. The problem is, whenever I plug the new switch into the 3750, it shuts down the port and gives me an err-disable. I can do a shut/no shut and re-enable the port. I searched the web and read about trunking and clusters. I'm not sure which, if either, is appropriate. I see various documentation that shows you can put one switch behind the other. But nothing tells me the configuration which will allow it.
View 9 Replies
View Related
Nov 14, 2011
Server with Two NIC teamed using HP teaming tool. NIC#1 connects to SW1 and NIC#2 connects to SW2
SW1--------------------NIC_1 (SERVER) NIC_2--------------------SW2
Will the config be access-port on Sw1 & Sw2 connecting to Server.Sw1 & Sw2 are connecting to 3750 as trunk ports
View 9 Replies
View Related
Nov 13, 2011
If I have two switches in a stack can both stack able switches be connected to a core switch through gbics or just only one switch can be connected to the core and the other switch connects to the other stack able switch through an Ethernet port which uses as a gateway to the core switch?
View 3 Replies
View Related
Dec 17, 2011
I have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net.
My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20
I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2)my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to go out to the internet. I think it has to do with the routes. [code]
View 4 Replies
View Related
Jul 27, 2012
I have the task of replicating the router config on a 3825 router on a 3750 switch. Reason is we are taking out the router and replacing it with the switch to make use of the router for other functions.
Below is main part of the router config:
!
ip source-route
ip cef
!
!
multilink bundle-name authenticated
!
license udi pid CISCO3825 sn FCZxxxxxxx
!
vlan internal allocation policy ascending
[code].....
The 3750 switch I have runs C3750E-UNIVERSALK9-M, Version 12.2(55)SE3 on a LAN BASE license.
The first thing I have done is to order for a license upgrade to IP BASE which would give the support for OSPF routing.I do not see much of an issue with the Interface configs, however, I am not too sure about replicating the routing config on the switch.
My question is can I run the commands as shown for the OSPF routing on the switch? If not, can I get suggestions on how best to set this up on the switch?
View 4 Replies
View Related
Apr 16, 2012
I have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net. My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20,I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2),my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to,go out to the internet.
View 3 Replies
View Related
Mar 11, 2012
I'm running into what seems a basic ip routing config problem with a Catalyst 3750 (IP Base) switch. I have several VLANS configured on the switch with IP routing enabled, and the switch is connected to the inside interace of a new ASA 5520 as follows:
ASA5520 IP (Default gateway): 192.168.1.1Switchport Gi1/0/1 is configured as a routed port, IP address 192.168.1.3 255.255.255.0Example VLAN is VLAN 100, IP address 192.168.100.1 255.255.252.0 From the switch CLI, I can ping all VLAN addresses, as well as the ASA5520, and the client laptop I'm testing with from VLAN 100.
From the client laptop on VLAN 100, I can ping all switch interface and VLAN addresses (inter-VLAN routing is working), including 192.168.1.3, but I CANNOT ping the default gateway at 192.168.1.1.
Here is the relevant configuration information on the 3750:
!
no aaa new-model
switch 1 provision ws-c3750x-24
system mtu routing 1500
[Code]....
View 4 Replies
View Related
Nov 7, 2011
configure qos in Cisco 3750 switch.I have configured below template and applied on the vlan interface.But i am getting the hit on the access list but I am not able to get hit on the class map.
View 2 Replies
View Related
Jul 19, 2012
I had a bad expirience with Switch 3750-X. Because of an auditing security processess, my customer ran a software called "Nessus" to do a scanning of vulnerability on the network. When this software is point to switch, the process of the switch will next to 100% and reset. The software only do a listening on the ports to see what ports are opened and the switch should not reset because this. Bellow is the log os switch on the moment of test; we note that the processess 'HTTP' rise moments before the switch reset. I disable the HTTP service on switch but the problem persist. The test was made only one machine connected to switch.
View 4 Replies
View Related
Aug 12, 2012
We have three Cisco 3750 - 48port POE -LAN switches and i am trying to see if there are any issues when we stack POE and Non-POE type of switches.Aslo looking for information on the advanatage and disadvantage the stacking can provide on a Cisco 3750 48port.
View 3 Replies
View Related
Dec 12, 2010
The question is: Will a 3750 switch route Jumbo frame sizes (e.g. 9000 MTU)?
We know that we can change the System MTU to 9000, and someone on a previous thread said that we can change the Routing MTU to 9000 as well, although I couldn't figure out how to do that. However, regardless of how we configure the System MTU and Routing MTU, I don't think we're able to adjust the MTU on L3 VLAN interfaces, so if we want to actually "route" between VLANs on the switch, we're limited to 1500 MTU.
Our situation is that we have a customer connecting to our 3750 switch, and this customer wants to use Jumbo frames. The customer connects to our 3750 switch via their own VLAN, with their own L3 VLAN interface configured on the switch. The customer will point their traffic towards the L3 VLAN interface, then we want to route them onto another VLAN, via a different L3 VLAN interface, before forwarding their traffic. Because of the limitations noted above, specificially regarding the routing between these VLANs via L3 interfaces, I do not think we'll be able to support 9000 MTU frames on this 3750 switch. I think the L3 VLAN interfaces will limit us to 1500 MTU, regardless of what we configured via the global System MTU and Routing MTU settings.
View 4 Replies
View Related
Jun 8, 2007
How do you properly remove the QOS queues and configs from the switch.A was using auto qos which created a whole mess of qos configs on my running-config. I did "no mls qos" in conf term but that did not remove the queues.
View 3 Replies
View Related
Jun 21, 2012
i want to remove an access layer 3750 48 POE master switch and replace with a new 3750 switch in the stack. i want to copy the same configuration to new switch since the old switch is having POE issue and I got replacement of the malfunctioned switch. we have VTP domain is configured in the network...
View 3 Replies
View Related
Sep 11, 2012
Cisco 3750, I'm trying to reset the password but cannot communicate with my switch
View 1 Replies
View Related
Dec 9, 2012
is it generally possible to connect another switch, such as a 3750 to a port of a fabric extenders (C2232PP-10GE)?
View 1 Replies
View Related
Apr 16, 2013
I have Layer_3 " 3750-x " , so I can't do any routing on the switch , so if I need to Upgrade the IOS what is the proffered image that support hte routing , and Is it free or should I pay?
View 7 Replies
View Related
Oct 19, 2012
In Cisco 3750 facing high CPU utilization for specific period. During this period traffic response times across the switch degrades. Steps to identify interface potentially generating traffic. I have attached 'sh proc cpu history' , ' sh ip traffic', 'sh proc cpu sorted' during troubled period .
View 5 Replies
View Related
Mar 27, 2013
I have a 2 member 3750-x switch stack that was upgraded to 15.2 today via CNA. All the files were transfered and expanded correctly and it got to the step where the switches needed to be reloaded but on reload they froze.
I connected a console cable and power cycled the stack. I see the flash initialize and then the IOS image start to load. Lots of @ symbols and then nothing. It just sits there. The system light on the switches, while flashing green during the load, is now off. No light at all. But fans are running and the process will repeat itself if power cycled.
View 5 Replies
View Related
Nov 17, 2012
i have standalone 3750 switch. RPS light is green and system light is off.
3750TS#sh env all
FAN is OK
TEMPERATURE is OK
[Code].....
i have another switch with same model and ios its RPS light is off and system light is green
View 5 Replies
View Related
Apr 30, 2013
We currently have a stack of 5 x 3750 switches and i want to remove switch number 3 (it has the least number of things plugged in). What will happen to switch 4 and 5 will they be renumbered 3 and 4, and will the config automatically update this if it does?
View 2 Replies
View Related
Nov 17, 2012
I configured 3750 A switch with vlan 20 and its IP address 192.168.20.41Its default gateway was 192.168.20.3Then i configured 3750 B switch with same default gateway and vlan 20 IP 192.168.20.43My question is now when we stack it becomes single switch and now vlan 20 ip address is 192.168.20.43 thats only IP i can see.So how does stack switch choose vlan 20 IP?Does it choose highest IP address between two switches if they have same vlan 20 as in my case?Also when i go to switch 3750 b by session command and do sh ip route it does not show ip default gateway .Also it shows vlan 20 as admin down .
View 5 Replies
View Related
Aug 11, 2011
I have a doubt. In my environment I have two Switch 3750-X in stack.
My question is: How to shutdown remotely only a switch in stack?
View 23 Replies
View Related
Nov 24, 2012
I want to configure " Username & Password" on Cisco 3750 switch. I need to configure as "username xxxxxx privilege 15 password 5 xxxxxxx "
Is it possible to create password with level 5 ? I want to know about level 5 "password" & level 7 "password" ?
when i tried I am not able to configure with " password 5"
View 12 Replies
View Related
Jun 4, 2012
Our switch is very high cpu in process arp
Am debug ip arp track command the result as below
-- on this switch have interface vlan 201 ip subnet is 10.11.201.1/24
Jun 5 15:30:40.732 GMT+7: IP ARP: rcvd req src 10.11.201.217 0001.6c6b.8ab9, dst 172.27.116.73 Vlan201
Jun 5 15:30:42.150 GMT+7: IP ARP: rcvd rep src 10.11.201.217 0001.6c6b.8ab9, dst 172.27.116.4 Vlan201
Jun 5 15:30:42.150 GMT+7: IPARP_TRACK: ARP tableid(0) 10.11.201.217 Vlan201 mode(1) modified.
Jun 5 15:30:42.150 GMT+7: IP ARP: rcvd req src 10.11.201.217 0001.6c6b.8ab9, dst 172.27.116
and then am try to shutdown vlan database 201 after that the cpu process has to normal state.
How to check the root cacus?
View 1 Replies
View Related
