Cisco WAN :: Is NBAR Supported On 4507 Switch With WS-X45-Sup6L-E Supervisor
Jan 16, 2011I am trying to find out if NBAR is supported on the 4507 switches with a Sup 6L-E module - I can't seem to find any info.
View 2 RepliesI am trying to find out if NBAR is supported on the 4507 switches with a Sup 6L-E module - I can't seem to find any info.
View 2 RepliesI was upgrading IOS on 4507 R with dual supervisor.I download the IOS on Active supervisior and did reboot.After reboot i login to switch then i got switch standby prompt.I found that after reboot active supervisior became standby supervisior.
Now new IOS is on standby supervisior.Need to confirm below..So this means that IOS does not syn within the supervisiors as compared to config right ?
-Which command i can use that will copy IOS from standby supe to Active supe??
-Which command i can use that will show both active and standby supe with new IOS?
-Is there any command that i can use to switchover from active to standby supe??
I have a problem connecting a PC in a TwinGig Convertors (GLC-LH-SM). I want to connect a PC with a fiber cable on the supervisor WS-X45-SUP6L-E of my Switch 4500E.
The default configuration mode is X2. As I want to deploy Gigabit interfaces (that is, use TwinGig Convertors), then I configured the associated port-group:
Switch(config)#hw-module module 1 port-group 2 select gigabitethernet
*Feb 24 06:18:37.125: Port Te1/2: TwinGig Converter inserted: vendor: CISCO
Switch(config)#do sh int status mod 1
Port Name Status Vlan Duplex Speed Type
[code]....
I noted that the Swicth set up automatically 'switchport mode trunk', so i put the command 'swicthport mode access' because i want to connect only a PC. But the status is the same, I can not achieve connectivity. i just want to know how connect a PC in the interface GigabitEthernet1/4 of the supervisor engine of my Switch.
Does the X2-10GB-T copper transceiver is supported on the WS-X45-SUP6L supervisor?
View 1 Replies View RelatedWe have ordered a new 4507 chasis with a supervisor engine.We have also ordered a spare supervisor engine.As per Cisco documentation WS-X45-SUP7L-E is shipped with a default IP base license.My question is that is this a e-delivery or a paper base license.The Cisco documentation also states that we can use the same license to upgrade both the redundant and active supervisor from lan base to IP base.
View 2 Replies View RelatedI have catalys 4507 with TWO supervisor V.I flowed this procedure : url...
after the reset normaly i can change the password and i check the confreg is 0X2142 but it still ask to enter the possword should i remove 1 supervisor and do the procedure or i must let the two spuervisor?
I am facing lots of issue with cisco 4507 switch recently.. Every alternate day, its CPU is getting utilized by 99% and network stopped working..finally it has to be restared.
Below is the CPU utilization of the process:-
------------------ show process cpu ------------------
CPU utilization for five seconds: 99%/0%; one minute: 99%; five minutes: 99%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
[Code].....
I have a 4507 cisco switch loaded with two sup-modules.. [code]
View 5 Replies View RelatedWe have 4507 distribution switch in our network.I am trying to enable ssh in those switches but seems that ssh command is not supporting. IOS version - cat4500e-universal.SPA.03.03.00.SG.151-1.SG.bin
View 1 Replies View Relatedi have a problem with a cisco cat. 4507 edge switch as when i have a login ssh session to the switch the supervisor engine restart and the redundant Sup. engine becomes the active and so on this problem mainly happen when i have multible SSH session to the switch and it happened very rarely with a single ssh login
the ios version i use is cat4500-entservicesk9-mz.122-54.SG which im using on all my edge switch and they are all working fine excpt this one
working first time on switch 4507 , this is my 2nd week and i plug the console on this 4507 switch , the switch reboots automatically it comes to stage mention below and reboots. My question is i have not seen any error message on this switch and it reboots automatically so what is the problem.
* *
* Welcome to Rom Monitor for WS-X4013+ System. *
* Copyright (c) 1999-2003 by Cisco Systems, Inc. *
* All rights reserved. *
* *
**********************************************************
Rom Monitor Program Version 12.1(20r)EW1
Supervisor: WS-X4013+ Chassis: WS-C4507
[code]...
We are facing issue of high Latency and slowness with Switch Cisco 4507R at the Customer site.show logging for the Switch and if there is any IOS related issue [BUG] or some other finding for this case.
View 1 Replies View RelatedI have version 2 ssh configured on a Cisco 4507r-e. Unable to sync archives with CiscoWorks. V2.99 is unsupported on CiscoWorks. Does CiscoWorks need to be updated or does the switch?
cat4500-ipbasek9-mz.122-52
LMS 3.2
# show run
ip ssh version 2
#show ip ssh
SSH Enabled - version 2.99
what is causing " Gigabit port is restricted to full duplex" while trying to hard code speed/duplex on a 4507 switch port?
View 3 Replies View RelatedWe will be connecting Cisco 4507 with Extreme Switches. We ran into spanning-tree issues last time. Extreme does not understand spanning-tree. So what i am thinking it to prevent bpdu advertisement from 4507 to extreme switches and also prevent incoming bddu from extreme switch to 4507. I am thinking of using
spanning-tree bpdu filter
spanning-tree bpdu guard
spanning-tree root guard
I buy a Cisco 4003 Switch with Supervisor Engine I but it only run CatOs and i whant it to run Cisco IOS so whitch Supervisor Engine can the Cisco 4003 Switch run? i have look at the Supervisor Engine III it can run Cisco IOS and Layer 3 but can i use that in my Cisco 4003 switch?
View 14 Replies View RelatedI will be start with the disclaimer that I am very technical, but a huge novice to the enterprise-grade Cisco swtiches.
How IOS software versions are licensed on a Catalyst 4507 switch? I am very confused at this point.
For example, if I buy IOS Enterprise Services for a new Catalyst 4507 switch, what form does the software license take? Is the license embedded on the switch? Does it come as an e-mail or certificate with a PAK? Does it come on a CD?
We sold a 4507 with Enterprise Services to a client, and they are saying they don't have the right IOS version installed. I assumed there must be some license key they needed, but the Cisco licensing help desk does not seem to indicate there are any licenesable items on our sales order number (even though IOS Enterprise Services is a line item on the sales order).
I know there was a disk that came with the switch with an Enterprise Services .BIN file on it, but I had assumed that was just a software version image, similar to the images I can download off the Cisco website. But is this actually the license key?
Since I can download image files off the Cisco website, I assumed there must be some other key needed to activate the license.
Switch is Catalyst WS-C4507R+E
Redundant Supervisors are WS-X45-SUP6-E (Supervisor 6-E)
Is it possible to view extensive information about switch supervisor on WS-C4506 platform? I could use show module or show inventory, but this only displays the module name. For example how to view the amount of SRAM the SUP has? Or any other similar more detailed information?
View 7 Replies View Relatedswitch catalyst 4500 with ios cat4500e-universal.SPA.03.02.00.XO.150-2.XO.bin. I need to configure modules 3 and 4 of supervision, the problem is that I need the 4-port module 3 are active but only the first turn on both the module 3 and the first port on the module 4. [code]
View 1 Replies View RelatedI have a supervisor blade, (VS-S720-10G-3C), in a 6513 that is faulty and needs replaced. Do I need to replace the IOS on the new supervisor blade to make sure it is the same as the IOS image that is on the Active supervisor module, or will it synchronize automatically?
In the synchronization process, the active supervisor engine checks the standby supervisor engine run-time image to make sure that it matches its own run-time image. The active supervisor engine checks three conditions:
#
•If it needs to copy its boot image to the standby supervisor engine
#
•If the standby supervisor engine bootstring needs to be changed
#
•If the standby supervisor engine needs to be reset
I was reading the above documentation that mentioned the active supervisor should copy the image if it detects a newly installed standby supervisor blade with a different image, is this correct or was it referring to synchronizing the configuration file?
We have a customer that has a fiber rum between 2 building. They want to have 2 seperate fibers active that terminate into the same switch on each end. (redundancy).
In building A they have an extreme networks black diamond switch that does not support STP.In bulding B they have a Cisco 4507.
We will ahve to use a layer 3 routed connection due to the fact their switch in building A does not support STP.Our tech does not want to use static route becuase he does not want to setup IP SLA for the redundant connection.
Will RIPv2 work for this scenario and failover to the other fiber if needed? The hop count is the same for each fiber path..
Is SSH v2 feature is supported on cisco 3560G switch for below image if no what is the latest image .
c3560-ipbase-mz.122-35.SE5/c3560-ipbase-mz.122-35.SE5.bin)
I have a Cisco 2801, IOS 12.4(24)T2 (C2801-IPBASEK9-M) on a WAN link to another 2801, which appears to be wrongly detecting our cross-site EMC replication traffic as Skype.
I am 100% sure that Skype isn't running on any of our PC's, yet the Skype protocol is by far the highest used out of everything. I have watched these traffic stats late at night when nobody is on the network and when the only traffic is replication, and this is the protocol which is constantly increasing.
If I run 'sh ip nbar port' , Skype isn't listed in the port-map. If I use ? at the end of the command, it lists Skype as option. The 'sh ip nbar protocol-discovery' show the following (among others):
FastEthernet0/1/0
Last clearing of "show ip nbar protocol-discovery" counters 6d10h
Input Output ----- ------ Protocol Packet Count Packet Count Byte Count Byte Count 5min Bit Rate (bps) 5min Bit Rate (bps) 5min Max Bit Rate (bps) 5min Max Bit Rate (bps) ------------------------ ------------------------ ------------------------ skype 76133998 146572068 6167477623 173614718864 0 0 1221000 8973000
EMC have informed me that the port used for replication is 8888, but I can't see how NBAR can think this is Skype.
why NBAR is detecting Skype traffic?!
Any comprehensive list of custom settings for NBAR V6 that will block most P2P traffic. The built in list seems incomplete. Either that or a way to better block P2P traffic at the router level.
View 1 Replies View RelatedI have below switch and I was interested in configuring GRE on one of the interface. So I tried to create tunnel interface, the tab completes the command. Is GRE supported on this switch and IOS?
Switch#show version
Cisco IOS Software, C3560 Software (C3560-IPBASE-M), Version 12.2(35)SE5, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2007 by Cisco Systems, Inc.
......
cisco WS-C3560-48TS (PowerPC405) processor (revision G0) with 122880K/8184K bytes of memory.
Switch(config)#interface tunnel 0
^% Invalid input detected at '^' marker.
Switch(config)#
IP routing is also enabled.
what are all the CLI commands supported by Cisco SFE 2000 switch?
View 2 Replies View RelatedI was trying to apply route-map in Cisco 3560 Switch (C3560-IPBASEK9-M), Version 12.2 (55)SE5, I am able to create route-map but I am not able to apply it on any interface.
View 4 Replies View RelatedThe table referenced in the new 1.1 ISE guide show 12.2(33)SXI6 is the minimum version for support. Does this mean this version or above? Does ISE is tested in newer SXJ streams? We have a massive rollout of SUP720s to do and need to know the most stable version to load in preparation for ISE.
View 1 Replies View RelatedIs there any docs with step by steps on upgrading the IOS software image on 4507R+E with dual sup6L-E ?
View 3 Replies View RelatedHow to hit the 32 interface nbar limit on an ASR? Our ASR1002 ESP5 is now grumbling: %NBAR-4-STILE_MAX_PD_INTF: NBAR protocol-discovery is enabled on maximum number of interfaces (32) supported by this platform..Is this expected to increase in future software revisions? (or is it a h/w limitation?)Is it the same limit regardless of ESP or will I get more (how many more?) if it is an e.g. ESP20?
View 1 Replies View RelatedI'm trying to upgrade NBAR protocol pack on my Cisco 1941 router, so i downloaded new NABR protocol pack (version 4.0.0) and transferred it into router flash via tftp. When i try to apply new protocol pack with command : ip nbar protocol-pack flash:[protocol-pack-name]
i got this error :
% NBAR Error : Advanced Protocol Pack can not be loaded on top of Standard Protocol Pack
The router is running IPBASE IOS with Security License, IOS image is c1900-universalk9-mz.SPA.153-1.T.bin. Does NBAR2 packages works on IO BASE images?
I recently ran an upgrade on my 6509-E's and when the first switch came back up, 3 of the 10/100 switches that were in the chassis did not power on. After further investigation, these models are not supported by this latest IOS version. The module # is : WS-X6248-RJ-45
We have one WS-X6348-RJ-45 and since it was a few weeks ago I did this I can't remember for sure but I believe this one came up.
Where can I found the information regarding this being unsupported but I know it is out there and any page that showed me that this was unsupported with the latest stable IOS of 12.(33).
In addition to this question, I have approval to purchase some newer gigabit switches that will be supported by this new IOS version and hopefully at least the next few over the next few years. Which specific gig models are currently and hopefully should be supported for the next few years? I don't need PoE or anything spectacular, just regular switches that are attached to either servers or virtual hosts. I've been looking at the lists of what is out there and it seems like there are hundreds of different models and it is becoming difficult to determine what is what.
How do I enable SSH on 4507. I do not see "ip ssh ..." commands config#ip ssh (I do not see "ip ssh " commnd)
Do i need to enable something else?
Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSAL-M), Version 03.02.00.SG RELEASE SOFTWARE (fc4)