Cisco WAN :: 2600 Remove Serial T1 Card From Router Config
Jul 23, 2012
I have recently made a WAN change from T1 to fiber and my Cisco 2600 series router no longer needs to connect over the Serial T1 card. The Serial connection also provided a few voice channels for the old phone system that are no longer needed. I need to keep Main Cisco 2600 router in place because I have many network devices that use it as the gateway instead of my firewall. I will not require the second subnet for Offsite Cisco 2600 anymore either. commands that will be required to remove all instances of the Serial connection and Offsite Cisco 2600. I have included the config of the Main Cisco 2600 below. [code]
View 1 Replies
ADVERTISEMENT
Aug 6, 2012
On a number of 6500 chassis it appears that linecard 3 did exist at somepoint, but was removed.Problem is that when issuing the 'show int desc' or 'show ip int brie' the ports for the still appear, and indeed same with 'show run' and 'show conf'.
View 1 Replies
View Related
Dec 29, 2012
How to know the serial 0 or 1 (to v35 modem)was good or not ? is there any tool (software) or hardwire jumper to simulate loop back ?
View 12 Replies
View Related
Apr 11, 2006
How to know the serial0 or 1 (to v35 modem)was good or not ? is there any tool (software) or hardwire jumper to simulate loop back ?
View 4 Replies
View Related
Jan 10, 2012
My network generally runs older routers (2600 series) with 16 port switch modules (NM-ESW-16). This has always worked great since I can configure the router and the switch ports on the fly, making changes to either as necessary. Well I am upgrading to 2811 routers, and we wanted to get gigabit ethernet ports on our switch modules. I think I made an error when I purchased a few of these switch modules: NME-16ES-1G.
The first problem, is that the switch ports don't even show up on the router config, I have to establish a session into the switch, (And I can't seem to get back to the router unless I manually switch off power and restart). I don't like this type of switch module, it's like I'm running a completely separate device, and while having a layer 3 switch is cool, It doesn't let me setup routing protocols so I don't like doing it this way. I want to go back to using a switch module that simply adds a ton of ports to my router like the NM-ESW-16. (Note: The NM-ESW-16 does actually work in the 2811 and would be perfect if it were Gigabit speed.)
The seconds problem is that the NME-16ES-1G isn't actually a Gigabit switch. It has a single gigabit port, but the 16 ports are all Fastethernet, and not gigabitethernet. So ideally, I am looking for a switch module that I can fully configure from the router interface that has 16 gigabitethernet ports, and works with a 2811. IE I want to do this. [code]
View 4 Replies
View Related
Mar 17, 2013
i have a simple router on a stick config which is providing dhcp to a customer SSID. however i don't want employees to stay on it and eat the band width since its open. the lease is set to an hour, is there anyway that i could set it so that once your lease expired it can't be renewed for 4 about 8 hours? I am using a cisco 2600 router in this setup.
View 1 Replies
View Related
Feb 12, 2013
I need config mi own Cisco Router 2600 and permit to External Internet my Samsung DVR SDE-4001
View 3 Replies
View Related
Jun 14, 2011
From all of the documentation I am seeing, the 2911 does not support the NM-E3/T3 serial card.
View 16 Replies
View Related
Feb 8, 2012
How do we find out the serial no. for a CIP card on a cisco 7500 router.
View 1 Replies
View Related
Mar 26, 2012
I have existing cisco 2811 (Version 12.4(3c)). I try to add a HWIC serial card into the router but the new HWIC is not detected. There is no new interfece shows up when i do show run. This HWIC is a new card just bought it.
View 7 Replies
View Related
Mar 7, 2012
Is it necessary to remove the card from the camera to manage (view, edit, delete) the recordings?
View 2 Replies
View Related
Apr 17, 2012
If i connected the latop to brand new out of the box ASA 5505 through consloe cable and i have a config file on this laptop from other ASA5505, is there anyway i can upload that config file into startup-config of this new ASA5505 through console cable, without using TFTP or FTP?
View 5 Replies
View Related
Nov 15, 2009
I have a Cisco 2811 router and when I turn of the router the running config is lost. I have to the following to get the router running of the start-up config settings.
router#copy start-up running-config
View 9 Replies
View Related
Jul 13, 2011
I have a cisco 877 router connected to our adsl broadband at our head office. I have managed to set this up with Nat and DHCP all working to let multiple users access the internet through our single static ip supplied by the ISP lets say the ip is 1.2.3.4.Our internal network is 192.168.1.0 255.255. 255. 0.I have a draytek vigor 2600 at a branch office set up the same with a static ip addresss supplied by the ISP lets say the ip is 5.6.7.8.The internal network is 192.168.4.0 255.255.255.0
I am trying to set up a VPN between the head office and branch office so the branch office users can connect to our internal server(lets say ip is 192.168.1.2) to receive group policies,access files and also telnet into our database server(lets say ip is 192.168.1.3).I have attached a sort of running config that i have pieced together from bits i have read on this site and others. I have tried these settings and other permutations of these settings but i cant seem to establish a tunnel even though when i show int tunnel0 on the router it says tunnel is up and line protocol is up, if i show ip route it shows that there is an ip address for the tunnel and that is about it(No vpn light on).
If it makes sense and that I have entered the right information? I have highlighted the parts i am not sure about in red(Quite a bit and obviously not the exact settings but what i think it should be). Once all the settings are correct on the cisco will it automatically establish the vpn or do i have to dial it from the draytek.
View 4 Replies
View Related
Mar 4, 2012
i want to configure the router for internet access for hosts this is the my pub ip x.x.x.174 and mask 255.255.255.252 this is isp given subnetmask internal ip range is x.x.x.20-x.x.x.254
View 1 Replies
View Related
Jun 20, 2012
I have 3 Cisco 2600 routers with the same IOS and memory.One of them has CME...
What would be the best way to copy the CME from the one router over on the other two?Backup my FLASH to my TFTP and then restore to the other two routers?
View 1 Replies
View Related
Jul 11, 2012
Have been battling a router connection to new ATT t1 connection. Router was configured and sent from sister company to this new location. We have had ATT tech test circuit and it tests good, had cat5 cable tested from ATT to router, it tests good. I continue to get serial up/ line protocol down status though and cant communicate to it from wan.
View 4 Replies
View Related
Jan 11, 2012
I have cisco 2600 router. The problem is my router ios has been crashed and i unable to use any mode on my router. I need to install new ios. How can i install or upgrade new ios step by step.
View 1 Replies
View Related
Jan 16, 2013
Currently I'm using Cisco VPN client software to connect to a remote IPSec server on the workstations. I want to to configure IPSec client on Cisco 2600 router which connects to the remote IPSec server so the workstations can access VPN subnet without using VPN software. how to configure IPSec client on the router?
View 20 Replies
View Related
Jul 23, 2012
We have an old Cisco 2600 series router, running a single T-1 line, AT&T is the carrier. Very standard stuff.
The T-1 works perfectly on the old router. Cisco 2600 with a WIC-1DSU-T1 card. We have a brand new 2911 router with a VWIC3-1MFT-T1/E1 card in it. The circuit runs 100% clean and trouble free on the old router. When I plug it into the new router, it shows up/up but has a massive number of errors on the line, and the circuit is not usable. There are no timing slips or anything like that.
I have another site using the same router and card with the same configuration on that T-1 and it works perfectly. Zero errors. This site (in a different city) is totally slammed with errors. We already replaced the T-1 card and still have the exact same issue.
I've actually been doing this a long time, and I've tried all of the usual things, adjusting line build out, changing clock source, checking and re-checking configs. Nothing seems to reduce the error rate.
I personally think it has something to do with the Smartjack. Like maybe their LBO is too high or too low, and the old router card was more/less sensitive than the new one?
This is a layer 1 issue and is not defective hardware or defective configuration. I am looking for T-1 insights or bugs/issues.
View 1 Replies
View Related
Nov 1, 2011
I just finished setting up a bundle of (2) T1's in a multilink bundle and I'm having issues with one of the T1's not wanting to join the bundle.
The router I'm using on the remote office location is a 3620 router running code c3620-i-mz.121-1c.bin
The campus router which is a 7206 is setup the same exact way with multilink 240 and like I've said, serial 0/0 is joined to the bundle just fine, so we are running off one T1 connection.
The serial interface that is not working is: serial 0/1
Here is a show-run:
interface Multilink240
ip address 172.18.xxx.xxx 255.255.255.252
ip route-cache flow
ip ospf network point-to-point
service-policy output PhonesFirst
ppp multilink
[code].....
View 3 Replies
View Related
Jul 11, 2011
I have a cisco 2600 router with 4A/S module, can it become the terminal server? If yes, which kind of octal cable should I choose to connect to other cisco routers console ports?
View 0 Replies
View Related
Jun 5, 2011
trying to establish a connection on an ibm 3745 controller via two IBM 5822 modems to a cisco 2600 router using sdlc encapsulation secondary bridging data from the serial port to the E/Net port to run the 3270 client ???
View 19 Replies
View Related
May 17, 2012
our office has cisco 2600 series router. i want to know on how i can configure it to connect to another router in a different site.
View 9 Replies
View Related
Dec 6, 2010
I am asked to implement the security in campus Network. i.e. In this network we want to block some websites, We don't want to use any 3rd party software or proxy server and content filtering module to block theset.my router IOS is advance securityk9 How to block the website in a Cisco 2600 series router by using the command. What is the access list we need to use to block.Assume we want to restrict,
[URL]
Here we are using Cisco 2600 series router and 2900 series switch. In router we are using the2Mb lease line link
View 6 Replies
View Related
Oct 25, 2012
I am connecting a 2600 router to an ISP. Interface 0/0 is connected to the ISP using DHCP. Interface 0/1 is connected to the inside providing DHCP services to the inside. At least it should only be providing DHCP services to the inside. I also have a public static IP that is NAT to a private static IP. Everything is working except the computer on the static IP. From the router I am able to ping inside and out from each interface. I am able to ping both interfaces of the router from the computer on the static IP but I cannot ping outside the router. If I do a debug all I see a reject for the gateway of the static IP but it has “mobile IP” in the text string. Not sure what mobile IP is relating to. Networks are as follows:
0/0 DHCP 10.X.X.X
0/1 192x.x.x
Static 75.X.X.X
no ip dhcp use vrf connected
ip dhcp excluded-address 192.X.X.1
ip dhcp excluded-address 192.X.X.2
ip dhcp pool CLIENT
[code]...
View 2 Replies
View Related
Jul 8, 2012
I have a 2600 router and im trying to set it up for SDM. The crypto command is not there. What do i do?
show version
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-J1S3-M), Version 12.3(15b), RELEASE SOFTWARE (fc1 )
Copyright (c) 1986-2005 by cisco Systems, Inc.
Compiled Thu 25-Aug-05 13:38 by ssearch
Image text-base: 0x80008098, data-base: 0x81A255C4
[code]....
View 3 Replies
View Related
Mar 6, 2011
I want to remove the DD-WRT firmware from my router.It is a TP-LINK TL-WR740N V2.1 router.I want to set it back to its original firmware.
View 1 Replies
View Related
Jan 25, 2011
I've been noticing a Belkin router on my network for a while now and just yesterday another Linksys router as join the party, causing havoc on my connection speed!
The strange thing is that I'm the only one seeing them through Norton on my laptop, all other computer on my home network is not detecting them. could this mean that someone is monitoring me? is possible? If I move permanently to Ubuntu linux would the problem go away? OR will they still be able to connect and monitor me?
View 6 Replies
View Related
Oct 24, 2011
How to remove password from netgear router?
View 1 Replies
View Related
Dec 25, 2011
I have put my password in wrong on my new laptop and can't connect.
View 1 Replies
View Related
Aug 11, 2011
How do I remove the existing antenna from my N+ router...?
View 3 Replies
View Related
Aug 21, 2009
On the WAN port, there are 4 pins that are traced to the internal serial traces. Where can we get the cable that will fit into the WAN RJ-45 port and have a serial connector on the back end. It may be called a Cisco Debug Adapter, but we haven't been able to find?
View 9 Replies
View Related
