I was trying to configure copp on one of 6500 sup-2T. Is it ok to add customized policies to the default copp "policy-default-autocopp".When I created my own customized policy using policy-map, I get following error
control-plane service-policy input policy-custom
error: failed to install policy map policy-custom
Im having this error on the 7609, but for other policy its working.
Code...
On one of our N7K, we have some packets dropped by the COPP policy in the class-default class-map. Partial results of "show policy-map interface control-plane" not so long after clearing the counters : [code]
what traffic is dropped by the policy ? Is there any logging possible ?
I am looking for a way to see packets that are matched on certain ACLs in a CoPP policy map. I have read that it is not a good thing to add the log keyword at the end of an ACL when using that ACL for CoPP. I initially tried to use a logging policy map but the 6500 12.2sx doesn't support this.
how I can see source/destination IP for a certain class in a CoPP policy map?
I am having Cisco 3845 series router with c3900-universalk9-mz.SPA.151-4.M2.bin IOS . I want to install new Licence on it for DATA. When i am trying to install licence on it i am facing the error "% Error: License installation failed with error: XML parsing failed".
View 4 Replies View RelatedI am trying to convert QOS policy on 6500 CAT to IOS as below,
1-getting error when try to apply on interface.
2-How can I apply both into one plicy map because IOS convertor puts into two policy maps.
CAT
set qos policer aggregate Limit_WSUS rate 4000 policed-dscp erate 4000 drop burst 1000 eburst 1000set qos policer aggregate Limit_SCCM rate 4000 policed-dscp erate 4000 drop burst 1000 eburst 1000clear qos acl all
#WSUSset qos acl ip WSUS dscp 0 aggregate Limit_WSUS ip host 172.16.9.3 any
set qos acl ip WSUS dscp 0 aggregate Limit_SCCM ip host 172.16.10.5 any
[code]....
ON switch 6500 i have configured an interface vlan x and applied policies on inboud and outbound directions as per below: [code] But the problem i am facing is that the policy outbound works ok , but the policy inbound doesnt work at all. specifically it doesnt match anything. [code]
View 1 Replies View RelatedI have few licenses to be installed in my c2911/k9 router but there were errors while installing the license. [code]
View 5 Replies View RelatedI'm trying to add an outbound policy on Layer3 interface on a 6500. The will be used to prioritize voice traffic. The environment contains 2 sites with 2 6500's each with VSS and a metro Ethernet link between them. I seem to be having problems prioritizing the voice across this link.
View 1 Replies View RelatedI´ve implemented 2 Cisco ISE v1.1 in HA to run MAB and 802.x Authentication / Authorization. Using Local ISE DB and Active Directory as an External Identity Source for wireless and wired users and devices. This was working fine 2 weeks ago after finishing installation.
My NAD devices are a Core SW 6500 for wired users (there are no access SW, just the Core for the whole network, its a small office) and a WLC 2405 for Wireless Users.[code].....
I have been tasked to replace a failed sup on a 6500 Sup32 running IOS. Now, the primary sup doesnt have a compact flash. I don't have any CF on me. The replacement sup i received also doesnt have a CF.From the cisco website it says that the moment I insert the secondary sup into the chassis. it will automatically download the IOS and boot details from the primary to the secondary sup.
[code]....
I Have a Firewall ASA 5505 with asa 8.4(2) asdm 6.4(5) I have only one Public IP services and need to publish on the Internet
External User (Internet) -> Calls connection on port 22 Internal server 192.168.1.124
External User (Internet) -> Calls connection on port 80 of the Internal 192.168.1.124 server or other server the same inside.
In the first moment I'm just testing the access port 22.I had it working in version 8.2 but after I updated to 8.4 does not work, I've tested several different configurations.
Configuration (see asa5505_config.txt file)
object network remoto_ssh
host 189.120.190.229
object network linux_ssh
host 192.168.1.124
nat (inside,outside) static remoto_ssh
access-list outside_access_in line 1 extended permit tcp any object linux_ssh eq ssh
ERROR: Address 189.120.190.229 overlaps with outside interface address.
ERROR: NAT Policy is not downloaded
I am trying to add 89,462+ access list rules to an ASA 5510 running 8.2(5). I have added all the rules to an object group and when I try to apply the access list to an interface it gives me the following error:
ERROR: Cannot add policy to rule engine ERROR: Unable to assign access-list wan-out to interface wan
I have not tried not using an object group and just putting the rules in the access list. I want to be able to add to these rules if needed easily.
I think it's clear that i have exceeded the rule limit for the ASA. So my question is, what is the rule limit for an ASA 5510 and which ASA could I purchase that would handle this amount of rules?
I have configured the primary firewall every thing seem to be fine, And we have configured fail over device while config is getting replicated to the fail over device we are getting below error.
ERROR: Cannot add policy to rule engine
ERROR: Unable to assign access-list LAN_out to interface inside
IOS and Model are same.But all the config got replicated from primary to secondary but except the one access group command.
access-group LAN_out in interface inside.
My firmware is 1.35NA and have a schedule established. When I try to add a policy for access control, I can select a policy name but when I hit "next", I get an error stating "Internet Explorer has stopped working" and wants to close. I was able to add policies previously but can not any more.
View 3 Replies View Relatedsample config for ASA 8.4 L2L VPN using Policy NAT?We could have multiple VPN tunnels terminated on the central ASA and our customer's LAN subnets could be interfering.Basically I need to build something like this [URL]but the problem is that I have ASAs running 8.4
View 2 Replies View RelatedHow to migrate a following VPN (site-to-site) config from ASA 8.2 to ASA v8.3,ASA 8.2
View 4 Replies View RelatedI have the following very simple policy configured on a Cisco 1841.
policy-map Shape-2Mb class class-default shape average 2000000 interface FastEthernet0/1[code]....
I'd just like some clarification on the best ways to monitor this. Looking at the 'sh policy-map int fa0/1' i get this:
FastEthernet0/1 Service-policy output: Shape-2Mb Class-map: class-default (match-any) [code]...
some of the sections don't make much sense to me. What is the output of that command.
In my head office we have Cisco 3845 router.in the router we put the show log command the below error is came..
What is the error??why the error came??
25024684: Feb 29 10:33:13.759 India: %FAN-3-FAN_FAILED: Fan 1 had a rotation error reported.
25024685: Feb 29 10:33:33.759 India: %FAN-3-FAN_FAILED: Fan 1 had a rotation error reported.
25024686: Feb 29 10:33:53.759 India: %FAN-3-FAN_FAILED: Fan 1 had a rotation error reported.
25024687: Feb 29 10:34:13.759 India: %FAN-3-FAN_FAILED: Fan 1 had a rotation error reported.
When I try to log-in to my D-Link DIR-835 Router using IE9, I get an 'Authentication Failed' error. FireFox & Chrome work just fine. what I need to change or fix in IE9 so it will also log-in to my router?
View 13 Replies View RelatedCannot get my Intel WiFi Link 5300 wireless card to install properly on my my Latitude 6500 using XP SP3. I can go to the Intel website and download the latest driver but once everything has been downloaded and ran, then restarted the wireless icon says that my driver is not installed.
View 13 Replies View RelatedI am running IOS version 8.0(5) in cisco ASA 5520. This issue i am facing is that when the memory utilzation reaches 49 percent, the web-vpn users are not able to login as they are getting a blank page. The only error which is getting in the output " sh mem webvpn allobjects" is ERROR: Memory allocation failed?
View 2 Replies View RelatedWhile installing ISE 3395 i am getting error failed to start DB!
Database is not available withintimeout of 240 seconds.this could be reason of incorrect network configuration or lack of resources on the appliance or VM, run the folloing CLI to re-prime database 'application reset-config ise'
I had upgraded the MSE to 7.0.202. Release code. The Upgrade along with the 4 database zips went smooth.But the MSE status shows following
View 2 Replies View RelatedGetting this error on the data center 2581 (12.4(24)T) from a GRE/IPSEC tunnel, remote branch is 2811 running 12.4(25d)
%CRYPTO-4-RECVD_PKT_MAC_ERR: decrypt: mac verify failed for connection id=
The tunnel has been up and working okay for months, nothing has changed on the config and the key is correct. Traffic is following but remote users are complaining of performance issues. A wireshark shows checksum errors and lots of packet resends. Remote ISP has checked the circuit and says its clean.The data centre router has quite a few tunnels but only 1 causing this issue. From the head end router -
sh crypto ips sa | b x.x.x.x
current_peer x.x.x.xport 500 PERMIT, flags={origin_is_acl,} #pkts encaps: 15129, #pkts encrypt: 15129, #pkts digest: 15129 #pkts decaps: 13346, #pkts decrypt: 13346, #pkts verify: 13346 #pkts compressed: 0, #pkts decompressed: 0 #pkts not compressed: 0, #pkts compr. failed: 0 #pkts not decompressed: 0, #pkts decompress failed: 0 #send errors 1, #recv errors 1992
Can a VPN module go bad like this? I've tried disabling the branch onboard engine and using software but it doesn't work.
Whenever I try to goto a webpage within any browser,despite me being connected to my network(though 1 received packet to every 20 or so sent packet ratio) it tells me that DNS lookup failed. I had a similar issue on my other pc that I use more often,though connecting through WIFI momentarily resolved the issue,before I returning to wired,where everything has been fine. My other pc however has no wifi adapter. So ive been stuck.
View 12 Replies View RelatedI have have a XPS L502X. I decided to make a clean installation based on Windows 7 Ultimate.My problem is when I instal the driver for the "Dell Wireless HSPA 5540" it fails with then warning:
"Authentication failed. The .... driver cannot be installed on this computer...."
How to install driver for this ?
I need to configure Policy Based Routing. There are two WAN Links from two Different ISP : Campus NW has one CORE switch - Cisco Catalyst 6506. [code]
View 3 Replies View RelatedI am unable to connect to the internet on my desktop computer. The error message I receive is" Download failed(12007) The sever name or address could not be resolved" I am running windows 7. Hooked up to att uverse. My laptop is working as you can see by sending this message. I have been trying to fix this problem for the last 2 days to no avail. I uninstalled norton hoping it was a firewall problem. On the local area connection it shows IPV4 connedtivety: No Network access.
View 2 Replies View RelatedI have just gone through hours of tech support with my ISP and still cannot seem to get online. Problem is the same as recent posts by jerguy1928, with message "DNS lookup failed...." coming up in Google Chrome. Both IE and FF just say cannot connect.Running Windows 7 on laptop. I have tried alt DNS settings (Google and others), all the CMD suggestions, disabling firewalls etc, etc! Other computer in house connects just fine.Ping works fine. Really, there appears to be no reason to not be able to connect - since I am actually connected!
View 13 Replies View RelatedDHCP Client and Network Location Awareness aren't working. When I tried to start DHCP Client, I got Windows could not start the DHCP Client service on the Local Computer.Error 5: Access is denied. I checked the dependencies and all of them were on. For Network Location Awareness, I got the error Windows could not start the Network Location Awareness on Local Computer. For more information, review the System Event Log. If this is a non-Microsoft service, contact the service cendor, and refer to service-specific error code -1073741288. One of its dependencies is fine, but I don't know how to check the other two, Ancillary Function Driver for Winsock and NetIO Legacy TDI Support Driver. Also, how do I check the event log?Everything on the list that was said to check is running expect these two the lisie was having problems with. I have not had anything with memory recently and have not been able to successfully go through a system restore. I have tried many of the suggestions and just am not sure what to do anymore. The computer works perfectly fine, minus it cannot get on the internet.
View 1 Replies View RelatedWhen I try to connect to our domain I get the error message:Changing the Primary Domain DNS name of this computer to "" failed. The name will remain "(name of our domain)" The specified domain either does not exist or could not be contacted.The procedure is the same I've used since Hector was a pup and never had a problem. I can't add users to the domain and can't log on directly to the domain.
View 1 Replies View RelatedI am using URL Snooper to copy URLs from slide share into my hard drive. Although my internet connection is working fine i am getting the message"ERROR:failed to find a suitable network driver". I cannot understand what the problem is" Please assit me in this issu
View 1 Replies View Related