Cisco VPN :: 5505 - RDP To Terminal Server Failure
May 2, 2012
I am running ASA 5505 release 8.2(4) using a clientless SSL vpn to connect my assessors to the server via RDP to a Terminal server. Everything was working fine until last week when we had a Internet outage. During the outage some of the assessors claimed to have accepted a Cisco add-on to get into the site. once the internet came backup they could not connect to the terminal servers - what would happen is they would click on the link - say OK to connect the clipboard and the screen would pause for a few seconds then right back to the select options page.
they can get to other servers (non-terminal servers) but not to the ones they need. I can recreate the issue by waiting a REALLY long time before replying to a prompt to install an cisco add-on. I have users that can connect and others than can not. Also this only seems to affect Internet Explorer 8 and 9 does not affect Firefox
View 1 Replies
ADVERTISEMENT
May 5, 2013
I have a Cisco ASA 5505. This has been previously configured. I am trying to give it a factory reset and I am being able to connect via Putty and Hyper-terminal but I cannot enter anything. I am able to go into ROMMAN mode by using the esc key.
View 6 Replies
View Related
Jun 2, 2012
What command sequence disconnects you from a TS session? My setup is as followsr1 > TS > 2009-2621XM 2010-3825-R1 2011-3825-R2I can connect from the TS to any of the devices. The issue is that I am telnet'd to r1 and from there telnet'd to the TS. So when I type "Crtl+Shft+6, x" I go directly back to r1 and not the TS. Furthermore if I resume the session on r1 the TS is still connected to whatever session I was in prior to disconnecting. I've experimented with the disconnect and escape characters but I'm at a loss what it is that changes this.
View 4 Replies
View Related
Jul 24, 2012
We have the 16-port (NM-16A) and 32-port (NM-32A) asynchronous (async) network modules which provides 16 or 32 EIA/TIA-232 (formerly know as RS-232) data terminal equipment (DTE) serial interfaces at speeds up to 134.4 kbps . Few of the interfaces are connected to the console of cisco switches and routers , now we need to know that the remaining interfaces can be connected to console ports of devices other then cisco Systems to manage them , Will it work with them ?
View 0 Replies
View Related
May 18, 2011
Since Cisco 2511 is out of sale now and Cisco 1900 series are recommended to replace for the purpose of terminal/comm server. How to configure terminal server on HWIC-8A module?
View 3 Replies
View Related
Apr 19, 2012
I want to build up cisco 3800 series router as terminal server , i have Asycs 32A module in cisco 3825. Here is show version of device.Do i need to installed any specific IOS in Cisco 3825 device ? how to configure cisco 3825 as terminal server.
View 1 Replies
View Related
May 12, 2012
I have just purchased 2901 with HWIC-16A and 2 CAB-HD8-ASYNC Terminal Server to manage 16 (connect via console) cisco deivces.
Plese find attached the config file. I could not find proper docs on setting up this device as a terminal server. I have followed the following link but did not work.
[URL]
There are 16 Async (0/0/0 - 15) interfaces and also the following lines.
line 2line 0/0/0 0/0/1line 0/0/2 0/0/15
How can I connect to other Cisco devices via the terminal router?
usage of above 16 Async interfaces and lines.
View 4 Replies
View Related
May 15, 2012
I've heard that you can configure an 1811 router as a terminal server for remote console work.I have several of them in the lab and would love to try it out.
View 2 Replies
View Related
May 26, 2011
I have rolled out Terminal Services on Server 2008 R2 for a company I used to work for, it worked perfect the users could go home and browse to our web domain and login and use apps straight from the server.there'd be no Microsoft stuff to be accessed just pure Linux Servers but probarbly if users access the online terminal services on Linux they'd be using a Windows PC
View 1 Replies
View Related
May 11, 2011
Im having some printing issues whenever im working on the terminal server. If I try to print a document out in "landscape", it will print out "portrait", seen though it displays properly in landscape in the print preview. If Im working locally on my PC, it prints out fine.
View 2 Replies
View Related
Jan 28, 2011
PC-1 connect to printer as local printer but shared for other PC.
PC-2 through TS can see the shared printer. This is OK. But when the printer move and connect to PC-3.
PC-3 connect to the server through TS and want to have print out some document from the server to the printer. But unfortunately the Printer cannot be seen through TS. Even the printer already shared.
View 3 Replies
View Related
Jul 11, 2011
I have a cisco 2600 router with 4A/S module, can it become the terminal server? If yes, which kind of octal cable should I choose to connect to other cisco routers console ports?
View 0 Replies
View Related
Mar 25, 2012
Using EMM as a nice friendly interface for their terminal server (ie router with NM-16A and octal cables)?when I ask the framework to run the following command it gets stuck will a blinking cursor and clear screen
<IOSExecCommand>"connect 10.1.1.1 2000"</IOSExecCommand>
however removing the port number allows it to connect fine.
<IOSExecCommand>"connect 10.1.1.1"</IOSExecCommand>
same symptom if iI were to replace connect with telnet
<IOSExecCommand>"telnet 10.1.1.1 2000"</IOSExecCommand>
even setting up an iphost does the same ie:
ip host R1 2000 10.1.1.1
<IOSExecCommand>"connect R1"</IOSExecCommand>
All of these commands work fine from the # prompt
View 3 Replies
View Related
Nov 30, 2011
i trying to set up a terminal server, 2811 with an HWIC-16A und two octo cables. [code] connect and sometimes not. It seems the connection is established but i don't get a prompt von the target device.The target devices are cisco 2811 and cisco catalysts 3560.
View 1 Replies
View Related
Jan 31, 2012
I've a RV082 with 2 internet connections.The idea is to permit external connections to my server and if one Internet line falls, automatically switch to the other.
We have configured the router in Smart Link backup.We try to connect with WAN1 and WAN2 enabled and all works fine.
We try to connect with WAN1 disabled and automatically WAN2 is activated.The problem start here...if WAN1 is activated while there are connections using WAN2, these connections falls!
How I must configure the router to permit that active connections are not disconnected from WAN2 even when WAN1 connection come back?
View 1 Replies
View Related
Apr 19, 2011
I have a Cisco 2901 Terminal server with AAA authentication via ACS server. I create twoaccounts on the acs server, cciesec2011 and vendor. Both accounts can log into the Cisco 2901 Terminal Server without any issues. By the way, I am NOT using AAA authorization on the Cisco Terminal Server. Once cciesec2011 or vendor accounts are authenticated, theseaccounts can access all the async line on the Cisco Terminal Server.
Now I have a new requirements. I would like to allow cciesec2011, once this account is successfully authenticated, this account has access to ALL async line on the Terminal Server. The "vendor" account, I want to restrict this account access only to async line 35 (there are 32 async lines available on the Cisco Terminal Server) and nothing else.
How can I accomplish without using AAA authorization on the Cisco Terminal Server?Is it possible to use "privlege level" to accomplish this? if so, how?
View 5 Replies
View Related
Mar 5, 2011
I am having two issues:
1. my email going out is working along with internal, but inbound email is not working. My barracuda email filter is 192.168.1.107 and my exchange 2007 is 192.168.1.222 along with this OWA does not work.
2. Terminal Services does not work when I try from the home pc in I get server not available or disconnected
Below is my congig
ASA Version 8.3(1)!hostname wsigatewaydomain-name wsystems.comenable password yVSkMxWRc/S396FB encryptedpasswd 2KFQnbNIdI.2KYOU encryptednames!interface Ethernet0/0 nameif outside security-level 0 ip address 64.XXX.XXX.XXX 255.XXX.XXX.XXXinterface Ethernet0/1 nameif inside security-level 100 ip address 192.168.1.1 255.255.0.0!interface Ethernet0/2 shutdown no nameif no security-level no ip address!interface Ethernet0/3 [Code]....
View 2 Replies
View Related
Feb 1, 2011
Any example of router config for a terminal server.In fact I need a configuration for a router with multiple, low speed, asynchronous ports that are connected to other serial devices, for example,modems or console ports on routers or switches.With this router I would like to use a reverse telnet to connect with my devices using the serial connection.I find many examples on the Cisco web site but none with my router hardware configuration.My router is a 3620 router with a 8 port async (NM-8A/S) network module and I would like to use the 8 serial interfaces, each of them connecting a serial device.
Here is the show run and show ver :Router#show ver Cisco Internet work Operating System Software IOS (tm) 3600 Software (C3620-I-M), Version 12.3(25), RELEASE SOFTWARE (fc1)Copyright (c) 1986-2008 by Cisco Systems, Inc.Compiled Mon 28-Jan-08 20:16 by alnguyen
ROM: System Bootstrap, Version 11.1(19)AA, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1) Router up time is 1 minute System returned to ROM by reload System image file is "flash:c3620-i-mz.123-25.bin"
[Code]...
View 1 Replies
View Related
Sep 21, 2011
I have verizon wireless router to connect to the internet via FIOS. The public IP on the wireless router is DHCP assigned. I have my home lab with cisco 2511 and octal cables. I would like to be able to access the terminal server remotely via the internet when I'm not in. I'm concerned cause the wireless router is DHCP assigned IP. Even if I have a static IP on the ethernet port of the 2511 connected to the wireless router, I'm not sure if the NAT will work so it can be accessible from the internet.
View 2 Replies
View Related
Apr 22, 2012
I have a switch(6500) with 2 vlans(2 SUBNETS) and from the other side of my network i have 2 terminal servers.
I want to have a VIP in my 6500 switch which i have the 2 vlans and when the first vlan(network) try to connect to the VIP
my switch will forward to first terminal.When the second vlan try to connect to VIP the switch will forward to second terminal.
I'd like the switch to decide in wich terminal server will forwared the packet based on source network.
I am not sure how i can do this???I use VIP with SLB???I use NAT???PBR?
View 4 Replies
View Related
Jul 23, 2012
I have a 2611XM that I am using as a terminal server for my lab setup. Async is using octal cables. It works great with routers of all different models, but when I connect a switch of any model, it does not work. The connectivity LEDs don't even light (they do for the routers). The switches in question are 3750s and 3560s.
I have tried straight through from the octal cable to the console port of the switch, as well as a rollover with a converter, no luck. This does seem to be independent of configuration on the console port - even before the console port of the routers were properly configured, I at least had indication of physical connectivity.
View 2 Replies
View Related
Feb 8, 2012
I have an annoying problem with networked printers disconnecting/disappearing when TS users logoff. Current configuration is: SQL server (WinSvr 2K8 R2 Std) has printers installed on it (standard TCP/IP Port) and printer is shared, there are also some printers installed on the DNS server and a couple of satellite offices. Users connect to TS servers (WinSvr 2K8 R2 & WinSvr 2K3) printers are connected and work fine until they logoff, when they log on the printers are gone "sometimes some printers are still there!?" I have tried logging onto the server as domain administrator and connecting printers but they won't even stay for administrator (have had this with win7 client machines) and tried directly 'console' at the server. I have looked at the printers on the SQL server and sharing properties, it is stoping printers from coming back at login on TS Note that local (client machines) connecting to the same shared printer from the SQL server don�t have the problem it's just on the TS server.
View 2 Replies
View Related
Oct 23, 2012
I have a set-up with multiple C2960 and C3750 switches. All these devices are being managed remotely. So basically I login to C2901, which is used as a Terminal Server, and reverse SSH to the console of each device. That's - I have assigned an IP to each port of the terminal server so that I can SSH directly to the desired device through via the mapped IP.
Now, recently I had to restart couple of switches - one C2960 and C3750. I initiated the reboot via console connection remotely. I could see the device logs for some time and then the logs stopped and there was no reaction from the console irrespective of any command I tried to enter.
I tried resetting the line on the terminal server, but that didn't work.
Now when I try to SSH the IP mapped to console of that particular device - i dont get any login prompt and there is no effect on device after giving any command. Although i can see the logs on the console session - but cant do anything.
I have a second way of connecting the device via inband- management, and checked the device config found it correct. It is same as other devices which are working correctly.
Both C3750 and C2960 are behaving exactly same - can see logs on console but see effect of even pressing enter - not getting login prompt as well.
View 4 Replies
View Related
Mar 18, 2013
I bougth a used ASA 5505 on ebay which is experiencing this problem [url]... LEVELS or at least the described problem, if i touch the appliance while it is running it will somtimes go to this non working state as well
View 11 Replies
View Related
Dec 15, 2012
Firmware asa805-k8 was installed and saved on an ASA5505. Upon power failure the ASA5505 reverts to an older firmware, asa724-k8. 1) Is it normal for ASA5505's to revert to older version upon power failure. 2) ASDM/web browser doesn't work using IE--username and password brings to empty screen. how to revert back to later image.
"
# sh ver
Cisco Adaptive Security Appliance Software Version 7.2(4)
Device Manager Version 5.2(4)
[Code]......
View 3 Replies
View Related
Dec 5, 2012
I am having trouble accessing shares via client SSL VPN. I have an ASA 5505 running 8.4(4)1 The share is on on Ubuntu server 11.04 running Samba 3.5.8
This may not be strictly a Cisco issue and it seems to be an interoperbility issue between ASA and Samba. Or simply the smb.conf configuration.
I suspect the issue is down to the interpretation of Lanman on the ASA as I know the usernames and passwords work correctly when accesing the shares from other platforms (Windows Vista and Ubuntu desktop 12.04)
When monitoring the Samba logs I get the following errors: (amongst others)
ntlm_password_check: NT MD4 password check failed for user testuser
Storing account testuser with RID 1000
check_ntlm_password: sam authentication for user [testuser] FAILED with error
[Code].....
View 1 Replies
View Related
Apr 28, 2011
Connection denied due to NAT reverse path failure
View 2 Replies
View Related
Jul 30, 2012
When attempting to log in to a computer (running Windows 7 Professional) here at the office using the network administrator account, I get the error message: "The trust relationship between this workstation and the primary domain failed." I wasn't here when this laptop was set up, and so I don't know if any local user accounts were made or what their passwords would be if they were there, so I can't think of any way to log in to the machine and disconnect/reconnect to the domain which is really my only idea on how to fix it. Finding out what would cause this to suddenly start happening would also be nice, but mostly I just need to figure out how to get reconnected so I can get this back up and running.
View 1 Replies
View Related
Mar 28, 2011
I have a WD USB with approx 70,000 songs on it. When I try and scan the Music, it gets approx halfway though the songs, then the Media Servers stops all communications.
The only way I can get the Media Server to recover is to power cycle the E4200
View 9 Replies
View Related
Apr 24, 2013
Region : Argentina
Model : TL-WR740N
Hardware Version : V4
Firmware Version :
ISP :
Region : UnitedKingdom
Model : TL-WR740N
Hardware Version :
Firmware Version :
ISP :
I've configured the router using the Easy Setup Assistant CD provided and have a wifi connection between the router provided however when using network diagnostics, while the wifi connection is fine, I am getting "failed to connect to Internet" and "failed to connect to server" messages. I have tried adjusting settings manually but without any progress.
View 8 Replies
View Related
Aug 23, 2011
We have Cisco ASA 5505 with ASDM 5.2 We have one Proxy server in our Local Lab and pointed to Hosted service(Simple Signal)issue is, When our proxy server send register to hosted server, ASA change private IP and post with outside IP and src port as 1063 every time.
Here is debug log on real time monitoring.
Aug 24 2011 05:21:19 302015 203.xxx.xxx.226 192.168.1.51 Built outbound UDP connection 3774 for outside:203.xxx.xxx.226/5060 (203.xxx.xxx.226/5060) to inside:192.168.1.51/27014 (99.119.161.107/1142)
Aug 24 2011 05:21:19 607001 203.xxx.xxx.226 Pre- allocate SIP Via UDP secondary channel for inside:192.168.1.51/27014 to outside:203.xxx.xxx.226 from REGISTER message
Aug 24 2011 05:21:19 710005 203.xxx.xxx.226 99.xxx.xxx.107 UDP request discarded from 203.xxx.xxx.226/5060 to outside:99.xxx.xxx.107/1063
Here 99.xxx.xxx.107 is Our ASA Outside IP address 203.xxx.xxx.226 is Hosted server IP address. My ASA config is attached.
View 2 Replies
View Related
Sep 28, 2012
I know know nothing about cisco devices. Just wanted to get that out there. I recently came to a job that has a 5505 setup as the network gateway, and as a vpn for employees to work from home via the Cisco VPN remote client program. We had one main server that was domain controller, dns, and dhcp. It was a old 03 box, and I setup a new 08 r2 box on a different IP, and migrated all the above functions to it. Old server was a xxx.xxx.xxx.31, new server xxx.xxx.xxx.6. I found the java ASDM program(6.1) and connected to the ASA, and I have changed .31 to .6 in as many places as I can find, however, vpn clients on the outside can no longer connect to their desktops, as when i open a command prompt on their computer, the only IP they can ping is xxx.xxx.xxx.31, pinging xxx.xxx.xxx.6, or any other address fails. I'm guessing maybe it's in the firewall of the asa, but have no ideal really. Was there anything else I was suppose to do? Someplace I overlooked?
View 7 Replies
View Related
Mar 17, 2013
ASA 5505 Sec plus lic w/OS 9.1
I want to setup a quick and simple VPN server on my ASA. I want to do local authentication and, once authenticated, I want to allow all internal access. I only have 1 WAN IP. I'm finding a ton of conflicting info online. The ASA is already setup and is operational. I just need the correct commands to setup the VPN.
View 6 Replies
View Related
