I have a problem, i would like todo MACSEC betwwen two switches cisco catalyst 3560-x but I know that for this operation i needed ACS server 5.1 is it possible to encryp dataflow without ACS server and if you have the configuration
View 7 RepliesTo use MACSec between 2 Catalyst 3560-X on both sides with a provider network between that is configured for IEEE 802.1Q Tunneling ?
Since MACSec uses 0x88e5 Frames and the Cisco SAP protocol uses 802.1x for negotiation, can that be working ? (I haven't success)
Which IOS version of 3560-X switch support NAC-L2-IP ?
View 1 Replies View RelatedI am using 3560 switch senerio is that we have dhcp server on and I want that switch filter mac on whole switch ports not on a some port. Switch only give IP to the mac whcih is in mac table of switch/particular which we enter manually.I have read chapter 62 of port security but it doesnot fulfill my requirements.I am also using 3com 5500Ei switch in which we dont have to bind a mac on every port, we just enter a mac in the switch and it filter itself by using simple commands.DHCP server is not in our hands, we cant do any things there.
View 1 Replies View Relatedconfigure QoS on 3560 switch i have taken the template from cisco configuration guide since we have different QoS configuration on each model.
below is the configuration :
configure terminal
mls qos
end
mls qos map cos-dscp 0 8 16 26 32 46 48 56
no mls qos srr-queue input cos-map mls qos srr-queue input cos-map queue 1 threshold 2 1 mls qos srr-queue input cos-map queue 1 threshold 3 0
[code]....
Currently all the cisco phones are connected to this switch and configuration with only one vlan that is voice vlan .
1) what is the outcome of this configuration , i mean, what will be the expected output ? end of the day we need to prioritize the voice traffic but why other commands including threshold and buffers are mentioned with respectives queues , if I need to explain that what am i expecting out of this configuration ?
2) this is LAN QoS which i understood but again , do i need to configure policy-map along with class-map which is MQC on this switch ?
3) i have edge router where i have MQC already configured but confusion with this switch which is working as a Access switch .
4) I referred the cisco QoS document for the respetive model whereas we have policy-map configured on the same switch with class-map .
My understanding is if we have configured the LAN QoS , and mapped the CoS value with DSCP , we need not to have MQC.
I want to configure Cisco 3560 SWITCH with IP cameras. I need to configure the ports connected to Camers. IP addresses to the Cameras has been assigned.
View 1 Replies View RelatedWhen will the WS-4500X-32 support the TrustSec MACsec Encryption ?
View 1 Replies View Relatedwe are using 2960 cisco switch asn we are trying to configure port security.we are able to configure MAC base port security, but unbale to configure IP base port security.can any one guide us can do IP base port security like MAC port security. if not which switch will support IP and Mac base port security.
View 6 Replies View RelatedI have a 2 cisco switches that are at different sites one is a Cisco CAT4500 and other 3560. The connection between the switches is a layer 2 fibre link. CAT4500 and 3560 both have VLAN interface ip addresses in order for me to connect to the switches.
I have PC A connected to CAT4500 and PC B connecting to 3560. All these devices are the same VLAN and in the same subnet. I do have trunk links all the way though allowing this vlan as we run vlans. From PC A, I can ping CAT4500, 3560 and even PC B. This tells me everything is fine regarding Layer 2 & 3.
As soon as I move PC B and connect it to the other switch CAT4500 or move the other PC vice versa (this happens in both directions). Both switches learn that the mac address has moved locations and updates its mac address table accordingly. So when I do a show mac address table and show arp, everything has learned and moved fine. However when I try to ping any other device from PC B I cannot. So the 3560 switch PC B was originally connected to, I can no longer ping, the switch cannot see the pc also. It is as if PC B has not learned anything from the switch and cannot respond or reply to any icmp. I have tried this with different end devices, same thing. I am now thinking it has something to do with the switch.
how to configure FWSM module in cisco core switch 6500
View 2 Replies View Relatedi have an issue to connect a trunk between cisco switch and extreme switch i have many vlans that i want to cross via a link between cisco 3750 switch and a Extreme Alpine 3800 switch
View 12 Replies View RelatedService Provider will config a Q-n-Q connection between (2) datacenters. I would like the traffic encrypted over that connection.
Could I use a 3750X at each location and configure Macsec?
how can i upload IOS in Switch when it is in ROMMAN Mode , its show IOS in flash but may pe Corrupt, show how can i put New ios in Switch 3560.
View 1 Replies View Relatedcan i use normal two L3 Switch(3560) for BGP Multihoming with 2 different isp
View 4 Replies View RelatedHow to configure SLA monitoring in 3560 switch. I have 2 DSL links terminating in switch and want to do WAN failover. I know how to do in ASA and router. I found IP SLA and track commands on switch but don't know exactly how to use them.
View 2 Replies View RelatedI am using Cisco 3560 POE -WS-C3560CG-8PC-S- switch for my AP's. The current IOS i got on this switch don't allow me to use web console. when i am click on webconsole i am getting attached. what is the best way of removing and installing new IOS.
View 5 Replies View RelatedI am looking for The latest IOS Available for cisco 3560 Series Switch, User guide for the same And All Supported features specification Guide.
View 7 Replies View RelatedI am having LMS 2.5 and nearly 50 cisco 3560 in my network. And I want to configure rcp. How can I do it.
View 1 Replies View Relatedwhy getting temperature event in 3560 switch, and we checked the Network room Temp it's normal around (22).
View 8 Replies View RelatedI have issue with 3560 switch QoS configuration . I checked in cisco site about mentioned model QoS configuration.once we mark the frame and map the CoS to DSCP and once it enters into switch and it processes according to LAN QoS configured on interface
we have configured both the commands shape and share.
once it leaves the switch and enters into Edge router and if we do not have configured QoS in router which is normally MQC , how does it process each packet ?Do we need to have end to end QoS configured in LAN ?
We are facing a weird problem of high CPU utilization on 3560 switch. Even without connecting a single PC to switch, CPU utilization is showing 22 %. Any particular reason for this? Can configuration affect the CPU utilization even though there is no PC connected?
View 5 Replies View Relatedpxe server ip address is 10.10.10.20 which is connected to switch port fa0/9 and client is connected to switchport fa0/7.i have only 3 devices altogether. below is running config of switch. wen i boot the client from the server, it display error message as: "proxy dhcp were offered. none dhcp were received. exiting broadcom pxe."
Switch#sh run
Building configuration...
Current configuration : 2710 bytes
!
version 12.1
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption[code].....
I have a 3560 series switch and two comcast cable modems. I connected the modems to them switch via cross over cables and set an OSPF routing on their subnets. I connected my wireless router to another port of the switch and set its gateway IP on the switch port. I can ping the modem with the switch and I can ping the wireless too. But I cannot access to the Internet via the wireless router.
I need load balancing on two cable modems and get a single network connection via the wireless router.
how to take the event log of Cisco switch 3560, its argent.
View 1 Replies View RelatedI have a 3560-48 switch running Cisco IOS Software, C3560 Software (C3560-ADVIPSERVICESK9-M), Version 12.2(44)SE3 and i need to implement basic QOS commands to the fast Ethernet interfaces as well as the gig interfaces and Also I need to create port channels on the switch and need what the port channel syntax are as well for that particular IOS version?
I have only read only access and i can't see what the QOS and Port channels syntax should be for that IOS version.
I have below switch and I was interested in configuring GRE on one of the interface. So I tried to create tunnel interface, the tab completes the command. Is GRE supported on this switch and IOS?
Switch#show version
Cisco IOS Software, C3560 Software (C3560-IPBASE-M), Version 12.2(35)SE5, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2007 by Cisco Systems, Inc.
......
cisco WS-C3560-48TS (PowerPC405) processor (revision G0) with 122880K/8184K bytes of memory.
Switch(config)#interface tunnel 0
^% Invalid input detected at '^' marker.
Switch(config)#
IP routing is also enabled.
I'm in the process of configuring QOS on a 3560 routing switch in a GOLD, SILVER, BRONZE priority type scenario.
Firstly, I understand that this config will add a tag of "precedence 5" to a packet if it matches the "ACL_QOS_GOLD_In" access list. Question is does the router see this "precedence 5" tag and then sets the priority, or am I missing something in my config where at present it just sees the "precedence 5" and doesn’t act on it ?
Secondly, Since the "precedence 5" tag has already been added to the packets, do downstream routers see this tag and act accordingly or so I need to configure those is well ? [code]
In our new Head office we have to set up a Network connectivity.Total our office 4 floors.In each floor we kept three cisco 2950 switch.We have L3 switch(cisco 3560) to connect the all the other switch.In our office total 5 departments.we have to create VLan for each departments in the switch.
We want to all user to communicate to each other.We have WAN connectivity in the router(cisco 2900) to connect the other office.First i want know how to physically connect all the swiches and finally with the L3 switch.How to configure the VLAN in both L2 and L3 switch.In our other client office one router to connect the both office.In the router how to configure and which protocol to use to communication.
Ip address:10.10.40.0/22
WAN IP :192.168.214.65/30
I have a 3560 switch 48 ports ios version 12.2( 35)SE5
I want to run two data vlans on the same port. Currently the port is in access mode and set to vlan30 I want to add vlan 40
I wanted to use multi mode, on this switch not an option but private-vlan is, ? what version of ios do I need to run the multi mode or can I do the same thing with private-vlan.
I was trying to apply route-map in Cisco 3560 Switch (C3560-IPBASEK9-M), Version 12.2 (55)SE5, I am able to create route-map but I am not able to apply it on any interface.
View 4 Replies View RelatedIm trying to Connect a 2960-S Catalyst Switch to a 3560 Catalyst Switch. It worth pointing out im newish to switching although i know some commands and what they do This is my first time connecting 2 switches together.They are connected via a crossover cable and have green lights flashing on the connected ports When i run "show CDP neighbours it sees the new switch Unable to ping new switch...just timesout Here is the the interface on the 3650
GigabitEthernet0/40 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet, address is 001b.532f.8428 (bia 001b.532f.8428)
Description: Uplink to Switch 2
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
[code]....
I'm unable to login Switch.......getting following error...I have tried this commands on other 3560 that worked...when I enter user name & password re logging authentication failed error occurs .........This is remote site Switch.
[code]...
I am configuring some quotes for a customer whom I will be building a wireless network for. The wireless network will support about 60 AP's, as well as some other wired drops. The customer is working with a wireless vendor for the AP's, but I will be able to sell the switches for the network.
I want to ensure that he is pushing Gig and POE on each copper port for the AP's, since they will be "N" capable. I have selected several 3560 models which are in 24 port models, and I also think i have a requirement which mandates a 48 port in another location. What I have not been able to find in the Enterprise switch line is an 8 port which supports IOS and POE.
That being said, and since I am also "Select" certified, I went out to the SMB site, and did find that there were two models in the Small Business 300 line (models SG300-10P and SG300-10MP) which seem to support Gig ports as well as POE. I looked over the specs for each one of the two respective models, and I was not able to find what the difference between each of these two are. In other words, the specs, line by line, were identical.