Cisco Switching/Routing :: 4500 For Logging Event Link Status Global
Feb 21, 2012Why the IOS on 4500 doesn't support globally, although am running the IOS 12.2,need for logging event link-status global.
View 3 Replies
ADVERTISEMENT
Cisco Switching/Routing :: Logging Event Spanning-tree IOS 12.2(58)
Oct 20, 2011i can't configure "logging event spanning-tree" on a specific port under IOS 12.2.(58) SE2 (all other "logging events" are possible), under 12.2 (55) it is possible. Is it now a known bug or a default value?
View 4 Replies View RelatedCisco Switching/Routing :: 4500 Unable To Enter Global QoS Commands
Oct 11, 2009Unable to enter global QoS commands on the 4500E chassis? We're using 12.2(53)SG. If I go to 'conf t', there is no 'qos' command. In the configuration manuals I've seen for the 4500, the following commands seem to be supported:
qos
qos trust dscp
qos dbl
qos dbl exceed-action ecn
qos map dscp 0 to tx-queue 2
qos map dscp 8 10 12 14 to tx-queue 1
qos map dscp 16 18 20 22 to tx-queue 4
qos map dscp 24 26 28 30 to tx-queue 4
qos map dscp 34 36 38 to tx-queue 4
[Code] .....
Cisco Switching/Routing :: Catalyst 4500-E / Found BUG Between EEM And Remote Host Logging In Various IOS?
Sep 29, 2011I found a bug in Embedded Event Manager, on Catalyst 4500-E platform with supervisor V-10GE, on various IOS releases (in particular 12.2-50-SG IP BASE w/o crypto, 12.2-54-SG1 IP BASE w/o crypto, but also other releases included latest 15.0-2-SG1 ENTERPRISE SERVICES SSH).The problem is that when you set up a EEM applet that monitors syslog pattern matching, and you also configure remote host logging *with* the option "sequence-num-session", when the match occurs, the switch reboots with message:
Sw (sometimes prints a number instead)
VECTOR D00
and in some cases performs a second reboot with message:
VECTOR 0
DOUBLE FAULT
The reload reason message is:
System returned to ROM by abort at PC 0x0
The problem does *not* occur if remote logging has not the option "sequence-num-session". I verified this behavior on various configurations (included our production 130K long *and* factory defaults after erase startup-config).The configuration statements that cause reload are, for expample:
event manager applet prova
event syslog pattern %SYS-5-CONFIG_I
action 1.0 puts "configurazione modificata"
!
logging host 172.30.10.1 sequence-num-session
Cisco Switching/Routing :: 4500 Redundancy Status Still Shows As RPR In Operation Mode
Feb 27, 2012On a 4500 switch having a single sup engine, another sup engine was installed to act as redundant one.the redundancy mode was changed to sso, thereafter the secondary sup was prompted to be reset.
After it came back up again, the redundancy status still shows as RPR in operation mode.
Cisco AAA/Identity/Nac :: ACS 4.2 For Windows Feature Event Logging Not Supported In 5.2?
Nov 30, 2011Is the feature "event logging" that is present on ACS 4.2 with the option to "send all events to the windows event log" no longer supported in ACS 5.2?
View 1 Replies View RelatedCisco Switching/Routing :: 4500 / Layer 3 Port-channel Up But Can't Ping Across Link
May 17, 2012I configured the interfaces individually at L3 and could ping across each link Example:
4500 Switch 2: 6500 Switch 1
int t5/1 - int g3/17 1 Gig fiber link
tore down config
tried second set of interface
int t6/1 - int g8/17 1 Gig fiber link
Ping successful
[code]....
Cisco Switching/Routing :: How To Take Event Log Of Switch 3560
Feb 26, 2012how to take the event log of Cisco switch 3560, its argent.
View 1 Replies View RelatedCisco Switching/Routing :: 2960 ACL Triggered Event?
Apr 4, 2013I'm trying to enforce a triggered EEM applet with an ACL rule. Is this even possible? I've been searching for weeks, but the closest thing I can find is using an SNMP evenst, which isn't what I'm looking for. I've looked at the list of event triggers (and I've used resource events before), but I can't find anything that works.
I'm specifically trying to switch packet capture on/off (with a script or EEM applet) on some 2900 series routers. I have 2960s and 2911s.
Cisco :: 4500 Can't See Status Of Interface
Oct 27, 2012I do terminal monitor on my 4500 switch.I can't see the status of the interface ( when it become up or down)What is the problem? I need to add a command?
View 3 Replies View RelatedCisco Switching/Routing :: Embedded Event Manager On 3560 Switch
Jul 12, 2012I have EEM configured on cisco 3560 switch. The configuration is below. I want that switch inform me through email when device with particilular IP address become unavailable. I already try to debug this with debug event manager action mail but didn't see any output. [code]
View 2 Replies View RelatedCisco Switching/Routing :: 6500 - Dot1ad Global Configuration
Apr 3, 2012 I am facing problem about dot1ad global configuration command and my topology is here;
Notebook >> (access vlan 100) SW2960 (trunk)>> (trunk) C6500
First time I have create SVI interface on C6500 and enable trunk on interface that connected to SW2960 and SW2960 assigned access vlan 100 on port connected to Notebook. Then I tried to ping from Notebook to C6500 on SVI100 which work fine.
Second time I tried to enable MST on C6500 and after that everything still working and I can ping from Notebook to SVI100 on C6500.
Third time I tried on turn on dot1ad in global configuration mode and from now I can't ping from Notebook to C6500.
Forth time I tried to disable dot1ad from global configuration by "no dot1ad" command and then I can ping.
My intention is I would like to do EVC which require dot1ad in global configuration but I stuck in third step and don't know what's does it mean for this command and how I can resolve this issue?
Information on C6500
IOS Software (s2t54-ADVENTERPRISEK9-M), Version 15.0(1)SY1
Processor SUP-2T
Linecard WS-X6824-SFP
Cisco Switching/Routing :: 7600 / ES20+ Configure Global Command Mls Qos
Dec 18, 2012ES20+ QoS. As I understand for these cards QoS is MQC; i.e. similar to that of normal WAN cards
1- If i have 7600 with ES+ card only then I dont need to configure global command "mls qos" and the concept of trust boundries "mls qos trust dscp" will not exist , correct ?
2- For below output, why "show mls qos queuing" is giving an O/P similar to that of WS-X6xxx LAN modules.Also why it is WRR when scheduling is not configured.I expected that command will not work with this module as it is similar to WAN modules.
Cisco Switching/Routing :: 1841 Forward Port 8080 From Global To Local IP
Jan 5, 2012I have a cisco 1841 and I am hooking up some cameras onto my network. My global IP is 64.190.170.2 and my internal IP which is going to my cameras DVR is 192.168.1.15. I need to be able to forward port 8080 from my global IP to my local IP so i can view my DVR remotely. What is the command i need to put in my Cisco 1841 to forward this port?
View 2 Replies View RelatedCisco Switching/Routing :: Radius Server Command Missing From Global Configuration Mode 4510R
Feb 22, 2013I came across an interesting issue and thought I would see if anyone else has encountered it before contacting TAC.I have two Cisco Catalyst WS-4510R-E switches with a single Supervisor V module in each chassis. Both Sup cards are now running 12.2(54) SG1; ipbasek9 firmware; yes, I plan to move both switches to 15 code but that's another story. Anyways, prior to the upgrade the one switch was running 12.2 (33) code; I suspect the code was never upgraded; running ipbase non - K9 code. The other switch was running 12.2(44) with K9 prior to upgrade to 12.2(54).
View 2 Replies View RelatedCisco Switching/Routing :: Radius Server Command Missing From Global Configuration Mode 4510R-E
Apr 23, 2012I have two Cisco Catalyst WS-4510R-E switches with a single Supervisor V module in each chassis. Both Sup cards are now running 12.2(54) SG1; ipbasek9 firmware; yes, I plan to move both switches to 15 code but that's another story. Anyways, prior to the upgrade the one switch was running 12.2 (33) code; I suspect the code was never upgraded; running ipbase non - K9 code. The other switch was running 12.2(44) with K9 prior to upgrade to 12.2(54). With the background set, one switch reports the following:SwitchA (config)#r?radius-server redundancy regexp represourc rmon route-map router.
View 4 Replies View RelatedCisco Switching/Routing :: CoPP Logging On A 6500
Mar 19, 2013I am looking for a way to see packets that are matched on certain ACLs in a CoPP policy map. I have read that it is not a good thing to add the log keyword at the end of an ACL when using that ACL for CoPP. I initially tried to use a logging policy map but the 6500 12.2sx doesn't support this.
how I can see source/destination IP for a certain class in a CoPP policy map?
Cisco Switching/Routing :: Logging Commands On 6500
Oct 11, 2012I am looking for soem best-practice and useful logging commands on 6500 and 3750 platforms. Some of them I have listed below. Is there any important ones I am missing Also, I need to know what kind of recommended logging level is for buffer and what is loggign level for syslog server?
View 1 Replies View RelatedCisco Switching/Routing :: Logging Configuration On 4507?
Nov 8, 2012Is there any option to configure cisco 4507 to genrate log alert when cpu utilization or port utilization reaches above certain percentage.
View 2 Replies View RelatedCisco Switching/Routing :: 891 - Get Rid Of Logging Trap Debugging?
Oct 10, 2012As part of troubleshooting a seperate issue, somebody on my 891 router had set logging trap debugging which shows as a line in sh run just above the access-lists. There is no syslog server however so I'd like to remove this entry, however when I do no logging trap debugging I end up with a no logging trap entry replacing the previous logging trap debugging entry. Is there away to be rid of this entry? I tried no no logging trap but of course that's an invalid command.
View 6 Replies View RelatedCisco Switching/Routing :: Logging In Nexus 7010 6.x?
Sep 19, 2012We recently replaced our core switch from a non-cisco vendor with a Nexus 7010. With our old core switch, I had the ability to log changes to the ARP table. So if there was a dhcp conflict or a vMotion event, it would show up in the "show log" output. I've not found a way to do that with the Nexus switch - or at least no way to view the log. I have the command: logging level arp 6
View 8 Replies View RelatedCisco Switching/Routing :: What Logging Buffered 51200 Debug Do
Jan 7, 2013what logging buffered 51200 debug do?i saw it on cisco 881 sec k9
View 1 Replies View RelatedCisco Switching/Routing :: Could Not See RPS Status On WS C3750G 48PS
Dec 7, 2011We recently connected a RPS 2300 to our switch WS-C3750G-48PS-E with IOS c3750-ipservicesk9-mz.122-53.SE2.bin.However i do not see any RPS details in the"show env" output.I believe i should get the RPS Name and its Serial and the port number in the output, but i am not finding it in the output. I did reload the switch but still couldnot get this udpated.
View 3 Replies View RelatedCisco Switching/Routing :: 4948 10GE Red Status LED?
Jun 5, 2013We had to transport one of our 4948 10 GE to another Data Centre and when we got it there and tried to power up its System Status LED was red and we cannot even get console to the device.
We can try to see if the switch is completely dead and needs replacing or is there something we can do to get it back up and running again?
Cisco Switching/Routing :: 6513 - Disable Logging On Specific Port
Jan 18, 2012Ask this question, if someone came across a 6513, one of the RJ45 ports are constantly falling.The question is how to disable logging on a specific portno logging event link-status does not work.
View 1 Replies View RelatedCisco Switching/Routing :: Error In Logging Observed On 6513 Switch
Jul 15, 2012I have been getting the logs in my cisco 6513 switch [code] On further investigating in the module 9 which has a DFC card also , we found the source of this error whether it is a source of any upcoming potential impact or can be simply ignored
View 3 Replies View RelatedCisco Switching/Routing :: 2821 - HTTPS Logging / SSL Get Context Failed
Aug 28, 2008When i try logging by HTTPS on a router i have next errors.
%HTTPS: http ssl get context fail (-41104)
HTTP: ssl get context failed (-40407)
I have a 2821 router with
c2800nm-advipservicesk9-mz.124-15.T1.bin ios
Cisco Switching/Routing :: 3560 - Enable Informational Logging And Get All Messages?
May 9, 2012I have a situation in which I want to log a specific message (informational - 6 level), but don't want to enable informational logging and get all the messages that come with it. Is there a feature in IOS, 3560 12.2(25r)SEE4, similar to the 'logging lists' feature on the ASA that allows you to specify logs that you want to capture without having to change your logging level? I didn't want to have to write an EEM applet for this, but if that's the only way, I'd consider it.
View 3 Replies View RelatedCisco Switching/Routing :: 4096 / Syslog Message And Logging Command
Sep 21, 2012logging buffered 4096 warnings The above causes router to log all the events with severity level 4 or below in buffer.What about logging console warnings command?will the above command cause router to send log messages with severity level 4( warnings severity level) to console only or will the router send all the log messages with severity level 4 or below to console ?
View 3 Replies View RelatedCisco Switching/Routing :: C3560X Status LED Not Working Properly?
Dec 12, 2011I have recently installed 4 3560 (WS-C3560X-48T-S) Switches. At first the switch comes up, indicating all connected ports with a green LED. Whenever i unplug a cable and plug it back in, the status LED will stay off. The same thing happens when I push the mode button and cycle throgh the different modes, i lose certain LEDs.
I'm using 12.2(53)SE2, another user reported the same issues under 12.2(55)SE1 .
Cisco Switching/Routing :: WS 6509-E Card Status Minfail?
Jun 8, 2013I've Cat. 6509 with minfail status of DF card.There is no any errors in log and diag logs.
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 8 CEF720 8 port 10GE with DFC WS-X6708-10GE SAL1229XU2B
2 16 SFM-capable 16 port 1000mb GBIC WS-X6516A-GBIC SAL1227W6BZ
3 16 SFM-capable 16 port 1000mb GBIC WS-X6516A-GBIC SAL1227W6CD
4 16 SFM-capable 16 port 1000mb GBIC WS-X6516A-GBIC SAL1227W6BS
5 2 Supervisor Engine 720 (Active) WS-SUP720-3B SAL1228WPEB
[code].....
Cisco Switching/Routing :: Nexus 5000 Device Logging Configuration Required
Apr 7, 2013This is regarding CISCO logging configuration.We palnned to implement enable logging on all the cisco nexus switchs.we are running HP arc sight in our DC this device monitor all the CISCO devices.We want to enable logging with this Arc sight device.Just I would like to know about config commands for Nexus device, what is the command to enable logs which is include "who is login & logout?, interface down information?,who was did conf t ? & every logs"
View 8 Replies View RelatedCisco Switching/Routing :: 3750 - Configure Syslog Server For All Of Device Logging?
Feb 5, 2012I'm looking to configure a syslog server for all of my cisco device logging. I've had a look at CNA and can't find any options to define a syslog server for my switches.
What's the best way to define a syslog server and the severity of the notifications? Also, i'm looking to clear all previous Syste mmessages fon my devices?