Cisco WAN :: Cat3750 Copy Run Start Error
Jul 4, 2012
I have a 3750 stack of 4 switches that was installed about 2 years ago. Recently I was doing some work on the switch and realized that I am unable to save the config. I amobviously concerned that if the power fails or the switch reboots I will be reconfiguring it and that is not something I am interested in doing! [code]
View 3 Replies
ADVERTISEMENT
Feb 24, 2012
I have a really stupid problem with my RV042. The main logon password has expired but it will not let me change it at all. Basically I try to login but get the error 'The old password has expired. Please change the password'. But with no prompt at all for a new password and just a return to the login page. Tried various different browsers, tried the old default password but nothing will work. There seems to be no way of changing it and I cannot login.Am I missing something glaringly obvious? I really don't want to reset it to default as I have numerous VPN tunnels configured and various other settings.
View 2 Replies
View Related
Feb 20, 2012
I have a 3550 switch that I am trying to upgrade the IOS on.I am trying to copy to a TFTP server.I am receiving a socket error. [code]
View 3 Replies
View Related
Feb 20, 2012
I have a 3550 switch that I am trying to upgrade the IOS on.I am trying to copy to a TFTP server.I am receiving a socket error.I saw that this can be fixed with
Switch#config t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#no service config
Switch(config)#exit
Switch#
00:13:47: %SYS-5-CONFIG_I: Configured from console by console
Switch#reload
I have done this 3 times to no avail.My TFTPd32 server on my pc is working fine.Here is the error
Switch#sh flas
Directory of flash:/
2 -rwx 556 Mar 1 1993 00:33:53 +00:00 vlan.dat
4 -rwx 3775 Mar 1 1993 00:37:54 +00:00 config.text
5 -rwx 24 Mar 1 1993 00:37:54 +00:00 private-config.text
6 -rwx 5687963 Mar 16 2007 01:05:23 +00:00 c3550-ipbasek9-mz.122-25.SEB4.bin
8 drwx 192 Mar 1 1993 00:04:40 +00:00 c3550-i9q3l2-mz.121-22.EA1a
[code]......
View 14 Replies
View Related
Nov 24, 2012
I upgraded CiscoWorks LMS from 3.0 to 3.2 today. Everything worked prior to the upgrade.The upgrade was successful, with no errors, and all services started. check everything and I see no problem. The system creates the file MDCSupportInformation.zip me clean without any content.I add the installation log file;And tell them that after upgrading to 3.2, you carge the following patches:
LMS321-win-CSCtr77570-0.zip,
cm5.2.1-nt-CSCtw88763-1.0.zip,
lms3.2.1-win-CSCts95764-0.zip,
lms3.2.1-win-CSCts82530-0.zip
in that order.He added the logs generated by the LMS services Tomcat and Apache
View 4 Replies
View Related
Mar 8, 2013
I have done new configuration for CPI 1.2. while i tried to start service i got belw error. [code]
View 3 Replies
View Related
Oct 14, 2012
While installing ISE 3395 i am getting error failed to start DB!
Database is not available withintimeout of 240 seconds.this could be reason of incorrect network configuration or lack of resources on the appliance or VM, run the folloing CLI to re-prime database 'application reset-config ise'
View 3 Replies
View Related
Feb 22, 2012
I recently posted this same issue the other day, using TFTPd32. Now i am pretty close to fixing it. I do have a different setup; my pc ethernet port is broken so I am using an ethernet/usb adapter. I am attempting to backup my IOS from a 3550 switch to my PC.
This is the error I am getting. Code...
View 5 Replies
View Related
Jul 20, 2011
DHCP Client and Network Location Awareness aren't working. When I tried to start DHCP Client, I got Windows could not start the DHCP Client service on the Local Computer.Error 5: Access is denied. I checked the dependencies and all of them were on. For Network Location Awareness, I got the error Windows could not start the Network Location Awareness on Local Computer. For more information, review the System Event Log. If this is a non-Microsoft service, contact the service cendor, and refer to service-specific error code -1073741288. One of its dependencies is fine, but I don't know how to check the other two, Ancillary Function Driver for Winsock and NetIO Legacy TDI Support Driver. Also, how do I check the event log?Everything on the list that was said to check is running expect these two the lisie was having problems with. I have not had anything with memory recently and have not been able to successfully go through a system restore. I have tried many of the suggestions and just am not sure what to do anymore. The computer works perfectly fine, minus it cannot get on the internet.
View 1 Replies
View Related
Feb 29, 2012
I have a DIR-615 Rev. A1, and i'm trying to set up a DCHP reservation. Whenever I try, I get an error saying my MAC address must start with 00. I'm running Firmware 1.10.
View 1 Replies
View Related
Apr 11, 2012
Day before yesterday my Laptop [Dell Studio] has suddenly stopped working and i have to shut it down forcefully. Then i logged in again but my wireless was not working, i have googled the solutions and tried to start the WLAN Autocofig service but its throwing an error : 1053 : The service did not respond to the start or control request in a timely manner.I have Windows 7 installed on my system.Suddenly the speed of my laptop reduced drastically. Now its taking almost 12 mins to start instead of 2 mins.I have also removed some lines from the test files from the registry as mentioned in the below website as a resolution, but its not working.Unable to connect to wireless networks on Windows 7 Enterprise laptop. I dont have OS [Operating system's] CD as it was pre-installed on my laptop when i bought it.
View 2 Replies
View Related
Sep 12, 2011
I would like to update the device package for Cat3750. The readme file from update package says that DtShare V1.10 (DtShare.cv50.v1-10.zip) has to be installed first. I have actually DtShare V1.9 installed but there is no DtShare V1.10.
When I execute the device update, than it downloads everytime the DtShare V1.9. My question to Cisco staff and all other CW specialists: How can I become the DtShare V1.10?
View 2 Replies
View Related
Sep 25, 2010
I currently have Netflow enabled on all of my routers in my network. However, I have a Cat3750, which does not support Netflow. The 3750 is at a larger remote site and I need visibility into the traffic that is traversing internal to that switch. All VLANs are configured on the 3750. I have an extra Cisco router, which I have theorized I could use as a Netflow probe.
The 2811 Router has to FastEthernet ports.F0/0 would be configured with no IP Address and would be connected to the 3750 on G0/1 with no VLANs configured.F0/1 would be configured with a static IP and connected to the 3750 on port G/02 with the appropriate VLAN to ensure network connectivity.
On the 3750, configure a monitor session with a destination of Interface G0/1.On the 2811, configure netflow to sent to the Netflow server and set F0/0 for ip flow ingress.Obviously, it doesn't work. But I cannot figure out why.
View 3 Replies
View Related
Jun 5, 2012
I've just noticed an error I've never seen before in our switch logs. We have a stack of 6 Cat3750G-48TS-E switches. The first two in the stack have been up for just over a year and I've only just noticed this error. Thus far, I haven't noticed any symptoms - I just stumbled upon this error while checking for something else.
As far as I can tell, this has only popped up once and it was 2 days ago. Unfortunately, due to an incorrect firewall rule, our syslogs were not getting to our syslog server so I don't have any historical logs to check against, but it hasn't happened since.
The error I've seen is as follows:-
Jun 5 17:04:03.288: * ManagementInterfaceInitialized exception in port-asic 0 (N16FujitsuSwitch.com.au-2)
Jun 5 17:04:03.288: ***********************************************************
[Code].....
View 5 Replies
View Related
Feb 22, 2012
I have encountered some weird issue on our Cat3750 running as DHCP Server.I have excluded 5 IP addresses only on the running configuration. [code]
View 1 Replies
View Related
Jul 19, 2011
I am using TFTPD32 to upgrade the IOS on a router. When I type in the commands copy tftp flash and enter all the necessary information, the router sits for a minute or so and then times out. There is no entry made in the log when it times out. copy flash tftp yields the same result. The fa 0/0 interface and the TFTP server are both on the same subnet and can successfully ping one anothe
View 16 Replies
View Related
Jun 20, 2012
I have 3 Cisco 2600 routers with the same IOS and memory.One of them has CME...
What would be the best way to copy the CME from the one router over on the other two?Backup my FLASH to my TFTP and then restore to the other two routers?
View 1 Replies
View Related
Mar 22, 2012
I am trying to map network and copy files to D:BackupSql_Backup?How can I sue this with spaces in my folders
net use R: \000.00.0.00Program FilesMicrosoft SQL ServerMSSQLBACKUP"
cd
echo off
R:
cd
Xcopy . /D /I /F /E /Y D:BackupSql_Backup
net use R: /delete /y
exit
View 5 Replies
View Related
Oct 12, 2011
I have a network using windows home server 1, with 3 computers hooked up to it. Two of them work fine but the 3rd computer cannot successfully copy a file to the network. However, I can copy a file from the network to computer 3.This started suddenly about a week ago and there were no driver updates or anything changed that would cause this. When I copy a file from the network to computer 3 I get about 80mb/second. When I try the reverse, it pauses and after about 5 seconds I get a message saying:There is a problem accessing \serverserverfolder. Make sure you are connected to the network and try again.If I try to copy a small file of a few megabytes it will copy though.
View 5 Replies
View Related
Jun 27, 2011
I need to do a backup on our laptop prior to beginning the malware removal process. I need to move 22GB+. There is plenty of room on our desktop to store the files.Would it be best to use file sharing between the 2 PCs? They are both USB connected to the same router. Or, is it possible to transfer the files by connecting them directly to each other via USB?
View 5 Replies
View Related
Aug 7, 2011
I have seen similar questions but with not a lot of answers for the ASA platform. As the title states, What procedures can I use to copy a pre-existing configured CISCO ASA 5520 to a brand new CISCO ASA 5520. I have found a URL that seems to answer some questions but not all. [URL]
The URL talks more about the PIX's than the ASA
Is there any documentation or shorter procedures for product specific on the 5520?
View 1 Replies
View Related
Mar 28, 2011
The FTP server log shows no hits, from 192.168.1.4 I can telnet to 5505 no problem.
Doing everything on inside interface eth0/1, ftp server shows up and arp table of 5505 has correct mac for 192.168.1.4
ciscoasa# copy ftp://bob@192.168.1.4/asa841-k8.bin disk0:
Address or name of remote host [192.168.1.4]?
Source username [bob]?
[Code]...
View 2 Replies
View Related
Apr 5, 2011
After the installation LMS 4.0 I make Upgrading on LMS4.0.1. The process remains stand with the message "File Copy in progress..." during several hours. After the Reboot of the server it points me Cisco Works again with LMS 4.0 starts.OS Version: Windows 2008 R2
View 14 Replies
View Related
May 26, 2013
I have a new ASA 5505 we have in production the same model.
So I copy and paste the same config bot ASA have the same IOS version 8.4(3)
But the VPN is not working. is because of this ? ikev1 pre-shared-key *****
When I copy paste the config the pass is still like this ****.
How can I copy my config to the new device withouth introduce the pass again.
View 6 Replies
View Related
Feb 22, 2011
When I try to import configuration from the controller 4400 to my WCS it gives the following message:
Status Refresh succeeded but some records were dropped because their key fields failed validations.
When i see the config in the WCS, all of my light access points are not on it. I check for the logs and this is What I get: (its a lot of info, so I am putting an example!)
02/23/11 14:18:46.784 ERROR [general] [TP-Processor7] THROWcom.cisco.server.common.errors.InternalException: [COMMON-1]: COMMON-1com.cisco.server.common.errors.ObjectNotFoundException: COMMON-
[code]......
View 3 Replies
View Related
Jan 8, 2013
I just got a brand new ASA 5550, i configured the port g0/0 on asa with an ip address 192.168.10.1 then configure my computer with ip 192.168.10.2 and default gateway is 192.168.10.1. I'm able to ping the asa from my computer. I remote to ASA thru the console port and try to copy iOS from flash to my pc but it doesn't work.
Cisco asa# copy flash tftp://192.168.10.2/asa804-k8.bin
Source file name []? asa804-k8.bin
Address or name of remote host [192.168.10.2]?
Destination file name [asa804-k8.bin]?
Writing file tftp://192.168.10.2/asa804-k8.bin...
!%Error writing tftp://192.168.10.2/asa804-k8.bin (Timed out attempting to connect)
Cisco asa#
View 3 Replies
View Related
Feb 12, 2012
How do i copy file of a remote computer to another remote computer through cmd
View 1 Replies
View Related
Mar 26, 2011
how to copy files from hard disk to hard disk through cmd
View 3 Replies
View Related
Mar 9, 2013
I re-installed Windows XP on a dual boot with Windows 7 but I have no access to the Internet.There is no problem with Windows 7. I have Wi-Fi with an ethernet connection.What am I missing? Without Internet access I am unable to activate my copy of Windows XP
View 5 Replies
View Related
Jul 18, 2011
I have an issue installing LMS 4.0.1. LMS 4.0.1 installation is left with "file copy in progress". We waited for few hours and the process java.exe taking the cpu (among 45%).After few tried, same problem occurs ...Antivirus is correctly disabled (I checked the process), and the installation file was decompressed.LMS 4.0 was correctly installed using R2 patch on Windows 2008 Server R2.
View 2 Replies
View Related
May 2, 2013
how to copy a cisco ios image from a 3750 to my pc so that i can use it to upgrade a switch on my desk.
View 3 Replies
View Related
Oct 29, 2012
I made an ASDM upgrade for one of my two CISCO ASA 5520. If I copy a file to the primary ASA's flash, is there any command I can run on the primary ASA to copy a file to the secondary ASA?
View 1 Replies
View Related
Jan 4, 2012
i have 2811 router and i am coneccted via concole so i want to copy the 2811 ios to my PC is that possible?
how or give my the right decument to do this.
* idon't want to use TFTP becuse i have no ethernet connection to the router(only concole)
View 5 Replies
View Related