Is it possible to view extensive information about switch supervisor on WS-C4506 platform? I could use show module or show inventory, but this only displays the module name. For example how to view the amount of SRAM the SUP has? Or any other similar more detailed information?
View 7 RepliesI have a Cisco 2610 series router(Version 12.0(5)T1, c2600-i-mz.120-5.T1), which has a network module inserted. I would like to view the model of this network module. There are no "show inventory" or "show platform" commands. "Show version" doesn't list the network module as well. In addition, it appears to have a "show c2600" command, but this doesn't display any hardware information.
View 14 Replies View RelatedWe have cisco 4506 and this got reloaded automatically and showing reload in show version output but no one made switch reload.
CORE-SW-2 uptime is 8 minutes
System returned to ROM by reload
System restarted at 12:37:58 IST Wed Dec 14 2011
I am not getting interface up/down logs in my switch console through show logging command. Switch model cisco WS-C4506-E and IOS :- cat4500e-ipbasek9-mz.122-53.SG3.bin. I have done below mention configurations, we can't configure logging level beyond informational. [code]
View 4 Replies View RelatedSwitch automatically restarts for no reason , I have upgraded the software.can not find fault. more crashinfo, see the following output:
HKZ-SSL-4-NAN-4506#more crashinfo:data
Current Time: 5/27/2013 10:28:10
Last Power Failure: 05/08/2013 16:55:28
Last Reload Status: 00000000
Last Software Reset State: 00000301
[code]...
I have been working on some Catalyst 3750's running 12.2(55)SE6 and hit an issue with CEF load-balancing over multiple equal-cost paths. Anyway this issue is now solved but it introduced me to the command 'show platform forward' - this shows you how the forwarding of a packet would be done via hardware cef (as opposed to the command 'sho ip cef exact-route' command that only shows the software cef path). Anyway I tried the command on a 3560G running 15.0(2)SE and it crashes the switch. I tried it a couple of times and verified that the MAC & IP addresses were exactly right in the command and each time the switch crashes. I have extracted the relevant bits from the crashinfo and attached them.
View 3 Replies View RelatedI have a switch cisco c 3750 that has vlan information, how to remove vlan information.
View 1 Replies View RelatedI use the Switch 2960S support PoE and 10 access points cisco.I have one more question:
-- If all 10 access points cisco use copper cable to connect to 2960S, 5 access points use power adapter and 5 access points use power from Switch. How Switch 2960S will provide power for 10 AP or switch 2960S will understand and only provide power for 5 APs?
how to connect WRT54G with E4200 (Wired / Wireless connection) ? I want to extend the coverage of WIFI signal, use E4200 guest WiFi feature and same to use the same SSID like E4200 (2.4Ghz and 5Ghz)
View 3 Replies View RelatedI am trying to find out if NBAR is supported on the 4507 switches with a Sup 6L-E module - I can't seem to find any info.
View 2 Replies View RelatedI buy a Cisco 4003 Switch with Supervisor Engine I but it only run CatOs and i whant it to run Cisco IOS so whitch Supervisor Engine can the Cisco 4003 Switch run? i have look at the Supervisor Engine III it can run Cisco IOS and Layer 3 but can i use that in my Cisco 4003 switch?
View 14 Replies View RelatedI am a very basic user on the Cisco Switch programming. I was given a Cisco 3750G-48 to tinker with in my home office. I was wondering if someone could lead me to some good sources of information to program and configure this switch? I am wanting to create a GB network in the house with the computers that I have and the storage arrays.
View 8 Replies View Relatedswitch catalyst 4500 with ios cat4500e-universal.SPA.03.02.00.XO.150-2.XO.bin. I need to configure modules 3 and 4 of supervision, the problem is that I need the 4-port module 3 are active but only the first turn on both the module 3 and the first port on the module 4. [code]
View 1 Replies View RelatedI have a supervisor blade, (VS-S720-10G-3C), in a 6513 that is faulty and needs replaced. Do I need to replace the IOS on the new supervisor blade to make sure it is the same as the IOS image that is on the Active supervisor module, or will it synchronize automatically?
In the synchronization process, the active supervisor engine checks the standby supervisor engine run-time image to make sure that it matches its own run-time image. The active supervisor engine checks three conditions:
#
•If it needs to copy its boot image to the standby supervisor engine
#
•If the standby supervisor engine bootstring needs to be changed
#
•If the standby supervisor engine needs to be reset
I was reading the above documentation that mentioned the active supervisor should copy the image if it detects a newly installed standby supervisor blade with a different image, is this correct or was it referring to synchronizing the configuration file?
I was upgrading IOS on 4507 R with dual supervisor.I download the IOS on Active supervisior and did reboot.After reboot i login to switch then i got switch standby prompt.I found that after reboot active supervisior became standby supervisior.
Now new IOS is on standby supervisior.Need to confirm below..So this means that IOS does not syn within the supervisiors as compared to config right ?
-Which command i can use that will copy IOS from standby supe to Active supe??
-Which command i can use that will show both active and standby supe with new IOS?
-Is there any command that i can use to switchover from active to standby supe??
Is there a command that can be used to view what type of SFP module that is installed in Catalyst 3750 switch?
View 6 Replies View RelatedI volunteer at a school who just purchased two 48 port SGE2010 managed switches. I am not a big fan of the web gui and was hoping to see the standard Cisco command prompt instead of the menu-type interface.
Is there a way to view the MAC table showing which MAC address is plugged into which port on the switch? I have been fighting with the menu and the gui for a while now and do not see this anywhere.
I am trying to setup 4 cameras to view with remote live view. I set up my server with IP addresses of 192.168.1.80 .... 85. The screen has only the option for 1 video channel. I have seen on-line screen shots that have options for channel 1 through 8. I want to assign each camera to a different channel so I will be able to use remote live view to show all 4 cameras at the same time. I can only show one at a time. Do I need a different version than 3.3 or some obscure windows 7 setting?
View 5 Replies View RelatedI've the following problem, configured dynamic user tracking on a WS-C4506-E with a WS-X45-SUP6L-E, System image file is a Version 12.2(53)SG2
Interface configuration:
snmp trap mac-notification change added
snmp trap mac-notification change removed
[Code].....
We are facing problem with Cisco IP phones which are connected to module WS-X4248-RJ45V.Phones are getting restarted and sometimes phones will not take power.Initially we suspected issue with power consumption, but we have enough power in the module.
View 3 Replies View RelatedI have two C4506 switches and I would like to create two L3 links between them by using only one physical link. I will then assign each L3 link to a different VRF.
I think I have two choices but I'm not sure however that the second one is possible...
---------------
1st choice: creating two VLANs and two SVIs on each switch
interface Vlan10
ip address 10.10.10.1 255.255.255.252
ip vrf forwarding vrf1
interface Vlan20
ip address 10.10.10.5 255.255.255..252
ip vrf forwarding vrf2(code)
What the message below means? It's from our WS-C4506-E log running Version 03.01.01.SG.
Dec 20 16:27:26.182: (Suppressed 851 times)Dup Packet Fail for Sw PortDec 20 2011 16:27:28.068 UTC: %LINK-3-UPDOWN: Interface GigabitEthernet4/22, changed state to upDec 20 2011 16:27:29.070 UTC: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet4/22, changed state to upDec 20 2011 16:29:13.738 UTC: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet4/22, changed state to downDec 20 2011 16:29:14.738 UTC: %LINK-3-UPDOWN: Interface GigabitEthernet4/22, changed state to downDec 20 16:42:37.173: (Suppressed 162 times)Dup Packet Fail for Sw PortDec 20 2011 16:42:39.071 UTC: %LINK-3-[Code]....
I have a problem with cpu high.tell me if normal have this process?
CPU utilization for five seconds: 29%/0%; one minute: 29%; five minutes: 30%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
29 198216576 402619350 492 15.83% 15.87% 15.68% 0 Cat4k Mgmt HiPri
30 175197296 96703435 1811 10.23% 10.10% 10.64% 0 Cat4k Mgmt LoPri
Cisco IOS Software, Catalyst 4000 L3 Switch Software (cat4000-I9S-M), Version 12.2(25)EWA14, RELEASE SOFTWARE (fc1)Technical Support: [URL] Copyright (c) 1986-2008 by Cisco Systems, Inc.Compiled Tue 20-May-08 18:49 by chendahImage text-base: 0x10000000, data-base: 0x114BE208
ROM: 12.2(31r)SG2Dagobah Revision 226, Swamp Revision 34
System returned to ROM by reloadSystem restarted at 00:36:52 UTC Sat Dec 10 2011System image file is "bootflash:cat4000-i9s-mz.122-25.EWA14.bin" cisco WS-C4506 (MPC8245) processor (revision 10) with 262144K bytes of memory.MPC8245 CPU at 266Mhz, Supervisor II+Last reset from Reload1 Virtual Ethernet interface144 FastEthernet interfaces2 Gigabit Ethernet interfaces511K bytes of non-volatile configuration memory.Configuration register is 0x2102
I installed WS-C4506-E 3 day ago. I discovered someting different module status Right at the end of the module ( WS-X4648-RJ45-E ) show red led. this is not port led i try to reset module several time. but it's same status. but this is operating now nomally I upload picture.. and this is module status and diagnostic result
Error code ------------------> 3 (DIAG_SKIPPED)
This Case is DOA(Dead of arrival ?
C4506#sh modChassis Type : WS-C4506-E
Power consumed by backplane : 0 Watts
Mod Ports Card Type Model Serial No.---+-----+--------------------------------------+------------------+-----------1 6 Sup 7L-E 10GE (SFP+), 1000BaseX (SFP) WS-X45-SUP7L-E ABCDE1234562 24 1000BaseX (SFP) WS-X4624-SFP-E ABCDE123456 6 48 10/100/1000BaseT (RJ45) WS-X4648-RJ45-E ABCDE123456
M MAC addresses Hw Fw Sw Status--+--------------------------------+---+------------+----------------+---------1 b0fa.ebe5.16c0 to b0fa.ebe5.16c5 1.1 15.0(1r)SG3 03.03.00.SG Ok 2 b0fa.ebc6.5b70 to b0fa.ebc6.5b87 1.2 Ok 6 10f3.1197.1490 to 10f3.1197.14bf 2.1 Ok
[code]....
I have 30 switched in my corporate network it’s all up and running all switches running by default configuration and connected to WS-C4506 core switch our dhcp server pooling 192.168.100.1/27 network. Now we need to configure new Vlan for finance department this department has more than 200 users. If my server distributes 192.168.200.0 range ip can vlan2 automatically assign ip 200.0 addresses to finance department.All switches running default config no ip address assigned.
View 9 Replies View RelatedWe are looking to deploy ISE supporting 5000 devices and would like to use the Cisco UCS platform to host this. Looking at the spec required a C22 M3 would be sufficient; however we would also like to host some UC applications on the same server if resources allow.
Therefore we would like to deploy ISE on a C220 M3 server and connect the associated NIC to a DMZ. We would then like to deploy UC applications such as CUCM and CUPS on the same UCS server with a NIC attached to the internal network.
Also while the UC application would require a UC Foundation License (R-VMW-UC-FND5-K9) whould this also meet the requirements for ISE?
I am doing a school research project in which I am setting up an OC-192 ring for a company (contract work through AT&T). I have chosen to use the Cisco ONS 15454 SONET MSPP as my platform. The company currently has locations in Chicago and Philadelphia and connects them through an OC-12C ATM connection and they are looking to add 2 gigabit ethernet connections.My question is what cards and parts will I need for the Cisco ONS 15454 SONET MSPP, and how much will everything cost? I have been searching the internet for components and prices and I have found it extremely difficult to find any information.
View 2 Replies View RelatedI currently have a 50Mbps Internet Connection provided by an ethernet handoff for hosting some webservers. We are looking at adding an additional 10Mbps Internetn connection and route BGP between the two. For the 50Mbps connection, i'm using a Cisco 2951 router. I also have another 2951 router to terminate the 10Mbps connection. Does these router have enough horsepower to fully route BGP?
View 1 Replies View RelatedIs there any way to auto migrate my 3030 VPN configuration to an ASA platform?
View 3 Replies View RelatedI want to select catalyst 3560G for my network. But IOS SLB need to be implemented in my network. I only know catalyst 6500 series can support this feature and i am not sure whether 3560G can support this feature. what platform and IOS version i need to implement IOS SLB?
View 1 Replies View RelatedA make one BOM and i just ask my self can we order on the one platform ( for example 5510-SEC-BUN-K9 ) SSL Essentials license ( this license is on the platform by default we buy 250 users ) and i need 50 Users license from them to be Premium.
Can i buy those two license on the same platform and is this will work ?
During WAN troubleshooting, I did a "clear interface ser0/0/0" on a branch router. It has two WAN links. I lost ssh/telnet connectivity but both WAN links were still replying to pings. We did a manual power off of the router to regain connectivity.Is there a known issue with this command on this IOS version? We're using Cisco 2911 platform with IOS 15.1-1.T2 version.
View 1 Replies View RelatedI am currently working on our Cisco voice platform at work.
Our Cisco firewall engineer has left and I have been given the task of looking after the firewalls as our Chief Exec seems to think that Cisco Voice is similar to Cisco ASA firewalls,
Are there any books/videos out that you can recommend to learn the about firewalls quickly.