Cisco Switching/Routing :: WS-C4506-E / Module Status And Diagnostic Result Analysis
Mar 24, 2013
I installed WS-C4506-E 3 day ago. I discovered someting different module status Right at the end of the module ( WS-X4648-RJ45-E ) show red led. this is not port led i try to reset module several time. but it's same status. but this is operating now nomally I upload picture.. and this is module status and diagnostic result
Error code ------------------> 3 (DIAG_SKIPPED)
This Case is DOA(Dead of arrival ?
C4506#sh modChassis Type : WS-C4506-E
Power consumed by backplane : 0 Watts
Mod Ports Card Type Model Serial No.---+-----+--------------------------------------+------------------+-----------1 6 Sup 7L-E 10GE (SFP+), 1000BaseX (SFP) WS-X45-SUP7L-E ABCDE1234562 24 1000BaseX (SFP) WS-X4624-SFP-E ABCDE123456 6 48 10/100/1000BaseT (RJ45) WS-X4648-RJ45-E ABCDE123456
M MAC addresses Hw Fw Sw Status--+--------------------------------+---+------------+----------------+---------1 b0fa.ebe5.16c0 to b0fa.ebe5.16c5 1.1 15.0(1r)SG3 03.03.00.SG Ok 2 b0fa.ebc6.5b70 to b0fa.ebc6.5b87 1.2 Ok 6 10f3.1197.1490 to 10f3.1197.14bf 2.1 Ok
[code]....
View 5 Replies
ADVERTISEMENT
Jun 4, 2013
One of our Nexus 7000 modules failed and generated the status below. Could this possibly be a hardware issue?
# show module
Mod Ports Module-Type Model Status
--- ----- ----------------------------------- ------------------ ----------
1 0 10 Gbps Ethernet XL Module powered-dn
Mod Power-Status Reason
--- ------------ ---------------------------
1 powered-dn Unable to power up card (Power_OK not set)
View 4 Replies
View Related
Dec 7, 2011
We have two 6509 switches with one WS-X6704-10GE module in each of them. There is an optical cable between the two switches plugged in WS-X6704-10GE module on both sides. When you shut down the port on one side the other port still stays as up and you need phisycally to unplug the cable to have it down. The same behaviour is seen no matter on which of the two switches you shut down the port, the opposite one always stays as up and only removal of the cable makes it go down.
The ports are configured quite simply:
interface TenGigabitEthernet1/1
switchport
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1-10
no ip address
udld port
The IOS version is 12.2(18)SXF8
View 2 Replies
View Related
Dec 20, 2011
documentation on upgrading a WS-SVC-NAM-2-250S. I am looking to upgrade to 5-1-2 code if possible. I am only finding documentation for Prime version 3 NAM not version 2 that runs with 6500-SUP-720.
View 2 Replies
View Related
Jan 9, 2013
just found that on [URL], it stated that Cisco ASR 1000's management tool is Cisco Prime Network Analysis Module, which is same name as software that can be install in SRE of Cisco ISR G2 router for network analysis via web browser.
My question here is this mean Cisco ASR 1000 has built-in support for Cisco Prime Network Analysis Module, which has similar function as the one on Cisco ISR G2 router's SRE?
View 1 Replies
View Related
Sep 20, 2011
i have an issue for collect data on adapter 1, that don´t collect data but see that adapter 2 if collect data on module 4.
monitor session 1 source vlan 102 rx
monitor session 1 destination analysis-module 4 data-port 1
monitor session 2 source vlan 106 rx
monitor session 2 destination analysis-module 4 data-port 2
I reconfigured newly monitor and continues with that issue. Always ok by data-port 2.
- show version Cisco 6513
Cisco IOS Software, s72033_rp Software (s72033_rp-ADVENTERPRISEK9_WAN-M), Version 12.2(33)SXH7, RELEASE SOFTWARE (fc3)
. show version NAM
NAM application image version: 3.5(1b)
- sh module
Ports Card Type Model
----- -------------------------------------- ------------------
8 Network Analysis Module WS-SVC-NAM-2
Hw Fw Sw Status
------ ------------ ------------ -------
2.0 7.2(1) 3.5(1b) Ok
View 3 Replies
View Related
Mar 12, 2013
We are facing problem with Cisco IP phones which are connected to module WS-X4248-RJ45V.Phones are getting restarted and sometimes phones will not take power.Initially we suspected issue with power consumption, but we have enough power in the module.
View 3 Replies
View Related
Jul 3, 2012
I have two C4506 switches and I would like to create two L3 links between them by using only one physical link. I will then assign each L3 link to a different VRF.
I think I have two choices but I'm not sure however that the second one is possible...
---------------
1st choice: creating two VLANs and two SVIs on each switch
interface Vlan10
ip address 10.10.10.1 255.255.255.252
ip vrf forwarding vrf1
interface Vlan20
ip address 10.10.10.5 255.255.255..252
ip vrf forwarding vrf2(code)
View 1 Replies
View Related
Dec 20, 2011
What the message below means? It's from our WS-C4506-E log running Version 03.01.01.SG.
Dec 20 16:27:26.182: (Suppressed 851 times)Dup Packet Fail for Sw PortDec 20 2011 16:27:28.068 UTC: %LINK-3-UPDOWN: Interface GigabitEthernet4/22, changed state to upDec 20 2011 16:27:29.070 UTC: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet4/22, changed state to upDec 20 2011 16:29:13.738 UTC: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet4/22, changed state to downDec 20 2011 16:29:14.738 UTC: %LINK-3-UPDOWN: Interface GigabitEthernet4/22, changed state to downDec 20 16:42:37.173: (Suppressed 162 times)Dup Packet Fail for Sw PortDec 20 2011 16:42:39.071 UTC: %LINK-3-[Code]....
View 2 Replies
View Related
Dec 13, 2011
We have cisco 4506 and this got reloaded automatically and showing reload in show version output but no one made switch reload.
CORE-SW-2 uptime is 8 minutes
System returned to ROM by reload
System restarted at 12:37:58 IST Wed Dec 14 2011
View 8 Replies
View Related
Aug 30, 2010
I have a problem with cpu high.tell me if normal have this process?
CPU utilization for five seconds: 29%/0%; one minute: 29%; five minutes: 30%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
29 198216576 402619350 492 15.83% 15.87% 15.68% 0 Cat4k Mgmt HiPri
30 175197296 96703435 1811 10.23% 10.10% 10.64% 0 Cat4k Mgmt LoPri
Cisco IOS Software, Catalyst 4000 L3 Switch Software (cat4000-I9S-M), Version 12.2(25)EWA14, RELEASE SOFTWARE (fc1)Technical Support: [URL] Copyright (c) 1986-2008 by Cisco Systems, Inc.Compiled Tue 20-May-08 18:49 by chendahImage text-base: 0x10000000, data-base: 0x114BE208
ROM: 12.2(31r)SG2Dagobah Revision 226, Swamp Revision 34
System returned to ROM by reloadSystem restarted at 00:36:52 UTC Sat Dec 10 2011System image file is "bootflash:cat4000-i9s-mz.122-25.EWA14.bin" cisco WS-C4506 (MPC8245) processor (revision 10) with 262144K bytes of memory.MPC8245 CPU at 266Mhz, Supervisor II+Last reset from Reload1 Virtual Ethernet interface144 FastEthernet interfaces2 Gigabit Ethernet interfaces511K bytes of non-volatile configuration memory.Configuration register is 0x2102
View 1 Replies
View Related
Feb 7, 2013
I am not getting interface up/down logs in my switch console through show logging command. Switch model cisco WS-C4506-E and IOS :- cat4500e-ipbasek9-mz.122-53.SG3.bin. I have done below mention configurations, we can't configure logging level beyond informational. [code]
View 4 Replies
View Related
May 25, 2013
Switch automatically restarts for no reason , I have upgraded the software.can not find fault. more crashinfo, see the following output:
HKZ-SSL-4-NAN-4506#more crashinfo:data
Current Time: 5/27/2013 10:28:10
Last Power Failure: 05/08/2013 16:55:28
Last Reload Status: 00000000
Last Software Reset State: 00000301
[code]...
View 10 Replies
View Related
Jan 7, 2013
We just replaced our Cisco 1240 AP in one of our shops with a Cisco 1141 AP. This is not controller based.
We use several wireless (infrastructure mode) auto diagnostic tools which connect to the AP. We also have many laptops which run the diagnostic software.
We had no problems with our 1240AP. With our 1141, we cannot connect to the wireless tools if both the laptop and the tools are connected to the 1141. If I connect one to the 1240 and one to the 1141, they can see each other and work fine. IF they are both connected to the 1141, they show up as connected in the AP, they can ping each other, but the software does not communicate.
[URL]
View 7 Replies
View Related
Aug 18, 2012
The following error was seen on the switch and the Diagnostic Test Loop back failed following a new WS-6748-SFP module installation.Fabric in slot 5 detected excessive flow-control on channel 3 (Module 4, fabric connection 1)
Tried Hard reset of the module and still the error persist.
View 4 Replies
View Related
Feb 22, 2012
I had a sw/reset on my 6509 switch. The info in the crashinfo file pointed me to bug CSCso89550.
The workaround for this issue is to disable the gold diagnostics tool.
View 1 Replies
View Related
Feb 7, 2013
We just recently purchased a 3945 ISR G2 router and have a SRE-910 module (with two hard drives) configured in a Raid 1. We are running a stand-alone version of ESXi on the service module and I'm trying to figure out how to monitor the status of the Raid on the drives (along with other health issues). SNMP has revealed nothing so far and even opening a support case for which MIB's to use has proved fruitless. All the documents I find on monitoring the modules say to use LMS which is now Cisco Prime. I've downloaded the trial copy, put in the SNMP settings and scanned the router. I get device results and it shows that I have the SRE-910 module installed, but I get no other configuration / device informaiton from the module itself.
I tried to create a new Monitoring template using the NAM health as the base template (which I'm assuming this is the correct template). Unfortunately, when I actually try to deploy the template against the discovered router, I get an 'Unexpected end of list' error which makes me assume I'm still doing something wrong.
View 1 Replies
View Related
Aug 12, 2011
After inserting a RSP720-3C-10GE in module 6 and running the show module command display the following [code]what is the meaning of the UnKnown on the oline diag status ?
View 1 Replies
View Related
Aug 15, 2012
The problem is WiSM module not coming in OPER-UP status , it’s in Started-Keepalive status.I did run debug wism events on cat6509 and seeing below logs:
[code]...
It’s receiving garp request from controller and assign ip to controller but then keepalive time expired and it’s put the controller in started-keeplaive status.
View 4 Replies
View Related
Dec 7, 2011
We recently connected a RPS 2300 to our switch WS-C3750G-48PS-E with IOS c3750-ipservicesk9-mz.122-53.SE2.bin.However i do not see any RPS details in the"show env" output.I believe i should get the RPS Name and its Serial and the port number in the output, but i am not finding it in the output. I did reload the switch but still couldnot get this udpated.
View 3 Replies
View Related
Jun 5, 2013
We had to transport one of our 4948 10 GE to another Data Centre and when we got it there and tried to power up its System Status LED was red and we cannot even get console to the device.
We can try to see if the switch is completely dead and needs replacing or is there something we can do to get it back up and running again?
View 1 Replies
View Related
Dec 12, 2011
I have recently installed 4 3560 (WS-C3560X-48T-S) Switches. At first the switch comes up, indicating all connected ports with a green LED. Whenever i unplug a cable and plug it back in, the status LED will stay off. The same thing happens when I push the mode button and cycle throgh the different modes, i lose certain LEDs.
I'm using 12.2(53)SE2, another user reported the same issues under 12.2(55)SE1 .
View 4 Replies
View Related
Jun 8, 2013
I've Cat. 6509 with minfail status of DF card.There is no any errors in log and diag logs.
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 8 CEF720 8 port 10GE with DFC WS-X6708-10GE SAL1229XU2B
2 16 SFM-capable 16 port 1000mb GBIC WS-X6516A-GBIC SAL1227W6BZ
3 16 SFM-capable 16 port 1000mb GBIC WS-X6516A-GBIC SAL1227W6CD
4 16 SFM-capable 16 port 1000mb GBIC WS-X6516A-GBIC SAL1227W6BS
5 2 Supervisor Engine 720 (Active) WS-SUP720-3B SAL1228WPEB
[code].....
View 4 Replies
View Related
Mar 22, 2012
Below memory status alerts of are seen on our syslog server for Nexus 7K switch(Default VDC).
PLATFORM-2-MEMORY_ALERT_RECOVERED: Memory Status Alert : CRITICAL ALERT RECOVERED
PLATFORM-2-MEMORY_ALERT_RECOVERED: Memory Status Alert : MINOR ALERT RECOVERED
PLATFORM-2-MEMORY_ALERT_RECOVERED: Memory Status Alert : SEVERE ALERT RECOVERED
Memory threshold Not created on Nexus. Can we ignore this alert or does it impact our current network traffic?
View 5 Replies
View Related
Oct 16, 2011
I have installed and configured 2 new WS-3750E-24TD in the last 30 days, that have software version 12.5(50)SE2-universalk9, on our flat Development LAN (currently 7 existing WS-3750E-24TD with 12.5(35)SE2-universal)The new switches have shutdown, 1 has shutdown twice and I just had the other one shutdown on the weekend, all the status lights on the left are lit up but no port lights are on, I am not able to console in to the switch all I can do is cycle power. I am planning on upgrading all switches to the latest software release universalk9-mz.150-1SE
could this problem be a version incompatibillity between the switches?
View 8 Replies
View Related
Apr 19, 2013
In my 6513 switch chassis we have two Supervisor Engines 720 one is marked Active other as Hot. what is the diffrence in their mode as by name I suppose that Active one is currently in use and Hot one is in standby mode.They are showing in this manner.
Module Ports Card Type
7 2 Supervisor Engine 720 (Active)
8 2 Supervisor Engine 720 (Hot)
View 4 Replies
View Related
Feb 21, 2012
Why the IOS on 4500 doesn't support globally, although am running the IOS 12.2,need for logging event link-status global.
View 3 Replies
View Related
Feb 9, 2012
I enabled the "no service password-recovery" command on my C2960 switch. All seems to work as discribed. Only issue I have is --- which show command is used to reveal if the password-recovery feature is enabled of disabled as the command doesn't show up in the running config after you enable it ?
NOTE: The command does show up in the C2960 switch in config t mode (unlike the IOS router 2800 series), but doesn't show up in the running-config after you enable or disable it.
On the 2800 series routers (latest IOS) in config t mode the command does not show up but if you type "no service passowrd-recovery" the command function correctly and it does list it in the running configuration.
View 1 Replies
View Related
Feb 27, 2012
On a 4500 switch having a single sup engine, another sup engine was installed to act as redundant one.the redundancy mode was changed to sso, thereafter the secondary sup was prompted to be reset.
After it came back up again, the redundancy status still shows as RPR in operation mode.
View 9 Replies
View Related
Mar 5, 2013
I have a really weired thing happening on 6509 device with one of my customers.The device has a SUP 2 (MSFC2) with version 12.2.18SXF17B.
any VLAN interface once administratively down or simply down shows on "show interface status" output as VLAN.While it supposed to show "Routed". However once the port is up it is shows "routed" like it should.
View 5 Replies
View Related
Jun 10, 2013
i have a cisco router (3900 series) and a add on module (4 x 1 Gig port module). For some reason i cant seem to port channel them and cant do routing (can set an ip address on those ports). I can do port channel and routing on on-board ports. Do i have to enable any commands to do this ?
View 3 Replies
View Related
Jun 24, 2012
Was wondering if anyone has ever hot ADDED, not swapped, an expansion module in a 5548up. Is a switch reboot required?I looked at the H/W install guide and it does not mention anything.
View 3 Replies
View Related
Dec 3, 2011
My C6506 USING ws-sup720-3B, i upgrade the IOS to the latest release of 12.2(33) SXJ1 IOS version. After upgrade and reload the machine got one module cannot be detect..WS-X6416-GE-MT, 16 port 1000mb MTRK ethernet module. The version of this are:
-HW 1.0
-FW 5.3 (1)1
-SW 8.5 (0.46) RFW
Question 1: Any tools available on cisco to check out the hardware/software compabiity feature?
Question 2: Any release note, compability matrix table etc resources.
View 1 Replies
View Related
