I have a cisco 2600 router with 4A/S module, can it become the terminal server? If yes, which kind of octal cable should I choose to connect to other cisco routers console ports?
View 0 RepliesI have a 2611XM that I am using as a terminal server for my lab setup. Async is using octal cables. It works great with routers of all different models, but when I connect a switch of any model, it does not work. The connectivity LEDs don't even light (they do for the routers). The switches in question are 3750s and 3560s.
I have tried straight through from the octal cable to the console port of the switch, as well as a rollover with a converter, no luck. This does seem to be independent of configuration on the console port - even before the console port of the routers were properly configured, I at least had indication of physical connectivity.
Any example of router config for a terminal server.In fact I need a configuration for a router with multiple, low speed, asynchronous ports that are connected to other serial devices, for example,modems or console ports on routers or switches.With this router I would like to use a reverse telnet to connect with my devices using the serial connection.I find many examples on the Cisco web site but none with my router hardware configuration.My router is a 3620 router with a 8 port async (NM-8A/S) network module and I would like to use the 8 serial interfaces, each of them connecting a serial device.
Here is the show run and show ver :Router#show ver Cisco Internet work Operating System Software IOS (tm) 3600 Software (C3620-I-M), Version 12.3(25), RELEASE SOFTWARE (fc1)Copyright (c) 1986-2008 by Cisco Systems, Inc.Compiled Mon 28-Jan-08 20:16 by alnguyen
ROM: System Bootstrap, Version 11.1(19)AA, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1) Router up time is 1 minute System returned to ROM by reload System image file is "flash:c3620-i-mz.123-25.bin"
[Code]...
I am planning to have 2600 routers with Hardware compression module to accelerate the application performance and to optimize the wan bandwidth.I checked it 10 times optimize the bandwidth. Any pros and cons of these module.I searched in web but didn't get exact points.
View 1 Replies View RelatedWhat command sequence disconnects you from a TS session? My setup is as followsr1 > TS > 2009-2621XM 2010-3825-R1 2011-3825-R2I can connect from the TS to any of the devices. The issue is that I am telnet'd to r1 and from there telnet'd to the TS. So when I type "Crtl+Shft+6, x" I go directly back to r1 and not the TS. Furthermore if I resume the session on r1 the TS is still connected to whatever session I was in prior to disconnecting. I've experimented with the disconnect and escape characters but I'm at a loss what it is that changes this.
View 4 Replies View RelatedWe have the 16-port (NM-16A) and 32-port (NM-32A) asynchronous (async) network modules which provides 16 or 32 EIA/TIA-232 (formerly know as RS-232) data terminal equipment (DTE) serial interfaces at speeds up to 134.4 kbps . Few of the interfaces are connected to the console of cisco switches and routers , now we need to know that the remaining interfaces can be connected to console ports of devices other then cisco Systems to manage them , Will it work with them ?
View 0 Replies View RelatedSince Cisco 2511 is out of sale now and Cisco 1900 series are recommended to replace for the purpose of terminal/comm server. How to configure terminal server on HWIC-8A module?
View 3 Replies View RelatedI want to build up cisco 3800 series router as terminal server , i have Asycs 32A module in cisco 3825. Here is show version of device.Do i need to installed any specific IOS in Cisco 3825 device ? how to configure cisco 3825 as terminal server.
View 1 Replies View RelatedI am running ASA 5505 release 8.2(4) using a clientless SSL vpn to connect my assessors to the server via RDP to a Terminal server. Everything was working fine until last week when we had a Internet outage. During the outage some of the assessors claimed to have accepted a Cisco add-on to get into the site. once the internet came backup they could not connect to the terminal servers - what would happen is they would click on the link - say OK to connect the clipboard and the screen would pause for a few seconds then right back to the select options page.
they can get to other servers (non-terminal servers) but not to the ones they need. I can recreate the issue by waiting a REALLY long time before replying to a prompt to install an cisco add-on. I have users that can connect and others than can not. Also this only seems to affect Internet Explorer 8 and 9 does not affect Firefox
I have just purchased 2901 with HWIC-16A and 2 CAB-HD8-ASYNC Terminal Server to manage 16 (connect via console) cisco deivces.
Plese find attached the config file. I could not find proper docs on setting up this device as a terminal server. I have followed the following link but did not work.
[URL]
There are 16 Async (0/0/0 - 15) interfaces and also the following lines.
line 2line 0/0/0 0/0/1line 0/0/2 0/0/15
How can I connect to other Cisco devices via the terminal router?
usage of above 16 Async interfaces and lines.
I've heard that you can configure an 1811 router as a terminal server for remote console work.I have several of them in the lab and would love to try it out.
View 2 Replies View RelatedI have rolled out Terminal Services on Server 2008 R2 for a company I used to work for, it worked perfect the users could go home and browse to our web domain and login and use apps straight from the server.there'd be no Microsoft stuff to be accessed just pure Linux Servers but probarbly if users access the online terminal services on Linux they'd be using a Windows PC
View 1 Replies View RelatedIm having some printing issues whenever im working on the terminal server. If I try to print a document out in "landscape", it will print out "portrait", seen though it displays properly in landscape in the print preview. If Im working locally on my PC, it prints out fine.
View 2 Replies View RelatedPC-1 connect to printer as local printer but shared for other PC.
PC-2 through TS can see the shared printer. This is OK. But when the printer move and connect to PC-3.
PC-3 connect to the server through TS and want to have print out some document from the server to the printer. But unfortunately the Printer cannot be seen through TS. Even the printer already shared.
Using EMM as a nice friendly interface for their terminal server (ie router with NM-16A and octal cables)?when I ask the framework to run the following command it gets stuck will a blinking cursor and clear screen
<IOSExecCommand>"connect 10.1.1.1 2000"</IOSExecCommand>
however removing the port number allows it to connect fine.
<IOSExecCommand>"connect 10.1.1.1"</IOSExecCommand>
same symptom if iI were to replace connect with telnet
<IOSExecCommand>"telnet 10.1.1.1 2000"</IOSExecCommand>
even setting up an iphost does the same ie:
ip host R1 2000 10.1.1.1
<IOSExecCommand>"connect R1"</IOSExecCommand>
All of these commands work fine from the # prompt
i trying to set up a terminal server, 2811 with an HWIC-16A und two octo cables. [code] connect and sometimes not. It seems the connection is established but i don't get a prompt von the target device.The target devices are cisco 2811 and cisco catalysts 3560.
View 1 Replies View RelatedI've a RV082 with 2 internet connections.The idea is to permit external connections to my server and if one Internet line falls, automatically switch to the other.
We have configured the router in Smart Link backup.We try to connect with WAN1 and WAN2 enabled and all works fine.
We try to connect with WAN1 disabled and automatically WAN2 is activated.The problem start here...if WAN1 is activated while there are connections using WAN2, these connections falls!
How I must configure the router to permit that active connections are not disconnected from WAN2 even when WAN1 connection come back?
I have a Cisco 2901 Terminal server with AAA authentication via ACS server. I create twoaccounts on the acs server, cciesec2011 and vendor. Both accounts can log into the Cisco 2901 Terminal Server without any issues. By the way, I am NOT using AAA authorization on the Cisco Terminal Server. Once cciesec2011 or vendor accounts are authenticated, theseaccounts can access all the async line on the Cisco Terminal Server.
Now I have a new requirements. I would like to allow cciesec2011, once this account is successfully authenticated, this account has access to ALL async line on the Terminal Server. The "vendor" account, I want to restrict this account access only to async line 35 (there are 32 async lines available on the Cisco Terminal Server) and nothing else.
How can I accomplish without using AAA authorization on the Cisco Terminal Server?Is it possible to use "privlege level" to accomplish this? if so, how?
I am having two issues:
1. my email going out is working along with internal, but inbound email is not working. My barracuda email filter is 192.168.1.107 and my exchange 2007 is 192.168.1.222 along with this OWA does not work.
2. Terminal Services does not work when I try from the home pc in I get server not available or disconnected
Below is my congig
ASA Version 8.3(1)!hostname wsigatewaydomain-name wsystems.comenable password yVSkMxWRc/S396FB encryptedpasswd 2KFQnbNIdI.2KYOU encryptednames!interface Ethernet0/0 nameif outside security-level 0 ip address 64.XXX.XXX.XXX 255.XXX.XXX.XXXinterface Ethernet0/1 nameif inside security-level 100 ip address 192.168.1.1 255.255.0.0!interface Ethernet0/2 shutdown no nameif no security-level no ip address!interface Ethernet0/3 [Code]....
I have verizon wireless router to connect to the internet via FIOS. The public IP on the wireless router is DHCP assigned. I have my home lab with cisco 2511 and octal cables. I would like to be able to access the terminal server remotely via the internet when I'm not in. I'm concerned cause the wireless router is DHCP assigned IP. Even if I have a static IP on the ethernet port of the 2511 connected to the wireless router, I'm not sure if the NAT will work so it can be accessible from the internet.
View 2 Replies View RelatedI have a switch(6500) with 2 vlans(2 SUBNETS) and from the other side of my network i have 2 terminal servers.
I want to have a VIP in my 6500 switch which i have the 2 vlans and when the first vlan(network) try to connect to the VIP
my switch will forward to first terminal.When the second vlan try to connect to VIP the switch will forward to second terminal.
I'd like the switch to decide in wich terminal server will forwared the packet based on source network.
I am not sure how i can do this???I use VIP with SLB???I use NAT???PBR?
I have an annoying problem with networked printers disconnecting/disappearing when TS users logoff. Current configuration is: SQL server (WinSvr 2K8 R2 Std) has printers installed on it (standard TCP/IP Port) and printer is shared, there are also some printers installed on the DNS server and a couple of satellite offices. Users connect to TS servers (WinSvr 2K8 R2 & WinSvr 2K3) printers are connected and work fine until they logoff, when they log on the printers are gone "sometimes some printers are still there!?" I have tried logging onto the server as domain administrator and connecting printers but they won't even stay for administrator (have had this with win7 client machines) and tried directly 'console' at the server. I have looked at the printers on the SQL server and sharing properties, it is stoping printers from coming back at login on TS Note that local (client machines) connecting to the same shared printer from the SQL server don�t have the problem it's just on the TS server.
View 2 Replies View RelatedI have a set-up with multiple C2960 and C3750 switches. All these devices are being managed remotely. So basically I login to C2901, which is used as a Terminal Server, and reverse SSH to the console of each device. That's - I have assigned an IP to each port of the terminal server so that I can SSH directly to the desired device through via the mapped IP.
Now, recently I had to restart couple of switches - one C2960 and C3750. I initiated the reboot via console connection remotely. I could see the device logs for some time and then the logs stopped and there was no reaction from the console irrespective of any command I tried to enter.
I tried resetting the line on the terminal server, but that didn't work.
Now when I try to SSH the IP mapped to console of that particular device - i dont get any login prompt and there is no effect on device after giving any command. Although i can see the logs on the console session - but cant do anything.
I have a second way of connecting the device via inband- management, and checked the device config found it correct. It is same as other devices which are working correctly.
Both C3750 and C2960 are behaving exactly same - can see logs on console but see effect of even pressing enter - not getting login prompt as well.
trying to configure 2 cisco routers (3620 and 2501) Im using a RJ45 to DB9 cable and trying to see it in Tera Term. Nothing shows up in the terminal, and i cant even enter any imput. Ive tried hot-plugging into it, tried powering it up after making the connection, 3 different cables, 2 different computers (2 coms apiece-tried both) and every possible baud speed including the recommended 9600. (with no parity or flow control) the lights on the routers all come on and from what ive read they are not blinking out an error code. Ive also tried plugging the RJ45 into the AUX instead of CON and still, no cigar. BTW- running WinXP on Pentium4 2.53Ghz and 1G of RAM.
View 3 Replies View Relatedhow to configure log in Cisco 1841 router, terminal log
View 1 Replies View RelatedI have a ONT with a built in router but I need to install a separate router onto our network by connecting the router to the ONT. I need the extra router so that I could use some 3rd party hardware which can only be configured in D-link and Tp-link brand routers. I do not want to change the ONT system to the standard modem router system because the ONT also supports a system of internet phones. I'm curious if this is possible at all because a repair tech. told me that you could use the router as a transformer but so far it is not working. I'm really unfaimilar with the ONT configuration so I don't know if this plan can actually work . So far the router can not recieve a WAN connection and therefore can not obtain a Ip address.
View 2 Replies View Relatedi would like to know if its possible to connect a wireless router to GPON terminal
View 2 Replies View RelatedI have cisco 2911 router, this router not load putty and hyper terminal. my last command is confreg 0x3242 from rommon mode.
View 1 Replies View RelatedI have a server with 4 ethernet ports, 1G, they are bonded together, two of them was pluged into cat6500 module WS-X6724-TX. now we have moved the two ports to the replace module WS-X6748-GE-TX.
I have checked server side, the bond configuration are same no changed. what is possible reason replace module will cause link offline? why "sh run all" give the port is shutdown?
I have a VIP, which is listening on port 8312 in ACE LB and NO probes attached to it. In this scenario how does the ACE module perform the health monitoring ?
View 4 Replies View RelatedWe got a requirement for 2 number of X2-10GB-SR line card WS-X45-SUP6-E in WS-C4506-E.Customer want to connect with Fujitsu primary server . they have 10 gig module so i guess it will support with that.Also a doubt this X2-10GB-SR we can directly connect the firber sc multimode cable write no additional sfp required write .And for my knowledge if i use CVR-X2-SFP. I think to multimode sfp we have to insert write so do we get to 10 gig ports in one slot or how is it .
View 1 Replies View RelatedWhat are the maximum number of real servers, server farms and virtual servers i can configure on ACE30 module,Is there any documentation available on cisco site where i can check this? Does it depend on the hardware or does it depend on the software version?
View 3 Replies View RelatedRecently I have faced following problem in my office, We have purchased two new Dell Server Power Edge R910 with built-in 10GB FC Network card. Service tag of this two servers are given bellow.
1. 7D94C2S
2. 6D94C2S
You can can Check specification of this two server from dell website{ URL}
We have two CISCO switch and model is given bellow:
Brand: CISCO
Model: WS-C3560E-12SD
We want to connect server to switch through FC cable and both switch have SPF module. But when we connect server to switch, link do not establish even switch and server port light become off.
Then we have tested the following things:
1. Connect server to server through FC cable, it is okay.
2. Connect switch to switch through same FC cable, it is okay.
I don't understand why it is not working.