We have cisco 4506 and this got reloaded automatically and showing reload in show version output but no one made switch reload.
CORE-SW-2 uptime is 8 minutes
System returned to ROM by reload
System restarted at 12:37:58 IST Wed Dec 14 2011
Switch automatically restarts for no reason , I have upgraded the software.can not find fault. more crashinfo, see the following output:
HKZ-SSL-4-NAN-4506#more crashinfo:data
Current Time: 5/27/2013 10:28:10
Last Power Failure: 05/08/2013 16:55:28
Last Reload Status: 00000000
Last Software Reset State: 00000301
[code]...
I am not getting interface up/down logs in my switch console through show logging command. Switch model cisco WS-C4506-E and IOS :- cat4500e-ipbasek9-mz.122-53.SG3.bin. I have done below mention configurations, we can't configure logging level beyond informational. [code]
View 4 Replies View Relatedwhile i am configuring a port on switch .The switch reloads.After reload the show version says
System returned to ROM by bus error at PC 0x458F6C, address 0x0
show version from the effected switch is
Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(58)SE2, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
[cODE].....
working first time on switch 4507 , this is my 2nd week and i plug the console on this 4507 switch , the switch reboots automatically it comes to stage mention below and reboots. My question is i have not seen any error message on this switch and it reboots automatically so what is the problem.
* *
* Welcome to Rom Monitor for WS-X4013+ System. *
* Copyright (c) 1999-2003 by Cisco Systems, Inc. *
* All rights reserved. *
* *
**********************************************************
Rom Monitor Program Version 12.1(20r)EW1
Supervisor: WS-X4013+ Chassis: WS-C4507
[code]...
A 4506 Switch reboot several times a day for no reason, I have been trying to upgrade the software . Normal operation of more than ten days , Still there reason to restart . CPU and memory usage is normal
Switch output information below:
HKZ-SSL-4-NAN-4506#sh ver
Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500e-ENTSERVICES-M), Version 12.2(54)SG1, RELEASE SOFTWARE (fc1) [ code].....
I Have a problem I'm trying to configure automatically my switch over ther DHCP when I start the switch it request an IP from the DHCP from here everythings is fine but it does nothing more,indeed I put on my dhcp the option 66 and 67 which is an adress of my TFTP server and a file to download and the switch seems not to understand theses options , I tried my dhcp with a cisco airport and everythings works fine the File from the TFTP is automatically downloaded into the airport...There is an option to add or am I missing something in order to make it work with my switch ?
My switch : Catalyst 2960IOS VER : 12.2(55)SE5
I have a 3845 router which got reloaded immediately and need to know the reason for the reload .Router have created crash info detail .
View 3 Replies View RelatedWe are facing problem with Cisco IP phones which are connected to module WS-X4248-RJ45V.Phones are getting restarted and sometimes phones will not take power.Initially we suspected issue with power consumption, but we have enough power in the module.
View 3 Replies View RelatedI have two C4506 switches and I would like to create two L3 links between them by using only one physical link. I will then assign each L3 link to a different VRF.
I think I have two choices but I'm not sure however that the second one is possible...
---------------
1st choice: creating two VLANs and two SVIs on each switch
interface Vlan10
ip address 10.10.10.1 255.255.255.252
ip vrf forwarding vrf1
interface Vlan20
ip address 10.10.10.5 255.255.255..252
ip vrf forwarding vrf2(code)
What the message below means? It's from our WS-C4506-E log running Version 03.01.01.SG.
Dec 20 16:27:26.182: (Suppressed 851 times)Dup Packet Fail for Sw PortDec 20 2011 16:27:28.068 UTC: %LINK-3-UPDOWN: Interface GigabitEthernet4/22, changed state to upDec 20 2011 16:27:29.070 UTC: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet4/22, changed state to upDec 20 2011 16:29:13.738 UTC: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet4/22, changed state to downDec 20 2011 16:29:14.738 UTC: %LINK-3-UPDOWN: Interface GigabitEthernet4/22, changed state to downDec 20 16:42:37.173: (Suppressed 162 times)Dup Packet Fail for Sw PortDec 20 2011 16:42:39.071 UTC: %LINK-3-[Code]....
One of my newly installed router got reloaded ,showing me below error . The same IOS im using in another router and it works fine without any issue ,but this newly installed router gave me this problem. [code]
cisco 7204VXR (NPE-G1) processor (revision B) with 983040K/65536K bytes of memory.
I have a problem with cpu high.tell me if normal have this process?
CPU utilization for five seconds: 29%/0%; one minute: 29%; five minutes: 30%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
29 198216576 402619350 492 15.83% 15.87% 15.68% 0 Cat4k Mgmt HiPri
30 175197296 96703435 1811 10.23% 10.10% 10.64% 0 Cat4k Mgmt LoPri
Cisco IOS Software, Catalyst 4000 L3 Switch Software (cat4000-I9S-M), Version 12.2(25)EWA14, RELEASE SOFTWARE (fc1)Technical Support: [URL] Copyright (c) 1986-2008 by Cisco Systems, Inc.Compiled Tue 20-May-08 18:49 by chendahImage text-base: 0x10000000, data-base: 0x114BE208
ROM: 12.2(31r)SG2Dagobah Revision 226, Swamp Revision 34
System returned to ROM by reloadSystem restarted at 00:36:52 UTC Sat Dec 10 2011System image file is "bootflash:cat4000-i9s-mz.122-25.EWA14.bin" cisco WS-C4506 (MPC8245) processor (revision 10) with 262144K bytes of memory.MPC8245 CPU at 266Mhz, Supervisor II+Last reset from Reload1 Virtual Ethernet interface144 FastEthernet interfaces2 Gigabit Ethernet interfaces511K bytes of non-volatile configuration memory.Configuration register is 0x2102
I installed WS-C4506-E 3 day ago. I discovered someting different module status Right at the end of the module ( WS-X4648-RJ45-E ) show red led. this is not port led i try to reset module several time. but it's same status. but this is operating now nomally I upload picture.. and this is module status and diagnostic result
Error code ------------------> 3 (DIAG_SKIPPED)
This Case is DOA(Dead of arrival ?
C4506#sh modChassis Type : WS-C4506-E
Power consumed by backplane : 0 Watts
Mod Ports Card Type Model Serial No.---+-----+--------------------------------------+------------------+-----------1 6 Sup 7L-E 10GE (SFP+), 1000BaseX (SFP) WS-X45-SUP7L-E ABCDE1234562 24 1000BaseX (SFP) WS-X4624-SFP-E ABCDE123456 6 48 10/100/1000BaseT (RJ45) WS-X4648-RJ45-E ABCDE123456
M MAC addresses Hw Fw Sw Status--+--------------------------------+---+------------+----------------+---------1 b0fa.ebe5.16c0 to b0fa.ebe5.16c5 1.1 15.0(1r)SG3 03.03.00.SG Ok 2 b0fa.ebc6.5b70 to b0fa.ebc6.5b87 1.2 Ok 6 10f3.1197.1490 to 10f3.1197.14bf 2.1 Ok
[code]....
Is it possible to view extensive information about switch supervisor on WS-C4506 platform? I could use show module or show inventory, but this only displays the module name. For example how to view the amount of SRAM the SUP has? Or any other similar more detailed information?
View 7 Replies View RelatedI have "inherited" a Catalyst 4506 with IOS version 12.2(20)EWA1 and Supervisor IV already installed. We recently purchased a second Supervisor IV and I am looking to install this second supervisor for redundancy. Is there anything special with installing a second supervisor or so I just physically install the new supervisor and the IOS will automatically set everything up?
View 3 Replies View RelatedI have 2 SG300 switches, in layer3 mode, lag'd together for high availability, serving 2 Dell R815's and a Dell Equallogic 4100 for virtualisation. I have setup a number of vlan's, network traffic, mgmnt traffic, iScsi, vMotion etc and they seem to work.
However, Equallogic unit suddenly became unavailable to view for managment yet maintained iscsi traffic for the servers ok. After much head scratching, noticed that one of my SG300's had the vlan ports assigned to various vlans had *automagically* changed there assignment, ie tagged changed to excluded, but only for one of the iscsi traffic connections and the mgmnt port, both coming from the Equallogic, the other iscsi continued its assignment fine. The other SG300 hasn't changed. Guaranteee no one has been into change it and no changes have been made to Dell servers or Equallogic.
Q. Is there any circumstance where the switch can change the port setup itself? or is there any external circumstance that would trigger that change either?
This has now occured twice. The setup is running as a test lab, not in production until all setup is complete, then it will replace our existing harware.
in my production environment two swtiches with stack and all ports are in the same Vlan 2 192.168.117.254 and the default getway is 192.168.117.1install correctely all were working fine but from yesterday onwards some of the ports are getting down automatically and coming up automatically and all devices are having static IP's no dynamic. [code]
View 6 Replies View RelatedI have encountered some weird issue on our Cat3750 running as DHCP Server.I have excluded 5 IP addresses only on the running configuration. [code]
View 1 Replies View RelatedI want upgrade IOS on my 7206VXR from 12.4(12c) to 15.1(4)M5 , but the CF card only 64M.
-NAME: "disk2", DESCR: "64MB Compact Flash Disk for NPE-G1"
-Router#show bootvar
BOOT variable = disk2:c7200-jk9s-mz.124-12c.bin,15.1(4)M5 is almost 40M. So there is not enough space.I want to ask is it ok if I upgrade with normal precedure , With the command " copy tftp: disk2: " ?Does the router will automatically delete the older IOS first and then copy into the new one ? Or Is there something I should pay attention first ?
I have a scenario where 15 c500 switches and 5 2960 8 port switch connected to 4507R core switch. There are 10 dhcp pools created on the 4507.
Eg: ip dhcp pool XXXX
network xxxx.xxxxxxx
default-router x.x.x.x
Now the default router is directed to vlans created on the switch i.e vlan 101, 102, 103 and so on. Now the remaining switches connected are configured to be in the same vlan. So the systems connected to the edge switches will get the DHCP ip automatically, Now my problem is after sometime (may be 2 or 3 hrs) all the edge switches are losing configuration automatically even though it's not restarted, even after saving the config on to nvram, everytime I connect the console and check all the saved config is lost?
We have upgraded our gateway router from a Cisco Linksys RVL200 to a Cisco 861, this is a big jump from a GUI driven system to IOS CLi and i'm having issue finding my feet. I tried the Cisco CP system but it didn't work so I'm going to configure it with IOS commands. I wish to replicate the current configuration on the 200 with the following setup.
I have created a DHCP pool but i am unable to configure the FastEthernet ports to hand out address automatically, the pool is called USERS with range 192.168.1.30 -> 192.168.1.253.How do I work out the client-identifier for a DHCP client, I don't want to plug this into the network and manual reconnect all the PC's just to get the ID then make a static route.
I would like to save power by scheduling the PoE switch ports on my switches to shutdown every night and turn on at a specified time during day.
View 6 Replies View RelatedI need 10gigbit uplink for this switch. What are the other devices that i need order along with this device.And what is the diff between X2-10GB-LR= and CVR-X2-SFP.if i take CVR-X2-SFP, in future how can i upgrade from one gig to 10 gig?for current use i need 10gig support required. so what are all the other devices that i need to order.Fiber multimode and distance 15Mt only.
View 2 Replies View Relatedi have an issue to connect a trunk between cisco switch and extreme switch i have many vlans that i want to cross via a link between cisco 3750 switch and a Extreme Alpine 3800 switch
View 12 Replies View Relatedwhat is the use of no switch port command in L3 switch?
View 7 Replies View RelatedI have two 3750-X configured to be a stack and I am planning to re-rack these somewhere else. What I would like to know is what are the effects of having the master switch itself lose power? Does it immediately just make the member take over master (there should be no election since there are only 2 switches??) and there would be no loss of connectivity?
View 1 Replies View RelatedI have a Catalyst 4006 switch in production and a spare switch of same model. I have to quickly copy the configuration from production switch to spare switch (both L2 and L3 configurations) How do I do that?
View 6 Replies View RelatedIt has been work for a year without problem. We didn't do any change. Recently, we have to reboot thist router to make it work. After the rebooting, the router will work for a while. It could work from few days to a week, and tt stops working again.
View 7 Replies View RelatedWe had some issue with Datacentre ACE modules. Both primary and DR ACE modules got restarted in 16 hours difference. Unfortunately Syslog was not configured on the ACE and local logging got cleared after restart. The current IOS version is A2(3.2). The modules uptime was around 300 Days. Here is the log from 6509 switch during the restart. [code]
View 7 Replies View Relatedreloaded xp. dont seem to have internet drivers. down loaded new drivers and seem to do no good. still unable to connect to internet.
View 1 Replies View RelatedI had a malware attack and decided to reload my XP Media Edition on my Dell XPS 400 series. After the disc reformat and reload of XP from the operating system CD, and then loading the drivers CD, I cannot connect to the internet. The plug for the ethernet cable is red/yellow on two different jacks in the house. The modem is supplied by ATT U-verse. The TCP/IP is connected at 400 Mb/s but showing "0" data transfer in or out. The internet connection was working before the XP reload. I did not backup an "image" and so I may have lost my registries? Is there a way to "turn on" the ethernet port?
View 5 Replies View RelatedOur router reloaded yesterday with a Software forced crash . I ant to identify the reason for the crash and also the fix for this problem . Attached is the crash info output .
[Code] ......