I am looking for a way to see packets that are matched on certain ACLs in a CoPP policy map. I have read that it is not a good thing to add the log keyword at the end of an ACL when using that ACL for CoPP. I initially tried to use a logging policy map but the 6500 12.2sx doesn't support this.
how I can see source/destination IP for a certain class in a CoPP policy map?
I am looking for soem best-practice and useful logging commands on 6500 and 3750 platforms. Some of them I have listed below. Is there any important ones I am missing Also, I need to know what kind of recommended logging level is for buffer and what is loggign level for syslog server?
View 1 Replies View RelatedI was trying to configure copp on one of 6500 sup-2T. Is it ok to add customized policies to the default copp "policy-default-autocopp".When I created my own customized policy using policy-map, I get following error
control-plane service-policy input policy-custom
error: failed to install policy map policy-custom
According to release notes, this is available in v5.1.3-n1.1. I am running 5.1.3-n1.1a According to the security guide, all you should have to do is config t, then control-plane, but I do not have that option:
nx5k-2(config)# c?
callhome Enter the callhome configuration mode
cdp Configure CDP parameters
cfs CFS configuration commands
class-map Configure a class map
cli Configure CLI commands
clock Manage the system clock
nx5k-2(config)#
so my question is, is CoPP only available with the 5500s?
I'm configuring CoPP for an ASR 1001 router with consolidated IOS XE Version: 03.07.01.S. And I'm trying to use 'DROP' command under policy map to drop.un wanted traffic. But the drop command is not listed.
[code]...
On one of our N7K, we have some packets dropped by the COPP policy in the class-default class-map. Partial results of "show policy-map interface control-plane" not so long after clearing the counters : [code]
what traffic is dropped by the policy ? Is there any logging possible ?
Come across a problem with bgp logging on 6509-e with 12.2(17r)SX5 ?
View 1 Replies View Relatedhow can we upgrade 6500 non modular ios to normal 6500 ios?
View 5 Replies View RelatedIs there any option to configure cisco 4507 to genrate log alert when cpu utilization or port utilization reaches above certain percentage.
View 2 Replies View RelatedAs part of troubleshooting a seperate issue, somebody on my 891 router had set logging trap debugging which shows as a line in sh run just above the access-lists. There is no syslog server however so I'd like to remove this entry, however when I do no logging trap debugging I end up with a no logging trap entry replacing the previous logging trap debugging entry. Is there away to be rid of this entry? I tried no no logging trap but of course that's an invalid command.
View 6 Replies View RelatedWe recently replaced our core switch from a non-cisco vendor with a Nexus 7010. With our old core switch, I had the ability to log changes to the ARP table. So if there was a dhcp conflict or a vMotion event, it would show up in the "show log" output. I've not found a way to do that with the Nexus switch - or at least no way to view the log. I have the command: logging level arp 6
View 8 Replies View Relatedwhat logging buffered 51200 debug do?i saw it on cisco 881 sec k9
View 1 Replies View Relatedi can't configure "logging event spanning-tree" on a specific port under IOS 12.2.(58) SE2 (all other "logging events" are possible), under 12.2 (55) it is possible. Is it now a known bug or a default value?
View 4 Replies View RelatedAsk this question, if someone came across a 6513, one of the RJ45 ports are constantly falling.The question is how to disable logging on a specific portno logging event link-status does not work.
View 1 Replies View RelatedI have been getting the logs in my cisco 6513 switch [code] On further investigating in the module 9 which has a DFC card also , we found the source of this error whether it is a source of any upcoming potential impact or can be simply ignored
View 3 Replies View RelatedWhen i try logging by HTTPS on a router i have next errors.
%HTTPS: http ssl get context fail (-41104)
HTTP: ssl get context failed (-40407)
I have a 2821 router with
c2800nm-advipservicesk9-mz.124-15.T1.bin ios
I have a situation in which I want to log a specific message (informational - 6 level), but don't want to enable informational logging and get all the messages that come with it. Is there a feature in IOS, 3560 12.2(25r)SEE4, similar to the 'logging lists' feature on the ASA that allows you to specify logs that you want to capture without having to change your logging level? I didn't want to have to write an EEM applet for this, but if that's the only way, I'd consider it.
View 3 Replies View Relatedlogging buffered 4096 warnings The above causes router to log all the events with severity level 4 or below in buffer.What about logging console warnings command?will the above command cause router to send log messages with severity level 4( warnings severity level) to console only or will the router send all the log messages with severity level 4 or below to console ?
View 3 Replies View RelatedWhy the IOS on 4500 doesn't support globally, although am running the IOS 12.2,need for logging event link-status global.
View 3 Replies View RelatedI found a bug in Embedded Event Manager, on Catalyst 4500-E platform with supervisor V-10GE, on various IOS releases (in particular 12.2-50-SG IP BASE w/o crypto, 12.2-54-SG1 IP BASE w/o crypto, but also other releases included latest 15.0-2-SG1 ENTERPRISE SERVICES SSH).The problem is that when you set up a EEM applet that monitors syslog pattern matching, and you also configure remote host logging *with* the option "sequence-num-session", when the match occurs, the switch reboots with message:
Sw (sometimes prints a number instead)
VECTOR D00
and in some cases performs a second reboot with message:
VECTOR 0
DOUBLE FAULT
The reload reason message is:
System returned to ROM by abort at PC 0x0
The problem does *not* occur if remote logging has not the option "sequence-num-session". I verified this behavior on various configurations (included our production 130K long *and* factory defaults after erase startup-config).The configuration statements that cause reload are, for expample:
event manager applet prova
event syslog pattern %SYS-5-CONFIG_I
action 1.0 puts "configurazione modificata"
!
logging host 172.30.10.1 sequence-num-session
This is regarding CISCO logging configuration.We palnned to implement enable logging on all the cisco nexus switchs.we are running HP arc sight in our DC this device monitor all the CISCO devices.We want to enable logging with this Arc sight device.Just I would like to know about config commands for Nexus device, what is the command to enable logs which is include "who is login & logout?, interface down information?,who was did conf t ? & every logs"
View 8 Replies View RelatedI'm looking to configure a syslog server for all of my cisco device logging. I've had a look at CNA and can't find any options to define a syslog server for my switches.
What's the best way to define a syslog server and the severity of the notifications? Also, i'm looking to clear all previous Syste mmessages fon my devices?
I'm trying to view the logs from a Cisco 857W router to a workstation running the Kiwi Syslog server. what I've done is the following:
Config term
Logging on
Logging source-interface BVI1
Logging Facility Local7 (or any other facility you want to allocate for this router.)
Logging [IP Address or Hostname of machine running Kiwi Syslog Server]
End
I see noting on the syslog server. Although I can see the log information on the router Also is there a command to stop the logging from generating or is this on by default.
know Cisco IOS command, how to show when Catalyst 2960 was shut down (power off)?
View 2 Replies View RelatedI have a WS-C3560X-24 and attached to that are some 9 acces switches, for some weeks now my 3560 reboots some time what couse that the other 9 switches are down for some minuts as well and i dont want this of course. the reboot happens at random times and some times one week not and then like yesterday afternoon it rebooted again.
when i check the Flash directory there is no crash file and when i look at the logging its clean and just shows the startup. it's not the powersuply it's redundend and more L3 switches are attached to this power source and they dont reboot.
L3_AIM#sh versionCisco IOS Software, C3560E Software (C3560E-UNIVERSALK9-M), Version 12.2(55)SE3, RELEASE SOFTWARE (fc1)Technical Support: [URL] Copyright (c) 1986-2011 by Cisco Systems,
[Code]......
We have a design of two 6509 running in a VSS with dual supervisor each having fthree 10/100/1000mb etherner modules. We have diagnosed a wierd problem that none of the switchports in module 1 and 2 on either switches are having layer2/layer 3 connectivity.
Tried everything from changing the cables to changing the end device but no luck with it.
Module results show pass and no errors in the logging.
We had a core switch(4503) in our environment and recently we tried to enable syslog in the switch. But the syslog server doesnt receives all the configured level messages from the switch. Following is the only message getting in syslog server after the configuration change in switch.
%SYS-5-CONFIG_I: Configured from console by CWLMS onvty1
(No Traffic related messages like acl deny traffic, spanning tree events etc are getting to syslog server as well as log buffer of the switch)
Following are the logging configuration for the core switch
logging monitor informational
logging facility syslog
logging source-interface Vlan44
[Code]....
1) Is there any more configurations required for getting all traffic related messages, (i mean all possible messages - upto level 7 - debugging)?
I have a cisco 2811 router set up as a nat/firewall gateway for my network. I've configured it for CBAC on using ip inspect and an access list.What I want is to use audit-trail to record network traffic (which means sending syslog messages to a server) concerning established sessions from my own network to locations in the outside. If i configure this using ip inspect audit-trail and no ip inspect alert-off, the configuration looks like this: [code] which works just fine, but there is the matter of icmp packets.
Since i use polling software that needs to check some machines in the outside part of the network, it is only natural that several icmp sessions are established through the Inspection Rule per minute. The problem is that since these sessions are recorded along with everything else, my syslogs are flooded with these (since i am using logging trap informational) to the point that more messages are generated about icmp than all other traffic combined, especially in non-working hours.What I am asking is a way for the audit-trail to be selecively disabled for icmp, so that the outgoing (echo) &incoming (echo reply) sessions can be established without generating syslog messages.
I'm getting this error message on syslog server (Kiwi syslog)access-list logging rate-limited or missed XXXX packets i did the following commands but still I'm getting the error :logging buffered 16386 debugginglogging rate-limit all 5000no logging consoleno logging monitorip access-list logging interval 30000ip access-list log-update threshold 30000 i don't want to report to the console or monitor i want to report direct to syslog server, because I'm monitoring all the traffic (permit ip any any log) !
View 2 Replies View RelatedAs per my understanding 6509 all slots are dual channel, so 9 slot * 40 per slot (20 g in and 20 g out) = 360 GB How cisco claim the 720 ?? What about the 6513 chassic switch fabric connection?
View 5 Replies View RelatedI am seeing a strange situation on my 6500 switch?By having snmp walk on '1.3.6.1.4.1.9.9.109.1.1.1.1.3' (== cpmCPUTotal5sec), I came to know that there are two processor and the cpu util for switching processor is gone to 88 % and some time creeps to 99 %.
snmpwalk -v2c -c "removes" sw6500 '1.3.6.1.4.1.9.9.109.1.1.1.1.3'
SNMPv2-SMI::enterprises.9.9.109.1.1.1.1.3.1 = Gauge32: 12 (--- this is for CPU of Router Processor )
SNMPv2-SMI::enterprises.9.9.109.1.1.1.1.3.3 = Gauge32: 99 (--- this is for CPU of Switching Processor )
but when I do sh process cpu on the console, all looks normal as it shows cpu utilization of RP. why the value is so high on the switching processor ?
For intervlan routing, Is 'IP routing' command enabled by default on a 6500 series switches based on the IOS?and on 3750 switches, do we need to enable the "ip routing" command manually for intervlan routing?
View 1 Replies View RelatedI'm looking to restrict Inter-VLAN routing through L3 switch (cisco 6500) and wanted to know best possible way to do it. I used VACL and achieved success to some extent, but my config is making clients take up to 5-6 mins to authenticate IP address from the DNS (bootps).My VACL config was as follows:
Subnet to restrict is 10.100.15.0 (VLAN 15)
STEP 1: Created extended ACL to allow bootpc/bootps through DNS
ip access-list extended EACL_DNS
permit udp any eq bootps any
permit udp any eq bootpc any
STEP 2: Created standard ACLs to allow only relevant subnet, server VLANs & some IPs from other subnets for printers/scanners etc.
ip access-list standard SACL_VLAN_15
permit 10.100.15.0 0.0.0.255 (the subnet I'm restricting)
permit 10.100.50.0 0.0.0.255 (server VLANs)
permit 10.100.25.45 0.0.0.0 (printer in another VLAN which has to have access in VLAN 15)
STEP 3: Created VLAN access list
vlan access-map VACL_15 10
match ip address EACL_DNS
action forward
vlan access-map VACL_15 20
match ip address SACL_15
action forward
STEP 4: Applying VLAN Access list on VLAN 15 vlan filter VACL_15 vlan-list 15 Though the above works, below is noted:
1. I'm still able to PING 10.100.15.2 (the switch virtual interface) from outside the subnet, which I don't intend to do so. Howeve all cients in the subnet have no connectivity from outside the VLAN 15.
2. As mentioned its taking quiet some time to negotiate with the DNS server at system boot time.