i have an issue to connect a trunk between cisco switch and extreme switch i have many vlans that i want to cross via a link between cisco 3750 switch and a Extreme Alpine 3800 switch
View 12 RepliesThis is regarding VLAN creation on C3750E switch.I want to create new Vlan 94 on this switch and also I want to allowed same interfaces like Vlan 95 & Vlan 96. [code]
View 7 Replies View Relatedconfigure qos in Cisco 3750 switch.I have configured below template and applied on the vlan interface.But i am getting the hit on the access list but I am not able to get hit on the class map.
View 2 Replies View RelatedI have WS-C3750-48PS-S, i wanted to implement GLBP on this switch, Is it possible to configure GLBP on this switch?
IOS : c3750-ipservicesk9-mz.122-55.SE4.bin
Part number: WS-C3750-48PS-S
[Code].....
1. How I can manage those devices, the Switch and the router? What is the BEST SOLUTION to manage this devices?
2. I want to monitor the traffic on this environment, how I can do it? How I can monitor the traffic from customer A, Customer B, and my own LAN traffic, in terms of bandwidth that has passed throught my devices? Is it possible to monitor on MY LAN, or I have to monitor from the EXTERNAL switch?
3. How I can limit the bandwidth? I was trying to configure it using access list, with policy-map, etc....and limit this on each interface. [code]
The interface does not support the specified policy configuration and/or parameter values.Assigning a policy map to the output side of an interface not supported.With I few reading, I could see that the SWITCH 3750 doesnt support this configs.My INTERNET LINK is 30 Mbps, the ports on the Switch (WS-C3750X-48P-L) are Gigabit Ethernet.How I can limit the bandwidth here? For example, How I can limit a interface to 3Mbps..I was thinking about this:
- Limit the interface to 10Mbps: speed 10
- and limit the interface with 30% of this speed: srr-queue bandwidth limit 30
Does this work for both UPLOAD and DOWNLOAD?When the packets passes that 3Mbps limitation, will they be droped?
We will be connecting Cisco 4507 with Extreme Switches. We ran into spanning-tree issues last time. Extreme does not understand spanning-tree. So what i am thinking it to prevent bpdu advertisement from 4507 to extreme switches and also prevent incoming bddu from extreme switch to 4507. I am thinking of using
spanning-tree bpdu filter
spanning-tree bpdu guard
spanning-tree root guard
We have Dell M6220 blade server that server is connected to cisco 3750 switch. I am trying to configure LACP in 3750 for two port which are connected to Dell M6220 server switch. The channel-group 2 mode active commande is not taking then its showing the error protocol mismatch and if i run show int port-channel 2 command the port channel status is showing down. The Dell server switch is on simple mode. below i have attached the required details.
Switch#show int port-channel 2
Port-channel2 is down, line protocol is down (notconnect)
Hardware is EtherChannel, address is 0000.0000.0000 (bia 0000.0000.0000)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
[code]...
I have two 3750-X configured to be a stack and I am planning to re-rack these somewhere else. What I would like to know is what are the effects of having the master switch itself lose power? Does it immediately just make the member take over master (there should be no election since there are only 2 switches??) and there would be no loss of connectivity?
View 1 Replies View RelatedWe have a customer that has a fiber rum between 2 building. They want to have 2 seperate fibers active that terminate into the same switch on each end. (redundancy).
In building A they have an extreme networks black diamond switch that does not support STP.In bulding B they have a Cisco 4507.
We will ahve to use a layer 3 routed connection due to the fact their switch in building A does not support STP.Our tech does not want to use static route becuase he does not want to setup IP SLA for the redundant connection.
Will RIPv2 work for this scenario and failover to the other fiber if needed? The hop count is the same for each fiber path..
Is it possible to trunk a SF300 switch with a 3750 switch? If so how? Whenever I turn trunking on the 3750 port I lose connection to the SF300.
View 5 Replies View RelatedI need to configure a pvlan trunk on DELL enclosure with Cisco Blade Switch, to permit pvlan and a normal Vlan.But, when I want to enter "Trunk" on private vlan mode, I can´t, because only has "host" and "prominiscous" mode. [code]
View 3 Replies View RelatedI'm trying to configure a 2940 switch to trunk. I just can't get it to work.On the interface I have added: switchport mode trunk The default is encap for this switch is dot1q, so there is no need, or ability to add/change the encap mode. Also all vlans are being allowed by default. I still can't get any port to trunk. Need to get G0/1 to trunk, have also tried to trunk f0/6 to the switch in my office. Also can't find the command to change the management VLAN. I do not use vlan 1 for management. Can I change the Mang VLAN on this switch?
View 7 Replies View RelatedI am trying to configure a trunk between the above two devices. I like to have vlan11 on ASA. Then I like to connect a host to my switch, and have it communicate with other devices in VLAN 11 or other vlans that reside on the ASA. Below is the config that I currently have.
ASA:
ciscoasa# show run interface Ethernet0/1
!
interface Ethernet0/1
[Code].....
I have two 3560G 24 port switches. Each of them connects to some 3560G or 2950 switches. Trunks between 3560G are set as 1000/full. Trunks between 3560G and 2950 are set as 100/full. show int status also shows the interface negotiation is 100/full for trunks between 3560G and 2950. The issue is I keep getting outdiscard errors in trunks between 3560G and 2950. At 2950 switches, I see Recv-errors too. I checked all the trunks traffic. They are totally not high. Only serveal mbps. Most time even lower than 1mbps.
I googled this kind of issue online. I see it could be possibly caused by high volume traffic higher than the capacity. But it appears the traffic there is not high enough to cause this kind of issue. Is there any possiblity that could cause this problem?
The below is 3560G trunk configuration for 2950 switch
interface GigabitEthernet0/10 switchport trunk encapsulation dot1q switchport trunk allowed vlan 1-122,124-4094 switchport mode trunk speed 100 duplex full srr-queue bandwidth share 10 10 60 20 queue-set 2 priority-queue out mls qos trust cos auto qos voip trust
the trunk configuration at 2950 switch: interface FastEthernet0/24 switchport trunk allowed vlan 1-122,124-4094 speed 100 duplex full
we recently aquired a managed services job and have to do a overhaul of the vlan configs and have a whole dozen WC2948G's trunk between a set of ports as well as trunk out a LAG channel setup to non cisco equipment. the deal is the lacp-channel works properly on both ends but no routing of vlans between ports and between the lag trunk are working.
theres alot of settings in the config and im planning on clearing it and starting from scratch but before i do i want to know where my problem lies.
[code]...
I had a bad expirience with Switch 3750-X. Because of an auditing security processess, my customer ran a software called "Nessus" to do a scanning of vulnerability on the network. When this software is point to switch, the process of the switch will next to 100% and reset. The software only do a listening on the ports to see what ports are opened and the switch should not reset because this. Bellow is the log os switch on the moment of test; we note that the processess 'HTTP' rise moments before the switch reset. I disable the HTTP service on switch but the problem persist. The test was made only one machine connected to switch.
View 4 Replies View RelatedWe have three Cisco 3750 - 48port POE -LAN switches and i am trying to see if there are any issues when we stack POE and Non-POE type of switches.Aslo looking for information on the advanatage and disadvantage the stacking can provide on a Cisco 3750 48port.
View 3 Replies View RelatedThe question is: Will a 3750 switch route Jumbo frame sizes (e.g. 9000 MTU)?
We know that we can change the System MTU to 9000, and someone on a previous thread said that we can change the Routing MTU to 9000 as well, although I couldn't figure out how to do that. However, regardless of how we configure the System MTU and Routing MTU, I don't think we're able to adjust the MTU on L3 VLAN interfaces, so if we want to actually "route" between VLANs on the switch, we're limited to 1500 MTU.
Our situation is that we have a customer connecting to our 3750 switch, and this customer wants to use Jumbo frames. The customer connects to our 3750 switch via their own VLAN, with their own L3 VLAN interface configured on the switch. The customer will point their traffic towards the L3 VLAN interface, then we want to route them onto another VLAN, via a different L3 VLAN interface, before forwarding their traffic. Because of the limitations noted above, specificially regarding the routing between these VLANs via L3 interfaces, I do not think we'll be able to support 9000 MTU frames on this 3750 switch. I think the L3 VLAN interfaces will limit us to 1500 MTU, regardless of what we configured via the global System MTU and Routing MTU settings.
How do you properly remove the QOS queues and configs from the switch.A was using auto qos which created a whole mess of qos configs on my running-config. I did "no mls qos" in conf term but that did not remove the queues.
View 3 Replies View Relatedi want to remove an access layer 3750 48 POE master switch and replace with a new 3750 switch in the stack. i want to copy the same configuration to new switch since the old switch is having POE issue and I got replacement of the malfunctioned switch. we have VTP domain is configured in the network...
View 3 Replies View RelatedCisco 3750, I'm trying to reset the password but cannot communicate with my switch
View 1 Replies View Relatedis it generally possible to connect another switch, such as a 3750 to a port of a fabric extenders (C2232PP-10GE)?
View 1 Replies View RelatedIn Cisco 3750 facing high CPU utilization for specific period. During this period traffic response times across the switch degrades. Steps to identify interface potentially generating traffic. I have attached 'sh proc cpu history' , ' sh ip traffic', 'sh proc cpu sorted' during troubled period .
View 5 Replies View RelatedI have a 2 member 3750-x switch stack that was upgraded to 15.2 today via CNA. All the files were transfered and expanded correctly and it got to the step where the switches needed to be reloaded but on reload they froze.
I connected a console cable and power cycled the stack. I see the flash initialize and then the IOS image start to load. Lots of @ symbols and then nothing. It just sits there. The system light on the switches, while flashing green during the load, is now off. No light at all. But fans are running and the process will repeat itself if power cycled.
i have standalone 3750 switch. RPS light is green and system light is off.
3750TS#sh env all
FAN is OK
TEMPERATURE is OK
[Code].....
i have another switch with same model and ios its RPS light is off and system light is green
We currently have a stack of 5 x 3750 switches and i want to remove switch number 3 (it has the least number of things plugged in). What will happen to switch 4 and 5 will they be renumbered 3 and 4, and will the config automatically update this if it does?
View 2 Replies View RelatedI configured 3750 A switch with vlan 20 and its IP address 192.168.20.41Its default gateway was 192.168.20.3Then i configured 3750 B switch with same default gateway and vlan 20 IP 192.168.20.43My question is now when we stack it becomes single switch and now vlan 20 ip address is 192.168.20.43 thats only IP i can see.So how does stack switch choose vlan 20 IP?Does it choose highest IP address between two switches if they have same vlan 20 as in my case?Also when i go to switch 3750 b by session command and do sh ip route it does not show ip default gateway .Also it shows vlan 20 as admin down .
View 5 Replies View RelatedI have a doubt. In my environment I have two Switch 3750-X in stack.
My question is: How to shutdown remotely only a switch in stack?
I want to configure " Username & Password" on Cisco 3750 switch. I need to configure as "username xxxxxx privilege 15 password 5 xxxxxxx "
Is it possible to create password with level 5 ? I want to know about level 5 "password" & level 7 "password" ?
when i tried I am not able to configure with " password 5"
Our switch is very high cpu in process arp
Am debug ip arp track command the result as below
-- on this switch have interface vlan 201 ip subnet is 10.11.201.1/24
Jun 5 15:30:40.732 GMT+7: IP ARP: rcvd req src 10.11.201.217 0001.6c6b.8ab9, dst 172.27.116.73 Vlan201
Jun 5 15:30:42.150 GMT+7: IP ARP: rcvd rep src 10.11.201.217 0001.6c6b.8ab9, dst 172.27.116.4 Vlan201
Jun 5 15:30:42.150 GMT+7: IPARP_TRACK: ARP tableid(0) 10.11.201.217 Vlan201 mode(1) modified.
Jun 5 15:30:42.150 GMT+7: IP ARP: rcvd req src 10.11.201.217 0001.6c6b.8ab9, dst 172.27.116
and then am try to shutdown vlan database 201 after that the cpu process has to normal state.
How to check the root cacus?
We have two 3750-x stacked switches with IP base license. We need to upgrade them to IP services license. I read some where that it is possible to install IP serivces license to only management switch and no need to purchase/install same license to other switches on the stack. But, I could not find/recall where I read it and as far as I know it was not official cisco documentation.
View 1 Replies View RelatedThere 's a Cisco IP phone that sits between a PC and the switch port. On the switch port, no MAC address is learned. However, the switch is able to detect the IP phone and deliver power to it: [code] Switch is Catalyst 3750 with IOS version 12.2(58)SE1.
View 1 Replies View RelatedI have a 3750 switch and I am trying to configure PBR (route-maps) in it.But when I try to apply the policy to a vlan interface the policy does not show in the interface.So I can not use PBR to choose my default gateway!Question: Does PBR work in a 3750 switch? Can PBR be configured in a vlan interface? There is any problem with the IOS that I do not know?
View 5 Replies View Related