Cisco WAN :: Policy Routing Is Not Supported In 3560 Switch?

Jun 2, 2013

I was trying to apply route-map in Cisco 3560 Switch (C3560-IPBASEK9-M), Version 12.2 (55)SE5, I am able to create route-map but I am not able to apply it on any interface.

View 4 Replies


ADVERTISEMENT

Cisco WAN :: WS-C3560-48TS / Is GRE Supported On 3560 Switch And IOS

Feb 14, 2012

I have below switch and I was interested in configuring GRE on one of the interface. So I tried to create tunnel interface, the tab completes the command. Is GRE supported on this switch and IOS? 
 
Switch#show version
Cisco IOS Software, C3560 Software (C3560-IPBASE-M), Version 12.2(35)SE5, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2007 by Cisco Systems, Inc.
......
cisco WS-C3560-48TS (PowerPC405) processor (revision G0) with 122880K/8184K bytes of memory.
 Switch(config)#interface tunnel 0
^% Invalid input detected at '^' marker.
 Switch(config)#
  
IP routing is also enabled.

View 8 Replies View Related

Cisco Switching/Routing :: 3750 Service Policy Output Not Supported

Jan 26, 2009

I have a 3750 switch (c3750-ipbasek9-mz.122-46.SE.bin) were i want to add bandwitdh limit pr. interface, doing the following:
 
ip access-list extended customer_A
permit ip any any 
class-map match-all BW_10Mbps

[Code]....
 
When i trie to apply the "service-policy output 10 Mbps" to the interface, it says the service-policy output is not supported on the switch. Is this a software related isue ?

View 4 Replies View Related

Cisco Switching/Routing :: 3560 Policy Based Routing Verify-availability

Apr 19, 2012

Cisco 3560 does not support "set ip next-hop verify-availabilty". I need this command in my config. "set ip next-hop"  do not do the same job.

View 8 Replies View Related

Cisco Switching/Routing :: Make Policy Based Routing On 3560?

Apr 17, 2012

I have tried to make policy based routing on Cisco 3560. I use ipservices ios (SW version 12.2.(50)SE3 and SW-IMAGE C3560-IPSERVICESK9-M)  For below configuration there is no problem and pbr is working.
 
“Access-list 100 permit ip host  1.1.1.1 host 2.2.2.2
Access-list 101 permit ip host  1.1.1.1 host 3.3.3.3
 Route-map pbr1  permit 10
Match ip address  100
Set ip next-hop verify-availability  1.1.1.2 1 track 11
 interface fasthethernet  0/1
ip policy route-map  pbr1”
 
But when i add another sequence to the "pbr1" with another sequence number  like that.
 
“Route-map pbr1 permit  11
Match ip address  101
Set ip next-hop verify-availability  1.1.1.3 1 track 12”
 
pbr is not working. Switch gives message "PLATFORM_PBR-3-UNSUPPORTTED_RMP:Route-map pbr1 not supported for Policy Based  Routing”"ip policy route-map pbr1" command not shown in the running config. And "show ip policy" output is blank.Configuration guide says you have insert many sequence to the route-map with the same name. And also this command is not in the unsupported command list.

View 16 Replies View Related

Cisco WAN :: 3560 / Policy Based Routing With InterVLan Routing

Jan 14, 2011

I have 3560 with attached 3 networks, 172.16.1.0/24 172.16.2.0/24 and 172.16.4.0/24, all of them have a vlan interface, 172.16.1.254, 172.16.2.254, and 172.16.4.254, I have enabled intervlan routing with command ip routing and they have route beetwen each other. Now I want to create PBR and let them go to the internet from different gateways.

so i did 3 access list:

access-list 20 permit 172.16.1.0 0.0.0.255
access-list 10 permit 172.16.2.0 0.0.0.255
access-list 30 permit 172.16.4.0 0.0.0.255
and 3 pbr
route-map supnet permit 20 match ip address 10 set ip next-hop 172.16.2.3
route-map blade permit 20 match ip address 30 set ip next-hop 172.16.4.250
route-map main permit 20 match ip address 20 set ip next-hop 172.16.1.4
 
attached them to corresponding vlan interfaces and everything ok they have different gateways to internet but now I dont have routing beetwen them?

View 2 Replies View Related

Cisco WAN :: 7609-S Service Policy Output Command Not Supported?

Sep 26, 2012

I am facing issue while configuring service-policy output command in Cisco 7609-S router with c7600s72033-adventerprisek9-mz.122-33.SRE2.bin IOS. However, in the same series router having IOS c7600s72033-adventerprisek9-mz.122-33.SRC6.bin is supported service-policy output.Both the switch have WS-SUP720-3BXL  SUP.

View 2 Replies View Related

Cisco Switching/Routing :: Switch 6500 Policy Map Inbound

Jun 9, 2013

ON switch 6500 i have configured an interface vlan x and applied policies on inboud and outbound directions as per below: [code] But the problem i am facing is that the policy outbound works ok , but the policy inbound doesnt work at all. specifically it doesnt match anything. [code]

View 1 Replies View Related

Cisco Switching/Routing :: 6509-E Supported Switch Modules With Latest Stable IOS 12.(33)

Oct 14, 2012

I recently ran an upgrade on my 6509-E's and when the first switch came back up, 3 of the 10/100 switches that were in the chassis did not power on. After further investigation, these models are not supported by this latest IOS version. The module # is : WS-X6248-RJ-45
 
We have one WS-X6348-RJ-45 and since it was a few weeks ago I did this I can't remember for sure but I believe this one came up.
 
Where can I found the information regarding this being unsupported but I know it is out there and any page that showed me that this was unsupported with the latest stable IOS of 12.(33).
 
In addition to this question, I have approval to purchase some newer gigabit switches that will be supported by this new IOS version and hopefully at least the next few over the next few years. Which specific gig models are currently and hopefully should be supported for the next few years? I don't need PoE or anything spectacular, just regular switches that are attached to either servers or virtual hosts. I've been looking at the lists of what is out there and it seems like there are hundreds of different models and it is becoming difficult to determine what is what.

View 1 Replies View Related

Cisco Switching/Routing :: Policy Map Redirect Port 80 Switch 3750X

May 15, 2012

I would like to know if it possible to create a policy map in order to redirect the traffic ( 80 , http, 8080) to a proxy.
 
My current equipment its a 3750X using a IP Service License ,I was reviewing some options but i want to be sure before implement in production.

View 8 Replies View Related

Cisco Switching/Routing :: Switch 3750 / Policy Inbound Traffic Per IP?

Mar 2, 2012

We are using Cisco 3750 switches in our environment as distribution switches.We currently use to police inbound traffic, but we need to find a solution to limit inbound traffic per IP.Something like this “Inbound traffic for each IP can be maximum 1 Mbps” This can be done having, one ACL and one class-map for each IP, but in my situation is not a practical solution, because we have more than 500 IP’s on that site.
 
Is any way to accomplish this without writing 500 ACLs and 500 class-map?

View 2 Replies View Related

Cisco Switching/Routing :: Cat 3560 No Switchport Command Test Out Routing With Switch

Dec 8, 2011

The last few days I've been exploring options in getting rid of some old routers accross a wan connections.  I have a cat 3560 to play with and I thought I would try and use the no switchport command test out routing with switch.  I've got some type of route issue and I tried a few things which I thought would fix the issue but had no effect.  I'll post the config and a few commands so you can see what the basic setup is. 

Here we can see in the arp that it knows about both 10.7.1.2 (PC unable to ping 10.3.3.254) as well as 10.3.3.254 (ASA).I tried adding in a ip route of 10.7.0.0 255.255.0.0 10.3.3.110 as well as 10.3.3.254.  Neither produced the results I wanted allowing 10.7.1.2 (PC) to ping the ASA (10.3.3.254). [code]

View 4 Replies View Related

Cisco Switching/Routing :: 3560 VLAN Routing Between Switch And Router

May 8, 2012

I have an environment of 3 X 3560G of which I have 1st switch-CORE(f0/10) connecting to the VPN router(CE) interface-f0/0. Remaining 2 Cisco 3560's(Access) are connected to Gi0/1 and Gi0/2 on the 1st switch-CORE via gi0/1 . On all three switches I have created multiple VLANs and assigned ports to these VLAN. The switch to switch connection is trunk allowing all VLANs created on all these 3 switches. Now the issue is how I am going to have all these VLANs routed through single interface on the routeri-e f0/0, as all these subnets will communicating to remote site over VPN. What should be default gateway on the 2 Access switches and the CORE switch, also what static route should be on router to reach all subnets(VLANs) created on these 3 switches.
 
I have read inter-VLAN routing i-e creating sub interfaces on router but dont want to proceed with that and looking for any other way to have my VLANs talk on all three switches and then are accessible to remote site ove VPN?

View 9 Replies View Related

Cisco Switching/Routing :: Routing Secondary Network On 3560 Switch

Jun 4, 2013

I am trying to get my workstation to talk to a workstation on a different sub-net through a Cisco 3560 switch.  The switch is running the following IOS version: [code]
 
My primary network is 172.16.0.0 and I am trying to connect to a device on a 192.168.111.0 sub-net. [code]
 
What would be the best way to get the two workstations talking via the switch?

View 3 Replies View Related

Cisco Switching/Routing :: 3560 Switch With LAN QoS

Jun 5, 2012

I have issue with 3560 switch QoS configuration . I checked in cisco site about mentioned model QoS configuration.once we mark the frame and map the CoS to DSCP and once it enters into switch and it processes  according to LAN QoS configured on interface
 
we have configured  both the commands shape and share.
 
once it leaves the switch and enters into Edge router and if we do not have configured QoS in router which is normally MQC  , how does it process each packet ?Do we need to have end to end QoS configured in LAN ?

View 5 Replies View Related

Cisco Switching/Routing :: How To Take Event Log Of Switch 3560

Feb 26, 2012

how to take the event log of Cisco switch 3560, its argent.

View 1 Replies View Related

Cisco Switching/Routing :: Implement QOS On 3560 Switch?

Nov 22, 2011

I have a 3560-48 switch running Cisco IOS Software, C3560 Software (C3560-ADVIPSERVICESK9-M), Version 12.2(44)SE3 and i need to implement basic QOS commands to the fast Ethernet interfaces as well as the gig  interfaces and Also I need to create port channels on the switch and need what the port channel syntax are as well for that particular IOS version? 
 
I have only read only access and i can't see what the QOS and Port channels syntax should be for that IOS version.

View 3 Replies View Related

Cisco Switching/Routing :: QOS Config On 3560 Switch

Jul 22, 2012

I'm in the process of configuring QOS on a 3560 routing switch in a GOLD, SILVER, BRONZE priority type scenario.
 
Firstly, I understand that this config will add a tag of "precedence 5" to a packet if it matches the "ACL_QOS_GOLD_In" access list. Question is does the router see this "precedence 5" tag and then sets the priority, or am I missing something in my config where at present it just sees the "precedence 5" and doesn’t act on it ?
 
Secondly, Since the "precedence 5" tag has already been added to the packets, do downstream routers see this tag and act accordingly or so I need to configure those is well ? [code]

View 2 Replies View Related

Cisco Switching/Routing :: Configure QoS On 3560 Switch?

Jun 7, 2012

configure QoS on 3560 switch i have taken the template from cisco configuration guide since we have different QoS configuration on each model.
 
below is the configuration :
  
configure terminal
mls qos
end                  
mls qos map cos-dscp 0 8 16 26 32 46 48 56
no mls qos srr-queue input cos-map                mls qos srr-queue input cos-map queue 1 threshold 2 1                mls qos srr-queue input cos-map queue 1 threshold 3 0    

[code]....
 
Currently all the cisco phones are connected to this switch and configuration with only one vlan that is voice vlan .
 
1) what is the outcome of this configuration , i mean, what will be the expected output ? end of the day we need to prioritize the voice traffic but why other commands including threshold and buffers are mentioned with respectives queues , if I need to explain that what am i expecting out of this configuration ?
 
2) this is LAN QoS which i understood but again , do i need to configure policy-map along with class-map which is MQC on this switch ?
 
3) i have edge router where i have MQC already configured but confusion with this switch which is working as a Access switch .

4) I referred the cisco QoS document for the respetive model whereas we have policy-map configured on the same switch with class-map .

My understanding is if we have configured the LAN QoS , and mapped the CoS value with DSCP , we need not to have MQC.

View 4 Replies View Related

Cisco Switching/Routing :: 3560 - IOS On Switch Model?

Nov 9, 2011

I am configuring some quotes for a customer whom I will be building a wireless network for.  The wireless network will support about 60 AP's, as well as some other wired drops.  The customer is working with a wireless vendor for the AP's, but I will be able to sell the switches for the network.
 
I want to ensure that he is pushing Gig and POE on each copper port for the AP's, since they will be "N" capable.  I have selected several 3560 models which are in 24 port models, and I also think i have a requirement which mandates a 48 port in another location.  What I have not been able to find in the Enterprise switch line is an 8 port which supports IOS and POE.
 
That being said, and since I am also "Select" certified, I went out to the SMB site, and did find that there were two models in the Small Business 300 line (models SG300-10P and SG300-10MP) which seem to support Gig ports as well as POE.  I looked over the specs for each one of the two respective models, and I was not able to find what the difference between each of these two are.  In other words, the specs, line by line, were identical.

View 6 Replies View Related

Cisco Switching/Routing :: QOS For 3560 Access Switch

Nov 28, 2011

we have a class based qos scheme (see attached file) on our 4500 series access switches and we have a access 3560-48 switch runing IOS  Version 12.2(44)SE3 my question is can I use the same QOS scheme for the 3560 switch?

View 3 Replies View Related

Cisco Switching/Routing :: 3560 - Switch With 1 VLAN Configuration?

Mar 18, 2013

I have a 3560 switch with 1 VLAN (VLAN 10) where I need to make ports:

1-10 as isolated (can't contact each other)
11-20 as community (need to contact each other like a normal VLAN)
23 as promiscuous (server that ports 1-20 need to get to)
24 as promiscuous (WAN router where ports 1-20 need to get to and the remote servers).

[Code]...

View 26 Replies View Related

Cisco Switching/Routing :: Upgrade TAR IOS Image In 3560 Switch?

Oct 31, 2012

I wanted to upload image having .tar extension in Cisco 3560 switch. What are the steps to upload.

View 1 Replies View Related

Cisco Switching/Routing :: 3560 Switch Is Rebooting Daily

Feb 12, 2013

I have observed a situation where one of our cisco switch 3560 is rebooting daily at periodic times.We have checked the power cables and source everything is fine and still clueless whats causing the issue. [code]

View 13 Replies View Related

Cisco Switching/Routing :: Configure 3560 Switch With IP Cameras?

Aug 19, 2012

I want to configure Cisco 3560 SWITCH with IP cameras. I need to configure the ports connected to Camers. IP addresses to the Cameras has been assigned.

View 1 Replies View Related

Cisco Switching/Routing :: Switch 3560 Not Giving Out Power?

Sep 26, 2011

I have an issue with a 3560 in my network, after sometimes it fails to give out power to some ip phones,while others are not affected and below is the message i get
 
"Power given, but Power Controller does not report Power Good"

output of sh power inline and sh env all : everything seems to be ok on the switch

#sh power  inline
Available:450.0(w)  Used:48.0(w)  Remaining:402.0(w)
 Interface Admin  Oper       Power   Device              Class Max
                            (Watts)
--------- ------ ---------- ------- ------------------- ----- ----
Gi0/1     auto   off        0.0     n/a                 n/a   15.4
Gi0/2     auto   off        0.0     n/a                 n/a   15.4
Gi0/3     auto   off        0.0     n/a                 n/a   15.4

[code].....
 
It's solved by a reboot of the switch, i could have suspected a power environnment issue but it's the only equipement disturbing in the network.

View 20 Replies View Related

Cisco Switching/Routing :: Are LC SFPs Interchangeable With 3560 V2 POE Switch

Feb 7, 2012

Are the LC SFPs interchangeable with the 3560 V2 POE switchThe P/N number we have on the LC SFPs are 30-1301-04.Will this P/N number suit bothe the 2960-S and 3560 switches

View 1 Replies View Related

Cisco Switching/Routing :: No 802.1x Interface Commands On 3560 Switch

Aug 20, 2012

I am trying to configure 802.1x wired on a 3560 switch and don't see the required commands under the interface. I am running c3560-ipbasek9-mz.122-55.SE6.bin. I was thinking it might not be available on the ipbase image, but I do have the commands on a 3750g running the ipbase image, so I'm not sure about that.

View 4 Replies View Related

Cisco Switching/Routing :: Upgrading IOS Image On 3560 Switch

Sep 10, 2012

i am facing an error while upgrading the IOS image on 3560 switch. [code]

View 1 Replies View Related

Cisco Switching/Routing :: 3560 DHCP In Layer 3 Switch

May 25, 2012

I have made a topology by using one 3560 switch and 2 2950 switches. I have also made 2 vlans name Clients and other Servers and vlan 1 is for anagement purposes. The left 2950 switch is for clients and the right is for servers. Clients is vlan 2 and servers is vlan3 . Now what i want is that my dhcp is should assign ips to clients in vlans 2 provided that servers are in vlan 3. I am also using a border router and i have introduced a default route on the 3560 to the border router.
 
Now when i assign static ips to my clients pc and server dhcp then i can ping between vlans but when i try to assign ip through dhcp then it wont work. Also the default route on the switch to the border router doesnt seem to work. I can ping only the border router when i put a default route on the border router instead of the 3560 switch.

View 3 Replies View Related

Cisco Switching/Routing :: 3560 DHCP Between Switch And Router

Jul 23, 2012

I have a cisco 3560 24PS and its connected to two ADSL broard band routers.one is a personal broadband line using a Billion ADSL broadband router, and the other is a business broardband line using BT's 2wire broadband line.on the Billion routers i have various things attached like a NAS and a printers, both wired connections. then i have laptops and phones that connect over wifi, so its configured to act as a DHCP server
 
the only thing conncted to my 2wire router is my company's laptop (wired or wifi depending on where i'm working from), so again i have it working as a dhcp server.The switch is configured with multiple vlans, with dhcp scopes assigned for each vlan.I have a static route pointing all traffic to my Billion ADSL for internet connectivity.
 
The problem i'm having is that when i turn on the cisco switch, all wifi conected devices loose their conection. only 2 things get it working again, a reboot of the router, or disabling then enabling the DHCP service on the router.upon further analysis i was able to find out that the devices were not able to pick up an address from the router. again i looked deeper into this and i can see the following on logs of my router: [code]
 
so it seems that the router tuns off its DHCP capabilities because it detects that my Cisco switch is running DHCP services. I need to figure out how to keep the billion routers DHCP running when ever the switch is turned on.is there a way of filtering out any DHCP chat from the switch to the router?

View 7 Replies View Related

Cisco Switching/Routing :: 3560 - How To Replace VTP Server Switch

Apr 17, 2013

I want to replace an existing 3560 Switch with another switch of the same exact model and IOS. However, this switch that needs to be replaced is the VTP Server of my LAN at this location. When I replace the switch I will just use the same exact running config but I'm concerned about the vlan.dat file. Do I need to copy that file over to the new replacement switch and if so, what is the best way to do that?

View 5 Replies View Related

Cisco Switching/Routing :: 3560 - UDLD After Switch Reload

Sep 12, 2010

I have the following problem with

Situation:
- 2x 3750G-12S Distribution-Switches (DS) and several 3560/2960 Access-Switches (AS)
- redundant Fiber optic uplinks between AS and DS
- Cross-Stack Etherchannel config on all uplinks
- UDLD aggressive mode configured on all uplinks
 
Problem:
- when I reload the DS and the switch comes up again, I've lost the connection with several (not all) AS
- looking at the AS log I found the following error message: "%UDLD-4-UDLD_PORT_DISABLED: UDLD disabled interface Gi0/1, aggressive mode failure detected"
 
Cause:
- in the log of the AS I don't see intf Gi0/1 go down during the reload of the DS
- this means the DS didn't shuts down all its ports during the reload
- but this also means that UDLD on AS didn't know about DS reload, and therefore didn't resets counters
 
Workaroud/Solution
- I'm now configuring errdisable recovery on all AS
 
So I'm forced to configure errdisable recovery, even if I don't want.

View 3 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved