I have 3 Cisco 2600 routers with the same IOS and memory.One of them has CME...
What would be the best way to copy the CME from the one router over on the other two?Backup my FLASH to my TFTP and then restore to the other two routers?
I am sitting on Internet and want to copy IOS Image to router. I can SCP, itu authenticated to Router but ends with a message "host is not communicating for more than 15 seconds".
Router : Cisco 2821
Current IOS: (C2800NM-ADVENTERPRISEK9-M), Version 12.4(24)T1.
I have two Routers (C1812 & C1841) each having different version of IOS images. I was wondering if its possible to copy IOS image from flash of one Router and use it to upgrade another.
View 2 Replies View RelatedI am using TFTPD32 to upgrade the IOS on a router. When I type in the commands copy tftp flash and enter all the necessary information, the router sits for a minute or so and then times out. There is no entry made in the log when it times out. copy flash tftp yields the same result. The fa 0/0 interface and the TFTP server are both on the same subnet and can successfully ping one anothe
View 16 Replies View RelatedI have a cisco 877 router connected to our adsl broadband at our head office. I have managed to set this up with Nat and DHCP all working to let multiple users access the internet through our single static ip supplied by the ISP lets say the ip is 1.2.3.4.Our internal network is 192.168.1.0 255.255. 255. 0.I have a draytek vigor 2600 at a branch office set up the same with a static ip addresss supplied by the ISP lets say the ip is 5.6.7.8.The internal network is 192.168.4.0 255.255.255.0
I am trying to set up a VPN between the head office and branch office so the branch office users can connect to our internal server(lets say ip is 192.168.1.2) to receive group policies,access files and also telnet into our database server(lets say ip is 192.168.1.3).I have attached a sort of running config that i have pieced together from bits i have read on this site and others. I have tried these settings and other permutations of these settings but i cant seem to establish a tunnel even though when i show int tunnel0 on the router it says tunnel is up and line protocol is up, if i show ip route it shows that there is an ip address for the tunnel and that is about it(No vpn light on).
If it makes sense and that I have entered the right information? I have highlighted the parts i am not sure about in red(Quite a bit and obviously not the exact settings but what i think it should be). Once all the settings are correct on the cisco will it automatically establish the vpn or do i have to dial it from the draytek.
i want to configure the router for internet access for hosts this is the my pub ip x.x.x.174 and mask 255.255.255.252 this is isp given subnetmask internal ip range is x.x.x.20-x.x.x.254
View 1 Replies View RelatedI have a 2801 running c2801-spservicesk9-mz.124-3g.bin According to the Cisco IOS MIB locator the image supports OLD-CISCO-SYSTEM-MIB I have tried .1.3.6.1.4.1.9.2.1.55 etc to set server IP address and the filename string but without any luck.e.g.
Reason: (noSuchName) There is no such variable name in this MIB.
Failed object: iso.3.6.1.4.1.9.2.1.55.a.b.c.d (where a.b.c.d is the server IP)
I have also tried the method similar to that for Cat 3550 switches where you create a table of entries to define the transfer paramaters then activate the transfer (I think the CISCO-CONFIG-COPY-MIB)
e.g.
[URL]
C:>snmpset -v 1 -c private <device name> ccCopyProtocol.<random number> integer 1 ! 1 = tftpccCopySourceFileType.<Random number> integer 1 ! 1 = networkFileccCopyDestFileType.<Random number> integer 3 ! 3 = startup & 4 = runningccCopyServerAddress.<Random number> ipaddress "<server ip address>"ccCopyFileName. <Random number> octetstring "<file name>"ccCopyEntryRowStatus.<Random number> integer 4 ! 4 = createAndGo, or 1 = Active
To write net have the source as running (4) and the dest as network (1)
ccCopySourceFileType.<Random number> integer 4
ccCopyDestFileType.<Random number> integer 1
Clean up at the end - destroy .14 with the value of 6.
example output : -
-- earlier output omitted --
Error in packet.
Reason: (noSuchName) There is no such variable name in this MIB.
Failed object: iso.3.6.1.4.1.9.9.96.1.1.1.1.4.111
Error in packet.
[code]...
I want upgrade IOS on my 7206VXR from 12.4(12c) to 15.1(4)M5 , but the CF card only 64M.
-NAME: "disk2", DESCR: "64MB Compact Flash Disk for NPE-G1"
-Router#show bootvar
BOOT variable = disk2:c7200-jk9s-mz.124-12c.bin,15.1(4)M5 is almost 40M. So there is not enough space.I want to ask is it ok if I upgrade with normal precedure , With the command " copy tftp: disk2: " ?Does the router will automatically delete the older IOS first and then copy into the new one ? Or Is there something I should pay attention first ?
When I try to copy ios to one flash in router 2801, I receive the message of of insufficient memory, and have the follow out in the next command: [code] This product contains cryptographic features and is subject to UnitedStates and local country laws governing import, export, transfer anduse. Delivery of Cisco cryptographic products does not implythird-party authority to import, export, distribute or use encryption.Importers, exporters, distributors and users are responsible forcompliance with U.S. and local country laws. By using this product youagree to comply with applicable laws and regulations. If you are unableto comply with U.S. and local laws, return this product immediately.
View 6 Replies View RelatedI have an 877W router that I would like to have a 2nd pre-configured backup for. I was thinking of getting another 870 series (probably an 877) router, as the more expensive wireless option is not actually required. Am I right to assume that I could simply copy the contents of my current config.txt file onto the second router?
View 4 Replies View RelatedHow to know the serial 0 or 1 (to v35 modem)was good or not ? is there any tool (software) or hardwire jumper to simulate loop back ?
View 12 Replies View RelatedHow to know the serial0 or 1 (to v35 modem)was good or not ? is there any tool (software) or hardwire jumper to simulate loop back ?
View 4 Replies View RelatedI have cisco 2600 router. The problem is my router ios has been crashed and i unable to use any mode on my router. I need to install new ios. How can i install or upgrade new ios step by step.
View 1 Replies View RelatedCurrently I'm using Cisco VPN client software to connect to a remote IPSec server on the workstations. I want to to configure IPSec client on Cisco 2600 router which connects to the remote IPSec server so the workstations can access VPN subnet without using VPN software. how to configure IPSec client on the router?
View 20 Replies View RelatedWe have an old Cisco 2600 series router, running a single T-1 line, AT&T is the carrier. Very standard stuff.
The T-1 works perfectly on the old router. Cisco 2600 with a WIC-1DSU-T1 card. We have a brand new 2911 router with a VWIC3-1MFT-T1/E1 card in it. The circuit runs 100% clean and trouble free on the old router. When I plug it into the new router, it shows up/up but has a massive number of errors on the line, and the circuit is not usable. There are no timing slips or anything like that.
I have another site using the same router and card with the same configuration on that T-1 and it works perfectly. Zero errors. This site (in a different city) is totally slammed with errors. We already replaced the T-1 card and still have the exact same issue.
I've actually been doing this a long time, and I've tried all of the usual things, adjusting line build out, changing clock source, checking and re-checking configs. Nothing seems to reduce the error rate.
I personally think it has something to do with the Smartjack. Like maybe their LBO is too high or too low, and the old router card was more/less sensitive than the new one?
This is a layer 1 issue and is not defective hardware or defective configuration. I am looking for T-1 insights or bugs/issues.
I've rolled back my E4200 router to the old firmware 1.0.0.1, then set up a media server.It generally works (e.g. it streams pre-existing media files to other devices). I can copy to this external drive small (say, < 1 MB) files. The drive has enough free space. However, I cannot copy to this external drive large (e.g. 700 MB) files.
View 5 Replies View RelatedI've been experiencing a strange, repeatable behavior with my Linksys E1000. I have several wireless and wired devices connected to my E1000:
Wired: TivoHD, Sony BluRay Player, Sony TV, Windows XP Wireless: Lenovo Laptop (Windows 7), HP Laptop (Windows 7), 3 iPods, 2 iPhones
When I try to copy large files (~ 4GB) from my (wired) Windows XP box to either of my (wireless) laptops, the Linksys drops my WiFi network -- but the wired connections continue to work (including internet access). Copying the same/similar file from a WiFi device to a wired device appears to work correctly, as does copying from WiFi to WiFi.
To be clear, my WiFi network "disappears" -- it is no longer listed as an available network (as opposed to just dropping internet connectivity for WiFi). Unplugging the router and plugging it back in brings my WiFi network back up.
I have been able to repeat this issue with multiple files over the course of several weeks, and it happens about 75% of the time (i.e., I am occassionally able to complete a file copy from wired LAN to WiFi).
A little bit of background: I resurrected an old Windows XP box and am using it for shared network storage. I copied about 400 GB of files from my laptops to the XP box (WiFi to wired) with no issues at all. Pulling the same files back from XP to my laptops (wired to WiFi) has been causing the issue described above.
I have a cisco 2600 router with 4A/S module, can it become the terminal server? If yes, which kind of octal cable should I choose to connect to other cisco routers console ports?
View 0 Replies View Relatedtrying to establish a connection on an ibm 3745 controller via two IBM 5822 modems to a cisco 2600 router using sdlc encapsulation secondary bridging data from the serial port to the E/Net port to run the 3270 client ???
View 19 Replies View Relatedour office has cisco 2600 series router. i want to know on how i can configure it to connect to another router in a different site.
View 9 Replies View RelatedI am asked to implement the security in campus Network. i.e. In this network we want to block some websites, We don't want to use any 3rd party software or proxy server and content filtering module to block theset.my router IOS is advance securityk9 How to block the website in a Cisco 2600 series router by using the command. What is the access list we need to use to block.Assume we want to restrict,
[URL]
Here we are using Cisco 2600 series router and 2900 series switch. In router we are using the2Mb lease line link
I am connecting a 2600 router to an ISP. Interface 0/0 is connected to the ISP using DHCP. Interface 0/1 is connected to the inside providing DHCP services to the inside. At least it should only be providing DHCP services to the inside. I also have a public static IP that is NAT to a private static IP. Everything is working except the computer on the static IP. From the router I am able to ping inside and out from each interface. I am able to ping both interfaces of the router from the computer on the static IP but I cannot ping outside the router. If I do a debug all I see a reject for the gateway of the static IP but it has “mobile IP” in the text string. Not sure what mobile IP is relating to. Networks are as follows:
0/0 DHCP 10.X.X.X
0/1 192x.x.x
Static 75.X.X.X
no ip dhcp use vrf connected
ip dhcp excluded-address 192.X.X.1
ip dhcp excluded-address 192.X.X.2
ip dhcp pool CLIENT
[code]...
I have a 2600 router and im trying to set it up for SDM. The crypto command is not there. What do i do?
show version
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-J1S3-M), Version 12.3(15b), RELEASE SOFTWARE (fc1 )
Copyright (c) 1986-2005 by cisco Systems, Inc.
Compiled Thu 25-Aug-05 13:38 by ssearch
Image text-base: 0x80008098, data-base: 0x81A255C4
[code]....
How do I save/copy all of the router configuration entries onto a memory/flash usb drive? I did not configure the router myself (out of town when purchased). I have already downloaded the manual for that router and I want to understand exactly what she (person who configured router) did and identify any mistakes she might have made. Once downloaded, I assume I can print out all configuration settings.
View 3 Replies View RelatedI've currently got a WRT54G and have an opportunity to buy a WRT54GS. The problem is that the seller of the WRT54GS has lost the Set-Up Wizard CD & Hard Copy Quick Installation Guide. Obviously I have these items already with my WRT54G. My question is this. Are these items different for the WRT54G or will the stuff I already have for the WRT54G "work" for the WRT54GS.
View 5 Replies View RelatedSince the EA4500 automatically updates via the Cisco Connect Software, does a copy of the firmware file get saved to the local computer?
View 1 Replies View RelatedHow to configure HSRP in techroutes 2600 series router and aaa authentication
View 2 Replies View RelatedI have Cisco 2600 series Router which has only 32 MB flash memory. I tried to load IOS image in that but image size is 29 Mb in compressed form. The minimum i found is 5 MB in compressed form but it is missing so many commands. that in 32 MB flash, how can I load image which has almost all the commands.
View 3 Replies View RelatedI just configured cisco 2600 as TS for remote dial in via USRobotics modem, I can dial into router, but its not accepting my key board input.
View 2 Replies View RelatedI have a 2600 Router series and I cannot remember the Password. I have tried following web pages that state to use control Break on the boot up but its not working.can reset that pw and write erase my configuration file?Here is my boot up. I have tried hitting control break at the very beginning over and over and then again when at the cold boot it has not worked....
System Bootstrap, Version 12.2(7r) [cmong 7r], RELEASE SOFTWARE (fc1)Copyright (c) 2002 by cisco Systems, Inc.C2600 platform with 131072 Kbytes of main memory
program load complete, entry point: 0x80008000, size: 0x1c9468cSelf decompressing the image : ######################################################################################################################################################################################################################################################################################################################################################################################################################################################################## [OK]
Smart Init is enabledsmart init is sizing iomem ID MEMORY_REQ TYPE00036A 0X000B3B80 C2610XM Single Fast Ethernet 0X00098670
[code]....
I have recently made a WAN change from T1 to fiber and my Cisco 2600 series router no longer needs to connect over the Serial T1 card. The Serial connection also provided a few voice channels for the old phone system that are no longer needed. I need to keep Main Cisco 2600 router in place because I have many network devices that use it as the gateway instead of my firewall. I will not require the second subnet for Offsite Cisco 2600 anymore either. commands that will be required to remove all instances of the Serial connection and Offsite Cisco 2600. I have included the config of the Main Cisco 2600 below. [code]
View 1 Replies View RelatedI have a cable modem with my 2600 Router and i have a little speed problem when I'm going out to the web via my F0/0.. according to regular speed test sites my speed is around 20mbps but when i hook up to my modem directly i get a solid 40mbps.. now I've changed my Cat 6 cable from my modem to my router and this are my settings in the router.
[Code] ...........
I see some drops and lost carriers but not sure what those might mean?
- How can I connect an old 2600 router to a linksys WRT54G2. to access the internet. I think it is not possible
- What device do i need to be able to do it
