Cisco :: Configure A 2940 Switch To Trunk?
Apr 24, 2012
I'm trying to configure a 2940 switch to trunk. I just can't get it to work.On the interface I have added: switchport mode trunk The default is encap for this switch is dot1q, so there is no need, or ability to add/change the encap mode. Also all vlans are being allowed by default. I still can't get any port to trunk. Need to get G0/1 to trunk, have also tried to trunk f0/6 to the switch in my office. Also can't find the command to change the management VLAN. I do not use vlan 1 for management. Can I change the Mang VLAN on this switch?
View 7 Replies
ADVERTISEMENT
Mar 5, 2012
I have a Cisco 2940 switch and a Cisco 1841 router. I want to build two different VLAN networks on the switch, which do not have to communicate one with each other, but those VLANS should communicate with the router.
I read a lot of articles, i tried to configure properly the switch and the router but i still don't get them work.
I set on the switch, the GigabitEthernet 0/1 port to Trunk port and i had to set it a native VLAN. The problem is that only from that native VLAN, i can ping the router.
View 17 Replies
View Related
Nov 2, 2011
i have an issue to connect a trunk between cisco switch and extreme switch i have many vlans that i want to cross via a link between cisco 3750 switch and a Extreme Alpine 3800 switch
View 12 Replies
View Related
Feb 12, 2012
we recently aquired a managed services job and have to do a overhaul of the vlan configs and have a whole dozen WC2948G's trunk between a set of ports as well as trunk out a LAG channel setup to non cisco equipment. the deal is the lacp-channel works properly on both ends but no routing of vlans between ports and between the lag trunk are working.
theres alot of settings in the config and im planning on clearing it and starting from scratch but before i do i want to know where my problem lies.
[code]...
View 6 Replies
View Related
Feb 2, 2012
I am trying to find out if its possible to use an existing CISCO 2940 Switch that we have here at our office as a hub? Im sure that borders on insane however, let me break down what we have currently and what I'd like to do.
We currently have a very nice setup here at work, with no problems whatsoever, however; we hired a new person and brought in some new printers and we are running out of wall jacks. Rather then run all new cabling and adding new outlets/faceplates etc... We were just gonna go purchase a simple Netgear 5 port switch/hub from the Local Comp store here in town. We found in our server room a what appears to fully functional and operational cisco 2940 8 Port Switch with a Gigabit port.
All IPs in the office are assigned via DHCP, so....on to the meat of my question -- I tried to plug this into our network and I can't get any connectivity out at all. All the ports light up green etc when I plug in the comps but they aren't pulling valid IPs.
I want to reset this thing and start from the ground up, I am not scared of going into the IOS and modifying what needs to be done...as long as I got a good enough walk through.
View 6 Replies
View Related
Mar 23, 2011
I have downloaded the 90 day ISE evaluation to a vmware platform I have it successfully authenticating local user(s) onto a Cisco 2940 device (12.1) IOS I am trying to follow a TrustSEC design guide [URL] but my LAB 2940 does not support many of the commands shown in this document What I want to try to do is be able to familiarise and demonstrate in the lab the use of ISE to control access to the network using 802.1X and or VPN access from remote vpn clients?
View 2 Replies
View Related
Mar 12, 2012
Having an issue with two Cat 2940, they have fiber 100Base-TX. Added a new Cat switch (the second on the VLAN), the existing Cat switch drops the fiber connection.
View 6 Replies
View Related
Oct 8, 2012
After reading a bit about interVLAN routing got a doubt regarding how trunking takes place at router and at switch.In case of switch we configure a port interface as trunk port and say all vlan's are allowed here but in case of router we configure sub interface as trunk saying particular vlan belongs to particular subinterface .Can't we configure only a single port interface on router just like Switch and say all vlan's are allowed here on this interface ,why to go for sub interfaces?
View 2 Replies
View Related
Dec 14, 2012
I'm using a 2504 controller. I dont have WCS.My questions are about the best way to configure a Rogue Detector AP.
In my lab environment I setup the WLC with 2 APs. One AP was in local mode, and I put the other in Rogue Detector mode.The Rogue Detector AP was connected to a trunk port on my switch. But the AP needed to get its IP address from the DHCP server running on the WLC. So I set the native vlan of the trunk port to be the vlan on which the WLC management interface resides. If the trunk port was not configured with a native vlan, the AP couldn't get an address through DHCP, nor could the AP communicate with the WLC. This makes sense because untagged traffic on the trunk port will be delivered to the native vlan. So I take it that the AP doesn't know how to tag frames.Everything looked like it was working ok.
So I connected an autonomous AP (to be used as the rogue), and associated a wireless client to it. Sure enough it showed up on the WLC as a rogue AP, but it didn't say that it was connected on the wire. From the rogue client I was able to successfully ping the management interface of the WLC.
But the WLC never actually reported the rogue AP as being connected to the wired network.So my questions are:
1. What is the correct configuration for the trunk port? Should it not be configured with a native vlan? If not, then I'm assuming the rogue detector AP will have to have a static IP address defined, and it would have to be told which vlan it's supposed to use to communicate with the WLC.
2. Assuming there is a rogue client associated with the rogue AP, how long should it reasonably take before it is determined that the rogue AP is connected to the wired network? I know this depends on if the rogue client is actually generating traffic, but in my lab environment I had the rogue client pinging the management interface of the WLC and still wasn't being picked up as an on-the-wire rogue.
View 4 Replies
View Related
Jul 19, 2012
I've been studying my inter-vlan routing , mainly in this case routing on a stick. I noticed through packet tracer that the 2960 switch doesn't allow for the '(config-if)#switchport trunk encapsulation' command, but the L3 3560 switch will.I am very concerened about this since VLANs are a main topic. What perspective will Cisco be seeing this from for the CCNA exam, I test in 12 days. I have embedded a packet tracer screen shot for more information in case I didn't word this right (which happens all the time to everyone it seems like in NW'ing now and then if not alot).
View 19 Replies
View Related
Apr 20, 2012
1- Cisco Router
Eth0/0 : Ip address 192.168.1.1 /24 == connected my laptop of 192.168.1.2
/1: Ip address : 192.168.2.1 /24 = connected cisco swith
2 - Cisco Switch
VLAN 2 Name : Sales : ip address 192.168.3. 1 = connected computer 192.168.3.2
VLAN 3 Name : Marketing : ip addres 192.168.4.1 = connected computer 192.168.4.2
So I want my laptop that connected the router Eth0/0 Interface should access both VLAN 2 and VLAN 3 computers
View 4 Replies
View Related
May 17, 2012
I have a 5508 controller with multiple SSID’s that are non-broadcasting. My goal is to get a 1142N to work in non-root bridge mode by accessing one of the existing WPA2 SSID’s.
I have a IDF that has a 3750 switch with multiple devices connected to it in 3-4 different vlans. B/C of fiber length restraints, I can’t uplink in a traditional way. So, my thought is I can connect a 1142N in non-root bridge mode and connect it to an existing WPA2 w/AES that’s being broadcasted by our 5508WLC. Connect the 1142 to 3750 and let it act as the trunk port for the devices on the switch.
View 6 Replies
View Related
May 4, 2011
Is it possible to trunk a SF300 switch with a 3750 switch? If so how? Whenever I turn trunking on the 3750 port I lose connection to the SF300.
View 5 Replies
View Related
Feb 24, 2011
Currently I have a 4510-48g HP3COM switch as a core switch for my 4 VLAN network (which I hope to send back cause it doesn't do what I wanted it to do... PBR, which is what I need to route specific VLAN's to specific interfaces on the sonicwall,.. cause sonicwall dont understand trunk or spanning tree,. meh!) This may not happen so I've dug out an old CISCO 1800 sdsl router that has 1 FE0 port and 8 other ports, FE 1-8.
The first thing I need to do is get everything to talk to each other. So I plugged the switch into it via its configured trunk port, and configured 4 sub interfaces on the router 1800 and all seemed happy as larry and working. The problem I have is I dont seem to be able to create sub interfaces on the other ports!?
[Code]...
View 6 Replies
View Related
Sep 28, 2011
I am trying to configure a trunk between the above two devices. I like to have vlan11 on ASA. Then I like to connect a host to my switch, and have it communicate with other devices in VLAN 11 or other vlans that reside on the ASA. Below is the config that I currently have.
ASA:
ciscoasa# show run interface Ethernet0/1
!
interface Ethernet0/1
[Code].....
View 5 Replies
View Related
May 12, 2013
It looks like pretty basic config, but it does not work. I have 1x 2602i autonomous mode AP, 1x C2960 switch (with inter-vlan routing prefered SDM template) and 1x 1841 router.
I trunk between Switch and Router works smoothly, but it does not work between AP and Switch or AP and Router.
Configuration looks like this:
AP2602i:
interface GigabitEthernet0
no ip address
duplex full
speed 100
[code]....
View 12 Replies
View Related
Dec 20, 2011
I need to configure a pvlan trunk on DELL enclosure with Cisco Blade Switch, to permit pvlan and a normal Vlan.But, when I want to enter "Trunk" on private vlan mode, I can´t, because only has "host" and "prominiscous" mode. [code]
View 3 Replies
View Related
Jan 20, 2013
Can I configure the Port at the ASA 5050 from Mode: access Port to trunk during the FW is running in a production area without console access ?As I know at the 5505 ist should work?
View 3 Replies
View Related
Apr 11, 2013
Is there really any reason why you wouldn't use spanning-tree portfast on a trunk port other than a trunk between two switches? We have it enabled on all ports except for the fiber trunk between two non-stacked switches and the trunk ports connected to our Astaro firewall.I'd like to enable it on the ports to the firewall unless that would cause issues.
View 9 Replies
View Related
Apr 15, 2010
I have two 3560G 24 port switches. Each of them connects to some 3560G or 2950 switches. Trunks between 3560G are set as 1000/full. Trunks between 3560G and 2950 are set as 100/full. show int status also shows the interface negotiation is 100/full for trunks between 3560G and 2950. The issue is I keep getting outdiscard errors in trunks between 3560G and 2950. At 2950 switches, I see Recv-errors too. I checked all the trunks traffic. They are totally not high. Only serveal mbps. Most time even lower than 1mbps.
I googled this kind of issue online. I see it could be possibly caused by high volume traffic higher than the capacity. But it appears the traffic there is not high enough to cause this kind of issue. Is there any possiblity that could cause this problem?
The below is 3560G trunk configuration for 2950 switch
interface GigabitEthernet0/10 switchport trunk encapsulation dot1q switchport trunk allowed vlan 1-122,124-4094 switchport mode trunk speed 100 duplex full srr-queue bandwidth share 10 10 60 20 queue-set 2 priority-queue out mls qos trust cos auto qos voip trust
the trunk configuration at 2950 switch: interface FastEthernet0/24 switchport trunk allowed vlan 1-122,124-4094 speed 100 duplex full
View 16 Replies
View Related
Jan 16, 2013
This is regarding VLAN creation on C3750E switch.I want to create new Vlan 94 on this switch and also I want to allowed same interfaces like Vlan 95 & Vlan 96. [code]
View 7 Replies
View Related
Feb 27, 2012
What is network port ? I want to configure a trunk port as network port, so that the trunk port becomes the network port for all the VLAN associated to the port.
View 18 Replies
View Related
Aug 2, 2012
I have a Cisco Catalyst 2940 switch, eight ports. Ports 1-4 are connected to a media converter A. Ports 5-6 and 7-8 goes to two separate servers, B and C. Let's say I want traffic from B->5->1->A then through some equipment (which just pushes the data) and back through A->2->6->C without the data just recognizing a shorter path B->5->6->C and thereby skipping the equipment in between. Is this possible without a router? Ridiculous set-up? Yes, though the switch is the only means I have to connect to the media converter in this case.
View 5 Replies
View Related
Mar 3, 2012
I have this strange problem with my Macbook pro, when I connect it to my cisco 2940 8 port switch then I can reach my ISP (websites eg. google.com) in like 2 minuttes, then something is happening on my router, because suddenly I can´t reach my ISP
This is what I have found out so far:
1. when I lose connection to my ISP then I can only ping internal ip addresses eg. another computer in my network
2. if I renew my ip address on the Macbook then it works again in 2 minutts, then the same happens again. This is my network setup:
Router -> Switch 1 -> Switch 2
I also know that it is not the Macbook, because it have got a new motherboard, and it have been reinstalled
also if I use the Macbook on a other network then it works fine.
All my other computers ( windows and linux ) works fine, no problems.
To me it looks like it is a Nat and/or DNS problem, but I can´t fine out what it is.
View 7 Replies
View Related
Jun 28, 2012
I have a problem, i would like todo MACSEC betwwen two switches cisco catalyst 3560-x but I know that for this operation i needed ACS server 5.1 is it possible to encryp dataflow without ACS server and if you have the configuration
View 7 Replies
View Related
Jun 6, 2013
I have two switches (sanitized configs attached) and I am trying to bond int gi0/1 and gi0/2 between the two. Then I need int gi0/3 back to the main LAN switches. These are new Vlans created 982 and 983 for these switches. Question #1: do the configurations look correct? I haven't placed any laptops on the interfaces to test interconnectivity yet but I am wondering if it will work with no default routes.
The admin team needs these switches at location A for setup then they will be moved to Location B. The only thing that sucks for me is that the network admin before me created gateway interfaces for all the local Vlans on a main router as sub interfaces. For example, for these two subnets, I need to create subinterfaces below (at location A), which is why a gave the Vlan on the switches, ip addresses.
interface GigabitEthernet0/0.982
encapsulation dot1Q 982
ip address 10.98.2.1 255.255.255.0
ip flow ingress
no cdp enable
service-policy input mark-mplsqos-in
interface GigabitEthernet0/0.983
encapsulation dot1Q 983
ip address 10.98.3.1 255.255.255.0
ip flow ingress
no cdp enable
service-policy input mark-mplsqos-in
When I move the subnet to location B, I will also move the gateway. These two switches will be used mainly for a VMWare and HyperVisor environment so Vlan 982 is for VMA network and Vlan 983 is for management. The admin tells me the software needs to tag the packets, I am not sure if I care as the switches should handle that also.
View 1 Replies
View Related
Nov 5, 2011
I connect switch with IPcop my internet are slow but I connect direct Ipcop with 1 PC internet is process fast normal
View 1 Replies
View Related
Jul 25, 2011
i want to configure my switch as a gateway
View 2 Replies
View Related
Apr 9, 2012
How to config SVI on Cisco 6509 switches??
View 1 Replies
View Related
Feb 12, 2013
I would like to configure a switch to act like a Hub. I know about the mirroring port configuration, but unfortunately is not enough for me. Is it possible to do that with the switch that I have (i.e. SG 200-08) ? If not do you know a switch on which I can configure it like a hub (that mean no flow control between physical ports).
View 1 Replies
View Related
Jul 31, 2011
how to configure QoS on Cisco 4948. I have three VLans in my network. First is video traffic second is the voice traffic and third is the data traffic . I need to set the priority in QoS in the following way
i.e. Video traffic - 1st pref
Voice traffic - 2nd pref
Data traffic - 3rd pref
how to configure for this requirement.
View 3 Replies
View Related
Feb 5, 2012
I only have access to 1 pc and 1 router/switch.I know how to make the pc a tftp server with a tftp server program, which i can then upload my router config to.I now do not have access to that tftp program anymore and am trying to find another way to save the router config(not to nvram on the actual router but to my local pc).I have heard of peopel doing it with putty saving the log onto a file but how would you load that log??
View 1 Replies
View Related
Jan 7, 2012
I want write comment for command when i config switch .i want when use show running display comment .
View 1 Replies
View Related
