Cisco WAN :: WS-C3560-48TS / Is GRE Supported On 3560 Switch And IOS
Feb 14, 2012
I have below switch and I was interested in configuring GRE on one of the interface. So I tried to create tunnel interface, the tab completes the command. Is GRE supported on this switch and IOS?
Switch#show version
Cisco IOS Software, C3560 Software (C3560-IPBASE-M), Version 12.2(35)SE5, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2007 by Cisco Systems, Inc.
......
cisco WS-C3560-48TS (PowerPC405) processor (revision G0) with 122880K/8184K bytes of memory.
Switch(config)#interface tunnel 0
^% Invalid input detected at '^' marker.
Switch(config)#
IP routing is also enabled.
View 8 Replies
ADVERTISEMENT
Oct 21, 2012
I have a network running some 20 switches, two controllers and many AP's. All the devices that should be able to connect to cisco network assistant can successfully. However there is one switch that will show in neighbours but will give the message of “unable to connect to device” when I try and add it to the topology.
As far as I can see the config is identically to all other similar switches in the network. I can telnet from a switch (management VLAN) to the switch in question. However when I try to ping or telnet from the PC running network assistant (different subnet) I am unsuccessful. However I can ping/telnet to all other cisco device from this PC. The switch is a WS-C3560-48TS and I have included the config for firstly the switch in question and another switch of the same model and config that works correctly.
sho run
Building configuration...
Current configuration : 7363 bytes
!
version 12.2
no service pad
service timestamps debug datetime localtime
[code]......
View 2 Replies
View Related
Feb 14, 2012
I have a strange problem with one switch in my LMS 3.2.1 installation.It is a WS-C3560-48TS with IOS 12.2(50)SE3 running. I have nine switches with the same type and IOS running without problems.
I notice the problem because there were no UT data for that switch. In RME and CS it was managed.Checking SNMP and config of the switch, but can't find any issues.Because at this time LMS ran in version 3.2 I installed at first CM 5.2.1 and after that the patches for CSCtd49439 and CSCtg20882.Next step was RME 4.3.1 with a lot of patches for different issues. Then I installed the patch for the internal error of CS (CSCtd07131).And finally I installed LMS 3.2.1 and patch for CSCto46927.Last step was installing the latest device packages. I did this directly from the application because it is much better handling than do a manual download. No the system seems to be fully updated.
I had the hope that CM will now find and manage this one switch. But it is still not available.I can't find the device in the data collection. But I can find it in the "Include Devices From DCR", although I configured to fetch all devices from DCR automatically to CM. To manually include the device is not working, too.
P.S. I used that step-by-step update path because it worked on two other servers very well for me.
View 1 Replies
View Related
Jun 2, 2013
I was trying to apply route-map in Cisco 3560 Switch (C3560-IPBASEK9-M), Version 12.2 (55)SE5, I am able to create route-map but I am not able to apply it on any interface.
View 4 Replies
View Related
Mar 27, 2011
What is the difference between v02 and v03 of ws-3560-48ts-s switches? is it just small corrections or functionality?
View 2 Replies
View Related
Sep 9, 2010
I'm having some weird issues with our 3560 that's connected to an MPLS line. The speed of the port plugged into the providers equipment is 100Mb, but we're only allocated 10Mb of bandwidth from them, I tried to police our traffic out of the port using srr-queue bandwidth limit 10, however when I do that I get some really weird bandwidth results.
Using iperf I've run bandwidth tests with srr-queue bandwidth limit enabled and with it disabled, when it's disabled I get the full 10Mb as expected, however once I enable it I'm lucky to get 5Mb, and while the test is running connectivity between sites is almost useless (which is not the case if I disabled bandwidth limit). Is there anything special I should be doing when I have this enabled? I also have priority-queue out enabled with only one dscp marking placed in queue 1, with very little traffic hitting that queue, but regardless of what I do I can't get the expected bandwidth with the bandwidth limit command, even if I place my iperf traffic in that priority queue.
View 3 Replies
View Related
Nov 16, 2011
My clients switch is running out of Spanning-Tree instances (c3560 only supports 128 instances). I know that running RSTP with VSTP can mitigate this that all instances over 128 will be handeled by RSTP, but before I implement this are there any other thoughts out there on how to mitigate this. Would MSTP be able to handle more STP instances or MISTP perhaps?
View 3 Replies
View Related
Oct 11, 2012
We have a Cisco switch in each office and every now and then the port that has the D-Link Wireless AP (DAP-1522) connected to it goes to err-disable state. Actually sometimes even a regular port that has a cisco phone connected may also go to err-disable state (less often). So I have to telnet into the switch and issue shut and no shut command on that interface to get it back to life, then it works for a few days or weeks until it happens again. Any suitable configuraiton for that interface, that would prevent that from happening or a workaround ?
Here's the info:
Model: cisco WS-C3560-24PS and cisco WS-C3560-48PS
Image:c3560-ipbase-mz.122-35.SE5.bin
This is the log from one switch:
31w5d: %PM-4-ERR_DISABLE: psecure-violation error detected on Fa0/2, putting Fa0/2 in err-disable state
31w5d: %PORT_SECURITY-2-PSECURE_VIOLATION: Security violation occurred, caused by MAC address 74e2.f592.f7f2 on port FastEthernet0/2.
31w5d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to down
And from another, which is almost the same:
5d10h: %PM-4-ERR_DISABLE: psecure-violation error detected on Fa0/3, putting Fa0/3 in err-disable state
5d10h: %PORT_SECURITY-2-PSECURE_VIOLATION: Security violation occurred, caused by MAC address d8a2.5e31.2cf6 on port FastEthernet0/3.
5d10h: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3, changed state to down
5d10h: %LINK-3-UPDOWN: Interface FastEthernet0/3, changed state to down
Here's the configuration of fe interfaces (they are all alike):
interface FastEthernet0/2
description Voice & Data Combo Port
switchport access vlan 11
switchport mode access
switchport voice vlan 15
[code]....
View 3 Replies
View Related
Jan 23, 2013
We have a cisco stack with 5 ws-c3750-24p 12.2)55)SE3 c3750-ipbasek9-m switches. Can i add a switch to the stack that is the following model: ws-c3750g-48ts 12.2(25)see3 c3750-ipbase-m
View 3 Replies
View Related
Feb 18, 2013
I am having WS-C3560G-48TS switch with ios(c3560-ipbasek9-mz.122-58.E2.bin) and I am trying to use IPv6 feature in this switch model. More over I've upgraded this switch with many ios but none of them not supporting IPv6 feature. ios which supports IPv6 feature?
View 3 Replies
View Related
Oct 8, 2012
I have got my ccna voice lab configured and is up and running, my switch is configured with 2 differents Vlans (Data & Voice) and the fa 0/1 is configured as trunk port connecting to the CME router. I can telnet or ssh to all the devices on the network but only the switch in not accepting the request the only message I am getting is "request timeout".
View 12 Replies
View Related
Jul 23, 2012
Can a C3560-24PS switch with 32 MB flash be loaded with IOS 15? Will it be able to execute the code and function properly?
View 2 Replies
View Related
Jun 28, 2012
I have a problem, i would like todo MACSEC betwwen two switches cisco catalyst 3560-x but I know that for this operation i needed ACS server 5.1 is it possible to encryp dataflow without ACS server and if you have the configuration
View 7 Replies
View Related
Apr 15, 2013
I have a 2 cisco switches that are at different sites one is a Cisco CAT4500 and other 3560. The connection between the switches is a layer 2 fibre link. CAT4500 and 3560 both have VLAN interface ip addresses in order for me to connect to the switches.
I have PC A connected to CAT4500 and PC B connecting to 3560. All these devices are the same VLAN and in the same subnet. I do have trunk links all the way though allowing this vlan as we run vlans. From PC A, I can ping CAT4500, 3560 and even PC B. This tells me everything is fine regarding Layer 2 & 3.
As soon as I move PC B and connect it to the other switch CAT4500 or move the other PC vice versa (this happens in both directions). Both switches learn that the mac address has moved locations and updates its mac address table accordingly. So when I do a show mac address table and show arp, everything has learned and moved fine. However when I try to ping any other device from PC B I cannot. So the 3560 switch PC B was originally connected to, I can no longer ping, the switch cannot see the pc also. It is as if PC B has not learned anything from the switch and cannot respond or reply to any icmp. I have tried this with different end devices, same thing. I am now thinking it has something to do with the switch.
View 14 Replies
View Related
Sep 4, 2012
Is SSH v2 feature is supported on cisco 3560G switch for below image if no what is the latest image .
c3560-ipbase-mz.122-35.SE5/c3560-ipbase-mz.122-35.SE5.bin)
View 11 Replies
View Related
Nov 27, 2012
what are all the CLI commands supported by Cisco SFE 2000 switch?
View 2 Replies
View Related
Apr 18, 2012
The table referenced in the new 1.1 ISE guide show 12.2(33)SXI6 is the minimum version for support. Does this mean this version or above? Does ISE is tested in newer SXJ streams? We have a massive rollout of SUP720s to do and need to know the most stable version to load in preparation for ISE.
View 1 Replies
View Related
Jan 16, 2011
I am trying to find out if NBAR is supported on the 4507 switches with a Sup 6L-E module - I can't seem to find any info.
View 2 Replies
View Related
Oct 14, 2012
I recently ran an upgrade on my 6509-E's and when the first switch came back up, 3 of the 10/100 switches that were in the chassis did not power on. After further investigation, these models are not supported by this latest IOS version. The module # is : WS-X6248-RJ-45
We have one WS-X6348-RJ-45 and since it was a few weeks ago I did this I can't remember for sure but I believe this one came up.
Where can I found the information regarding this being unsupported but I know it is out there and any page that showed me that this was unsupported with the latest stable IOS of 12.(33).
In addition to this question, I have approval to purchase some newer gigabit switches that will be supported by this new IOS version and hopefully at least the next few over the next few years. Which specific gig models are currently and hopefully should be supported for the next few years? I don't need PoE or anything spectacular, just regular switches that are attached to either servers or virtual hosts. I've been looking at the lists of what is out there and it seems like there are hundreds of different models and it is becoming difficult to determine what is what.
View 1 Replies
View Related
Aug 8, 2011
how can i upload IOS in Switch when it is in ROMMAN Mode , its show IOS in flash but may pe Corrupt, show how can i put New ios in Switch 3560.
View 1 Replies
View Related
Apr 22, 2011
can i use normal two L3 Switch(3560) for BGP Multihoming with 2 different isp
View 4 Replies
View Related
Jun 26, 2011
How to configure SLA monitoring in 3560 switch. I have 2 DSL links terminating in switch and want to do WAN failover. I know how to do in ASA and router. I found IP SLA and track commands on switch but don't know exactly how to use them.
View 2 Replies
View Related
Jul 24, 2012
I am using Cisco 3560 POE -WS-C3560CG-8PC-S- switch for my AP's. The current IOS i got on this switch don't allow me to use web console. when i am click on webconsole i am getting attached. what is the best way of removing and installing new IOS.
View 5 Replies
View Related
Dec 17, 2011
I am looking for The latest IOS Available for cisco 3560 Series Switch, User guide for the same And All Supported features specification Guide.
View 7 Replies
View Related
Jul 13, 2011
I am having LMS 2.5 and nearly 50 cisco 3560 in my network. And I want to configure rcp. How can I do it.
View 1 Replies
View Related
Mar 9, 2013
why getting temperature event in 3560 switch, and we checked the Network room Temp it's normal around (22).
View 8 Replies
View Related
Jun 5, 2012
I have issue with 3560 switch QoS configuration . I checked in cisco site about mentioned model QoS configuration.once we mark the frame and map the CoS to DSCP and once it enters into switch and it processes according to LAN QoS configured on interface
we have configured both the commands shape and share.
once it leaves the switch and enters into Edge router and if we do not have configured QoS in router which is normally MQC , how does it process each packet ?Do we need to have end to end QoS configured in LAN ?
View 5 Replies
View Related
Oct 6, 2009
We are facing a weird problem of high CPU utilization on 3560 switch. Even without connecting a single PC to switch, CPU utilization is showing 22 %. Any particular reason for this? Can configuration affect the CPU utilization even though there is no PC connected?
View 5 Replies
View Related
Jul 21, 2011
pxe server ip address is 10.10.10.20 which is connected to switch port fa0/9 and client is connected to switchport fa0/7.i have only 3 devices altogether. below is running config of switch. wen i boot the client from the server, it display error message as: "proxy dhcp were offered. none dhcp were received. exiting broadcom pxe."
Switch#sh run
Building configuration...
Current configuration : 2710 bytes
!
version 12.1
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption[code].....
View 1 Replies
View Related
Apr 12, 2011
I have a 3560 series switch and two comcast cable modems. I connected the modems to them switch via cross over cables and set an OSPF routing on their subnets. I connected my wireless router to another port of the switch and set its gateway IP on the switch port. I can ping the modem with the switch and I can ping the wireless too. But I cannot access to the Internet via the wireless router.
I need load balancing on two cable modems and get a single network connection via the wireless router.
View 48 Replies
View Related
Feb 26, 2012
how to take the event log of Cisco switch 3560, its argent.
View 1 Replies
View Related
Nov 22, 2011
I have a 3560-48 switch running Cisco IOS Software, C3560 Software (C3560-ADVIPSERVICESK9-M), Version 12.2(44)SE3 and i need to implement basic QOS commands to the fast Ethernet interfaces as well as the gig interfaces and Also I need to create port channels on the switch and need what the port channel syntax are as well for that particular IOS version?
I have only read only access and i can't see what the QOS and Port channels syntax should be for that IOS version.
View 3 Replies
View Related
Jul 22, 2012
I'm in the process of configuring QOS on a 3560 routing switch in a GOLD, SILVER, BRONZE priority type scenario.
Firstly, I understand that this config will add a tag of "precedence 5" to a packet if it matches the "ACL_QOS_GOLD_In" access list. Question is does the router see this "precedence 5" tag and then sets the priority, or am I missing something in my config where at present it just sees the "precedence 5" and doesn’t act on it ?
Secondly, Since the "precedence 5" tag has already been added to the packets, do downstream routers see this tag and act accordingly or so I need to configure those is well ? [code]
View 2 Replies
View Related
