While installing ISE 3395 i am getting error failed to start DB!
Database is not available withintimeout of 240 seconds.this could be reason of incorrect network configuration or lack of resources on the appliance or VM, run the folloing CLI to re-prime database 'application reset-config ise'
DHCP Client and Network Location Awareness aren't working. When I tried to start DHCP Client, I got Windows could not start the DHCP Client service on the Local Computer.Error 5: Access is denied. I checked the dependencies and all of them were on. For Network Location Awareness, I got the error Windows could not start the Network Location Awareness on Local Computer. For more information, review the System Event Log. If this is a non-Microsoft service, contact the service cendor, and refer to service-specific error code -1073741288. One of its dependencies is fine, but I don't know how to check the other two, Ancillary Function Driver for Winsock and NetIO Legacy TDI Support Driver. Also, how do I check the event log?Everything on the list that was said to check is running expect these two the lisie was having problems with. I have not had anything with memory recently and have not been able to successfully go through a system restore. I have tried many of the suggestions and just am not sure what to do anymore. The computer works perfectly fine, minus it cannot get on the internet.
View 1 Replies View RelatedAlthough, ACS states its installed, after going through the startup. However when I do show application nothing comes up. When I do a application start acs, %Application failed to start.
View 7 Replies View RelatedI have just change the DNS domain name of my ISE from CLI and restarted the appliance (its a 3395 appliance)However,, when i log in via GUI it doesnt reflect the new dns name.
View 1 Replies View RelatedI have an ISE 3395 appliance that comes with ISE version 1.1.1.I've decided to upgrade it to version 1.1.2 patch 5 (latest patch version) and played with it for a few days. I set it up as a stand-alone box.
Now, I need to deploy this box as administration and monitoring. So, I put in the command "application reset-factory" to set it back to factory.Does it mean the ISE version of this box will still be at version 1.1.2 patch 5 and I will get a clean box to do whatever I want, similar to Cisco IOS of "write erase" and "reload" to have a clean box?
I'm working on implementing a RADIUS authentication for wireless access with the following :
- PCs running Windows 7, protocol used is PEAP (without validating the server certificate to make it simple at first),
- AP 1252 configured to use a RADIUS server to authenticate (it's working good with an ACS server 4.2),
- ACS Server 5.1.0.44.5 running as VM connected to an AD domain and working good with VPN connections,
- AD domain running on Windows 2003 Server.
My ACS VM is working good since a couple of months for VPN (RADIUS) and administration (TACACS) remote access, both using Active Directory. Now, I'd like to use it to authenticate people connecting to a 1252 Cisco access point but I'm getting this error "24427 Access to Active Directory failed". I switched from PEAP to LEAP but this is the same.
All I can get running the expert troubleshoot
Investigating failure code: 24427 Access to Active Directory failedChecking if Active Directory is configuredActive Directory is configuredAttempting connection to Active DirectoryConnection to Active Directory was successful.Troubleshooting completed.Click on Show Results Summary to view results.
I followed this guide, at least for the ACS certificate section :
[URL]
So we have multiple ISE Servers with differing personals. I was having an issue with our new ISE setup not identifying AD Group Attributes when using them in Authorization rules. We have 2- 3395 appliances running Admin and Monitoring/Troubleshooting Personas and 2- 3395 appliances running as Policy server personas. We are running v1.1.1.268 with the latest two patches. I was unable to pull Active Directory Group Attributes in any of my Authorization rules. After Resyncing all the boxes with the Primary Administration box I was able to do this. There is no bug listings for this occurrence nor do we have Smartnet to call support for other reasons.
View 3 Replies View RelatedWe currently have an issue with our main ISE. When logged in using the admin account (member of superadmin group) we no longer see the Profiling button/menu and also missing oter options in the GUI. On another standalone ISE we do see al those options?
Both are running on the same software version 1.1.1.268.We are using ISE 3395-K9 appliances
I am trying to upgrade a brand new ISE 3395 from 1.0.3.337 to 1.0.4 (latest). It keeps failing with % Manifest file not found in the bundle Here is the output:
company-ise-01/admin# application upgrade ise-appbundle-1.0.4.573.i386.tar.gpg ftp
Save the current ADE-OS running configuration? (yes/no) [yes] ?
Generating configuration...
Saved the ADE-OS running configuration to startup successfully
Initiating Application Upgrade...
% Manifest file not found in the bundle
[code]...
I can't find anything about this for ISE, although there are a lot of topics for the same error for ACS.
I am having Cisco 3845 series router with c3900-universalk9-mz.SPA.151-4.M2.bin IOS . I want to install new Licence on it for DATA. When i am trying to install licence on it i am facing the error "% Error: License installation failed with error: XML parsing failed".
View 4 Replies View RelatedI've been working on my laptop recently, once finished i turned my computer off like most people do. After turning it back on hours later, i noticed that my laptop was connected to the internet router but had limited access which ment i could'nt get onto the internet ! So when I went onto Network and sharing center and nothing came up apart from ''the dependency service or group failed to start'' ...I don't want to use system restore or reset tools of windows
Current OS: Windows 8 PRO
Model: ASUS K43SV
After I initial MSE with the wizard. MSE take so long to start the service (more than 1 hour) with "Starting MSE Platform, waiting to check the status"Then I decide to reboot the appliance, after that MSE shows the message "Traceback (most recent call last) File "/usr/sbin/yum-updatesd", line 40, in ?import gaminImportError: No module named gaming.
View 7 Replies View RelatedWe are using Catalyst 3750 switch stacks with software 12.2(44)SE. We have two stacks, only one with IP routing enabled.When we try to run an Acquisition Action on this, from Admin> Collection Settings> User Tracking, the system replies with an error "Failed to start acquisition: Device unreachable. Please enter a valid device"device Center reports "success" on all collector status.Acquisition starts successfully when we try with the other stack.With LMS 4.1 demo, users acquisition runs successfully.
View 18 Replies View RelatedMy roommate and I are trying to set up the internet, but my computer won't detect the Ethernet Cable. Whenever I go to Network and Sharing Center and try connecting to the internet, the computer simply says "Windows did not detect any networking hardware", even though the light is clearly on and should be working. The cable is also new so it should be fine. I've also been looking around on the internet a bit, and in trying to fix the problem it looks like some of my Services are turned off, which seems to be causing the problem. However, whenever I try and turn them on, I get an error message saying "The dependency service or group failed to start".
View 5 Replies View RelatedI upgraded CiscoWorks LMS from 3.0 to 3.2 today. Everything worked prior to the upgrade.The upgrade was successful, with no errors, and all services started. check everything and I see no problem. The system creates the file MDCSupportInformation.zip me clean without any content.I add the installation log file;And tell them that after upgrading to 3.2, you carge the following patches:
LMS321-win-CSCtr77570-0.zip,
cm5.2.1-nt-CSCtw88763-1.0.zip,
lms3.2.1-win-CSCts95764-0.zip,
lms3.2.1-win-CSCts82530-0.zip
in that order.He added the logs generated by the LMS services Tomcat and Apache
I have a 3750 stack of 4 switches that was installed about 2 years ago. Recently I was doing some work on the switch and realized that I am unable to save the config. I amobviously concerned that if the power fails or the switch reboots I will be reconfiguring it and that is not something I am interested in doing! [code]
View 3 Replies View RelatedI have done new configuration for CPI 1.2. while i tried to start service i got belw error. [code]
View 3 Replies View RelatedI have a DIR-615 Rev. A1, and i'm trying to set up a DCHP reservation. Whenever I try, I get an error saying my MAC address must start with 00. I'm running Firmware 1.10.
View 1 Replies View RelatedWe are using LMS 3.2.1 with SP1 and Campus Manager 5.2.2.Server runs Windows 2003 R2.Everything runs fine except for User Tracking on two Catalyst 6500 switches running CatOS. These devices are discovered, reachable, SNMP works fine, neighbors seen. But when we try to launch acquisition, the UT utility complains with this error message:"Failed to start acquisition: Device unreachable. Please enter a valid device."When we wanted to add ports via Device Trap Configuration, LMS has fired a different error message: "There are no ports to configure for the selected device(s).Check whether you have selected any router(s)." I have checked the portsData.xml file, which doesn't have any ports included for the two devices: [code] We have tried to exclude / include the switches in the data collection, but that didn't work.
View 3 Replies View RelatedDay before yesterday my Laptop [Dell Studio] has suddenly stopped working and i have to shut it down forcefully. Then i logged in again but my wireless was not working, i have googled the solutions and tried to start the WLAN Autocofig service but its throwing an error : 1053 : The service did not respond to the start or control request in a timely manner.I have Windows 7 installed on my system.Suddenly the speed of my laptop reduced drastically. Now its taking almost 12 mins to start instead of 2 mins.I have also removed some lines from the test files from the registry as mentioned in the below website as a resolution, but its not working.Unable to connect to wireless networks on Windows 7 Enterprise laptop. I dont have OS [Operating system's] CD as it was pre-installed on my laptop when i bought it.
View 2 Replies View RelatedI do not see any start records in Radius Accounting reports but do see only Stop records ?
btw I am running ACS 5.2
I have two ACS v 5.2 (primary and secundary) and some users are in the internal stor and the others are in the AD.The local site topology is like this:
PC - AP - WLC - ACS - AD
Authentication method is PEAP(EAP-MSCHAPv2) and all user have the certificate company installed. The OS in the client users is Windows 7.Users was working fine but some users reports intranet disconnections. I see in the ACS log many "22056 Subject not found in the applicable identity store(s)." and "24415 User authentication against Active Directory failed since user's account is locked out" alarms.I believed it was because user wasn´t in the AD data base, but some times the same user is authenticated successfull and other i see the "22056...." or "24415...." alarms.
I switched the role for ACS primary to works as secundary and we see the same alarms.
In my head office we have Cisco 3845 router.in the router we put the show log command the below error is came..
What is the error??why the error came??
25024684: Feb 29 10:33:13.759 India: %FAN-3-FAN_FAILED: Fan 1 had a rotation error reported.
25024685: Feb 29 10:33:33.759 India: %FAN-3-FAN_FAILED: Fan 1 had a rotation error reported.
25024686: Feb 29 10:33:53.759 India: %FAN-3-FAN_FAILED: Fan 1 had a rotation error reported.
25024687: Feb 29 10:34:13.759 India: %FAN-3-FAN_FAILED: Fan 1 had a rotation error reported.
When I try to log-in to my D-Link DIR-835 Router using IE9, I get an 'Authentication Failed' error. FireFox & Chrome work just fine. what I need to change or fix in IE9 so it will also log-in to my router?
View 13 Replies View RelatedI am running IOS version 8.0(5) in cisco ASA 5520. This issue i am facing is that when the memory utilzation reaches 49 percent, the web-vpn users are not able to login as they are getting a blank page. The only error which is getting in the output " sh mem webvpn allobjects" is ERROR: Memory allocation failed?
View 2 Replies View RelatedI had upgraded the MSE to 7.0.202. Release code. The Upgrade along with the 4 database zips went smooth.But the MSE status shows following
View 2 Replies View RelatedGetting this error on the data center 2581 (12.4(24)T) from a GRE/IPSEC tunnel, remote branch is 2811 running 12.4(25d)
%CRYPTO-4-RECVD_PKT_MAC_ERR: decrypt: mac verify failed for connection id=
The tunnel has been up and working okay for months, nothing has changed on the config and the key is correct. Traffic is following but remote users are complaining of performance issues. A wireshark shows checksum errors and lots of packet resends. Remote ISP has checked the circuit and says its clean.The data centre router has quite a few tunnels but only 1 causing this issue. From the head end router -
sh crypto ips sa | b x.x.x.x
current_peer x.x.x.xport 500 PERMIT, flags={origin_is_acl,} #pkts encaps: 15129, #pkts encrypt: 15129, #pkts digest: 15129 #pkts decaps: 13346, #pkts decrypt: 13346, #pkts verify: 13346 #pkts compressed: 0, #pkts decompressed: 0 #pkts not compressed: 0, #pkts compr. failed: 0 #pkts not decompressed: 0, #pkts decompress failed: 0 #send errors 1, #recv errors 1992
Can a VPN module go bad like this? I've tried disabling the branch onboard engine and using software but it doesn't work.
Whenever I try to goto a webpage within any browser,despite me being connected to my network(though 1 received packet to every 20 or so sent packet ratio) it tells me that DNS lookup failed. I had a similar issue on my other pc that I use more often,though connecting through WIFI momentarily resolved the issue,before I returning to wired,where everything has been fine. My other pc however has no wifi adapter. So ive been stuck.
View 12 Replies View RelatedI have have a XPS L502X. I decided to make a clean installation based on Windows 7 Ultimate.My problem is when I instal the driver for the "Dell Wireless HSPA 5540" it fails with then warning:
"Authentication failed. The .... driver cannot be installed on this computer...."
How to install driver for this ?
I am unable to connect to the internet on my desktop computer. The error message I receive is" Download failed(12007) The sever name or address could not be resolved" I am running windows 7. Hooked up to att uverse. My laptop is working as you can see by sending this message. I have been trying to fix this problem for the last 2 days to no avail. I uninstalled norton hoping it was a firewall problem. On the local area connection it shows IPV4 connedtivety: No Network access.
View 2 Replies View RelatedI have just gone through hours of tech support with my ISP and still cannot seem to get online. Problem is the same as recent posts by jerguy1928, with message "DNS lookup failed...." coming up in Google Chrome. Both IE and FF just say cannot connect.Running Windows 7 on laptop. I have tried alt DNS settings (Google and others), all the CMD suggestions, disabling firewalls etc, etc! Other computer in house connects just fine.Ping works fine. Really, there appears to be no reason to not be able to connect - since I am actually connected!
View 13 Replies View RelatedWhen I try to connect to our domain I get the error message:Changing the Primary Domain DNS name of this computer to "" failed. The name will remain "(name of our domain)" The specified domain either does not exist or could not be contacted.The procedure is the same I've used since Hector was a pup and never had a problem. I can't add users to the domain and can't log on directly to the domain.
View 1 Replies View RelatedI am using URL Snooper to copy URLs from slide share into my hard drive. Although my internet connection is working fine i am getting the message"ERROR:failed to find a suitable network driver". I cannot understand what the problem is" Please assit me in this issu
View 1 Replies View Related