Cisco WAN :: SSH Version 2 Not Supported On 3560G Switch
Sep 4, 2012Is SSH v2 feature is supported on cisco 3560G switch for below image if no what is the latest image .
c3560-ipbase-mz.122-35.SE5/c3560-ipbase-mz.122-35.SE5.bin)
ADVERTISEMENT
AAA/Identity/Nac :: SUP720 ISE Supported Switch IOS Version
Apr 18, 2012The table referenced in the new 1.1 ISE guide show 12.2(33)SXI6 is the minimum version for support. Does this mean this version or above? Does ISE is tested in newer SXJ streams? We have a massive rollout of SUP720s to do and need to know the most stable version to load in preparation for ISE.
View 1 Replies View RelatedCisco WAN :: 3560G What Platform And IOS Version Need To Implement IOS SLB
Nov 27, 2011I want to select catalyst 3560G for my network. But IOS SLB need to be implemented in my network. I only know catalyst 6500 series can support this feature and i am not sure whether 3560G can support this feature. what platform and IOS version i need to implement IOS SLB?
View 1 Replies View RelatedCisco :: 2911 IP Route MIB Not Supported In IOS Version 15.0
Dec 14, 2011We've recently started using some 2911's on our network running IOS 15.0(1r)M9. I noticed, much to my frustration that the OIDs with the MIB RFC1213: ip RouteTable1.3.6.1.2.1.4.21 are not supported.
Any alternative MIB for viewing routing table information via SNMP on any of these devices running a similar IOS?
Cisco Application :: What Version Of Code Are Supported On ACE20
Mar 18, 2012I see several code versions that seem to support on ACE30.Is A2.3.4 Or A2(3.5) that latest version for ACE20-MOD-9?Will the version 4 or 5 run on ACE20?I currently user A2(3).
View 3 Replies View RelatedCisco Switching/Routing :: 2960 Which IOS Version Supported Stp Feature
Dec 19, 2012i want to know of the IOS verstion of cisco switch which support STP,some one told me that this feature is activated by deafalut if it not activated,how to turn on this Feature.i am using cisco 2960 Switch.
View 2 Replies View RelatedCisco Firewall :: ASA 5512-X Version 9.1 Multiple Contexts Supported?
Apr 3, 2013if on the ASA 5512-X virtual contexts are supported with version 9.1 ?
I found different information on the Cisco web, the ASA datasheet says it is supported but in the configuration guide I found exactly the opposite information.
Cisco ASA Series General Operations CLI Configuration Guide 9.1 and 8.6 [URL]
Cisco ASA 5500 and ASA 5500-X Series Next- Generation Firewalls for Small Offices and Branch Locations Data Sheet (Updated) [URL]
Cisco Wireless :: 5508 Controller Version 7.1.91.0 And Supported AP (List)
May 9, 2012I need to know for shure if the aps listed below are compatible with 5508 controller version 7.1.91.0
the ap's are
AIR-LAP1242AG-E-K9
AIR-LAP1242G-E-K9
AIR-CAP3501E-E-K9
AIR-CAP3502E-E-K9
AIR-LAP1231G-E-K9
of course I checked release notes [URL]
Cisco Switching/Routing :: C3560G-48 - IOS Version Option Or Not Supported On Hardware Platform
Feb 6, 2012We have 2 x C6506E and 2 x C3560-48's, they are all interconnected via port channels at 2Gb per channel. The 6506's are running CEF but the 3560's are not (The 3560's carry all our server traffic).When I do a show CEF on the 3560's it says %IPv4 CEF not running. There does not appear to be a global command to enable CEF on these switches.Is this an IOS version option or is not supported on the hardware platform?
View 3 Replies View RelatedCisco Switching/Routing :: Switch 3560G PoE-24 Not Booting?
Aug 13, 2012i facing problem with my switch cisco 3560G, when it power on only System light is green and noting happen. i check with serial cable ( Console) but noting happen no booting.
View 2 Replies View RelatedCisco Switching/Routing :: 3560G Random Spike In CPU On Switch
Jan 12, 2013We have a Catalyst 3560G 24 port POE switch. It's been running fine for 1+ years. A few weeks ago we enabled SPAN on it to capture packets. Today, we had a random spike in CPU on the switch. Seems hardware swithing continued to work fine, but software based processes choked and effectively took down EIGRP, HSRP, etc. We collect syslogs from the router and we saw 2 crashes/reboots. Both showed the exact same error both times, with the same hex values. I **believe** the CPU usage dropped when a tech disconneted the SPAN port and it's state changed to down, but I'm not 100% sure.Could this indicate an IOS bug (I'm hoping it's not a hardware failure)? And, how to track this down to see if this could be related to SPAN? I've disabled SPAN for now.
View 3 Replies View RelatedCisco Switching/Routing :: Getting A Connection Between PA-GE And 3560G Switch (4 SFP Ports)?
Jan 22, 2012I've a 7206VXR (NPE-G1) router. I would like to purchase a PA-GE port adaptor where I've to use a GBIC connector.
1. Is it possible to have a connection between PA-GE and a 3560G switch (4 SFP ports)? If yes, what type of cables & connectors are to be used?
2. Is there any GigabitEthernet port adaptors / modules for 7206vxr where I can connect RJ45 (cat 5) or SFP modules?
Cisco Switching/Routing :: 3560G Switch NTP Not Sync After IOS Upgrade?
Feb 21, 2012We have two 3560G-TS-E running 12.2(35)se2, configured as HSRP. Both are running ntp config "ntp peer 210.72.145.44" and it's pretty well that they get the correct time. Yesterday I upgraded the second device to IOS 12.2(58)se2 and ntp doesn't work now. I checked doc that 12.2(58)se2 runs ntp default version 4 so I change to "ntp peer 210.72.145.44 version 3" but still not work. I put here "show ntp" result for different IOS.
IOS 12.2(35)
SW01>show ntp status
Clock is synchronized, stratum 2, reference is 210.72.145.44
nominal freq is 119.2092 Hz, actual freq is 119.2022 Hz, precision is 2**18
reference time is D2EF12A5.2EB2DCB2 (15:07:17.182 GMT Wed Feb 22 2012)
clock offset is -4.6616 msec, root delay is 57.50 msec
[code]...
Cisco Switching/Routing :: Configuring OSPF On A Layer 3 Switch 3560G
Apr 12, 2013Configuring OSPF on a catalyst 3560G Switch to connect to our building next door by way of fiber. The other two switches in the other building are running OSPF, I am trying to connect to the other building and access a server which is on a switch running OSPF. I am trying to configure the switch here to run OSPF and be able to see the neighbor, but currently can't although I've identified the networks. Maybe I'm missing something, I've followed the instructions but something is not right.
View 15 Replies View RelatedCisco Infrastructure :: Route Internet Traffic To Different Gateway Using 3560G Switch
May 24, 2011My issue: I have installed a firewall within my network. Currently all my clients default gateway defaults to GW:192.168.1.1. I would like all my internet traffic to route to the firewall ip 192.168.1.30. My Primary switch ip is 192.168.1.10, which is a 3560G running 12.2(25)SEE2 IPBASE-M.
My main problem is, I do not have access to the gateway, so I am trying to route internet traffic from within my switch to the firewall. I have already tried Route-Map, but seems this version of the OS does not support. I have already tried Policy-Map, but same as above. I have also tried IP ROUT command, but it did not work either.
And remember, I would like to perform the routing from the switch, because I do not have access to the default gateway which is a router to perform forward internet traffic to the firewall.
Cisco :: Catalyst 3560G Series Switch - Wrong Temperature Reading
Feb 26, 2012I am trying to get the temperature reading from one of our 3560G Switches using SNMP. When I run an snmpget on the Switch it returns back to me a "1".
So when I run the following I get:
> snmpget -v1 -c public 192.168.x.xxx 1.3.6.1.4.1.9.9.13.1.3.1.3.1005
SNMPv2-SMI::enterprises.9.9.13.1.3.1.3.1005 = Gauge32: 1
But when I telnet to the device and run a "show env temperature status" I get:
# show env temp status
Temperature Value: 32 Degree Celsius
Temperature State: GREEN
Yellow Threshold : 51 Degree Celsius
Red Threshold : 61 Degree Celsius
So I'm not sure why I am getting a "1" when using snmpget on the OID 1.3.6.1.4.1.9.9.13.1.3.1.3.1005 which is (ciscoEnvMonTemperatureStatusValue)??
If I run the same OID on another 3560G Router I get the correct output from snmp....
Cisco Switching/Routing :: 3560G And 2950 Switch Trunk Discard Errors
Apr 15, 2010I have two 3560G 24 port switches. Each of them connects to some 3560G or 2950 switches. Trunks between 3560G are set as 1000/full. Trunks between 3560G and 2950 are set as 100/full. show int status also shows the interface negotiation is 100/full for trunks between 3560G and 2950. The issue is I keep getting outdiscard errors in trunks between 3560G and 2950. At 2950 switches, I see Recv-errors too. I checked all the trunks traffic. They are totally not high. Only serveal mbps. Most time even lower than 1mbps.
I googled this kind of issue online. I see it could be possibly caused by high volume traffic higher than the capacity. But it appears the traffic there is not high enough to cause this kind of issue. Is there any possiblity that could cause this problem?
The below is 3560G trunk configuration for 2950 switch
interface GigabitEthernet0/10 switchport trunk encapsulation dot1q switchport trunk allowed vlan 1-122,124-4094 switchport mode trunk speed 100 duplex full srr-queue bandwidth share 10 10 60 20 queue-set 2 priority-queue out mls qos trust cos auto qos voip trust
the trunk configuration at 2950 switch: interface FastEthernet0/24 switchport trunk allowed vlan 1-122,124-4094 speed 100 duplex full
Cisco Switching/Routing :: Can't Assign Switch 3560G Port G0/1 To Access Vlan 10
Feb 21, 2012cant assign cisco switch 3560G port g0/1to access vlan 10
main-switch(config-if)#switchport access vlan 10 Command rejected: Gi0/1 not a switching port.
Cisco Switching/Routing :: 3560G 15.0(2)SE - Show Platform Forward Command Crashes Switch?
Dec 5, 2012I have been working on some Catalyst 3750's running 12.2(55)SE6 and hit an issue with CEF load-balancing over multiple equal-cost paths. Anyway this issue is now solved but it introduced me to the command 'show platform forward' - this shows you how the forwarding of a packet would be done via hardware cef (as opposed to the command 'sho ip cef exact-route' command that only shows the software cef path). Anyway I tried the command on a 3560G running 15.0(2)SE and it crashes the switch. I tried it a couple of times and verified that the MAC & IP addresses were exactly right in the command and each time the switch crashes. I have extracted the relevant bits from the crashinfo and attached them.
View 3 Replies View RelatedCisco WAN :: WS-C3560-48TS / Is GRE Supported On 3560 Switch And IOS
Feb 14, 2012I have below switch and I was interested in configuring GRE on one of the interface. So I tried to create tunnel interface, the tab completes the command. Is GRE supported on this switch and IOS?
Switch#show version
Cisco IOS Software, C3560 Software (C3560-IPBASE-M), Version 12.2(35)SE5, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2007 by Cisco Systems, Inc.
......
cisco WS-C3560-48TS (PowerPC405) processor (revision G0) with 122880K/8184K bytes of memory.
Switch(config)#interface tunnel 0
^% Invalid input detected at '^' marker.
Switch(config)#
IP routing is also enabled.
Cisco Switches :: CLI Commands Supported By SFE 2000 Switch?
Nov 27, 2012what are all the CLI commands supported by Cisco SFE 2000 switch?
View 2 Replies View RelatedCisco WAN :: Policy Routing Is Not Supported In 3560 Switch?
Jun 2, 2013I was trying to apply route-map in Cisco 3560 Switch (C3560-IPBASEK9-M), Version 12.2 (55)SE5, I am able to create route-map but I am not able to apply it on any interface.
View 4 Replies View RelatedCisco WAN :: Is NBAR Supported On 4507 Switch With WS-X45-Sup6L-E Supervisor
Jan 16, 2011I am trying to find out if NBAR is supported on the 4507 switches with a Sup 6L-E module - I can't seem to find any info.
View 2 Replies View RelatedCisco Switching/Routing :: 6509-E Supported Switch Modules With Latest Stable IOS 12.(33)
Oct 14, 2012I recently ran an upgrade on my 6509-E's and when the first switch came back up, 3 of the 10/100 switches that were in the chassis did not power on. After further investigation, these models are not supported by this latest IOS version. The module # is : WS-X6248-RJ-45
We have one WS-X6348-RJ-45 and since it was a few weeks ago I did this I can't remember for sure but I believe this one came up.
Where can I found the information regarding this being unsupported but I know it is out there and any page that showed me that this was unsupported with the latest stable IOS of 12.(33).
In addition to this question, I have approval to purchase some newer gigabit switches that will be supported by this new IOS version and hopefully at least the next few over the next few years. Which specific gig models are currently and hopefully should be supported for the next few years? I don't need PoE or anything spectacular, just regular switches that are attached to either servers or virtual hosts. I've been looking at the lists of what is out there and it seems like there are hundreds of different models and it is becoming difficult to determine what is what.
Cisco AAA/Identity/Nac :: ACS1113 Version 4.2 Ssh Version 1 / Specify Only Version 2 Or Turn Off SSH?
Sep 14, 2009McAffee scan of acs 1113 appliance running the 4.2 build 124 patch 12 version reports that a medium vulnerability exists because the system has SSH version 1. Any way to specify only version 2 or turn off SSH?
View 9 Replies View RelatedCisco AAA/Identity/Nac :: 802.1X Switch IOS Version
Jul 12, 2012I' have realy big layer two access network made of etherogenius Cisco switch with different IOS version and train.My customer bought ISE (ADVANCED AND BASE LICENSE).As far I read on DS it is seem that if you have Minimum IOS release 12.2(52) SE you are able to perform COA, reading DS with more attention I notice that cisco raccomend IOS versione 12.2(55)SE3 why ? does it means COA does not work with 12.2(52)SE,I need a minimum IOS release to perform 802.1x on my wired network ?
View 1 Replies View RelatedCisco Switching/Routing :: IOS Version For C3500XL Switch?
Nov 13, 2007im trying to find out what is the latest ios version for 3500xl switch for upgrade it .
View 4 Replies View RelatedCisco Security :: Which IOS Version Of 3560-X Switch Support NAC-L2-IP
Apr 20, 2011Which IOS version of 3560-X switch support NAC-L2-IP ?
View 1 Replies View RelatedCisco Switching/Routing :: 3750-24TS-E Switch IOS And Hardware Version Compatibility
Nov 15, 2012I am confused about some things regarding the different IOS versions and their compatibility with certain switch hardware. I understand the differences between the IPBASE and IPSERVICES ios but am not quite clear as to how you can tell which ios images will work on which Cisco switch model platforms, other than the fact that some switches are designed only to run the IPBASE images and others have advanced hardware to run the advanced images. For instance, if I have a 3750-24TS-E with an IPBASE ios on it, can I load an IPSERVICES ios that came from say a 3750G-24TS-E1U? whether the ios on one platform can be transferred to another?
View 5 Replies View RelatedCisco Switching/Routing :: WS-C2960S-24TS-L / Switch Version Compatibility In A Stack
Dec 19, 2012We have the following stack configuration:
Switch Ports Model SW Version SW Image------ ----- ----- ---------- ---------- 1 28 WS-C2960S-24TS-L 12.2(55)SE3 C2960S-UNIVERSALK9-M 2 28 WS-C2960S-24TS-L 12.2(55)SE3 C2960S-UNIVERSALK9-M 3 52 WS-C2960S-48TS-L 12.2(55)SE5 C2960S-UNIVERSALK9-M * 4 52 WS-C2960S-48TS-L 12.2(55)SE5 C2960S-UNIVERSALK9-M
Cisco Switching/Routing :: 3560 And 2960 - Update Switch IOS Version At Packet Tracer 5.3
Oct 9, 2012I am using Packet Tracer to simulate Cisco networking.As the existing IOS of the 3560 and 2960 switch are in older version which has no new feature in new IOS, how to upgarde the IOS of Cisco switch at Packet Tracer?
View 5 Replies View RelatedCisco Security :: ACS 4.1 Version Recovery Disc On 4.2 Version To Recover Forgotten Password
Jan 16, 2012Can we use ACS 4.1 version recovery disc on 4.2 verison to recover the forgotten password.
View 1 Replies View RelatedCisco Wireless :: Which Version Of Prime Infrastructure Supports WLC5508 Version 7.4
Mar 11, 2013which version of prime infrastructure supports wlc5508 version 7.4
View 2 Replies View Related