Cisco WAN :: RV082 Dual Wan Terminal Server Configuration
Jan 31, 2012
I've a RV082 with 2 internet connections.The idea is to permit external connections to my server and if one Internet line falls, automatically switch to the other.
We have configured the router in Smart Link backup.We try to connect with WAN1 and WAN2 enabled and all works fine.
We try to connect with WAN1 disabled and automatically WAN2 is activated.The problem start here...if WAN1 is activated while there are connections using WAN2, these connections falls!
How I must configure the router to permit that active connections are not disconnected from WAN2 even when WAN1 connection come back?
View 1 Replies
ADVERTISEMENT
May 18, 2011
Since Cisco 2511 is out of sale now and Cisco 1900 series are recommended to replace for the purpose of terminal/comm server. How to configure terminal server on HWIC-8A module?
View 3 Replies
View Related
May 12, 2012
I have just purchased 2901 with HWIC-16A and 2 CAB-HD8-ASYNC Terminal Server to manage 16 (connect via console) cisco deivces.
Plese find attached the config file. I could not find proper docs on setting up this device as a terminal server. I have followed the following link but did not work.
[URL]
There are 16 Async (0/0/0 - 15) interfaces and also the following lines.
line 2line 0/0/0 0/0/1line 0/0/2 0/0/15
How can I connect to other Cisco devices via the terminal router?
usage of above 16 Async interfaces and lines.
View 4 Replies
View Related
Jun 12, 2012
RV082 configured for Dual WAN [Code]....
(2) identical DSL connections, configured as Static IP (not PPPoE) with modems in bridged mode. Static IP's are /25 subnet and same gateway ** this may be a problem? Dual WAN set for Load Balance, network service detection is OFF
We have a 2003 terminal server running and successfully receiving connections through both WAN connections. Depending on location, half the users are connecting to WAN1 IP and the other half to WAN2 IP. We are getting sporadic disconnects of the remote users when they are idle for a couple minutes and automatic reconnection of the session takes over a minute. If they close the (locked up) session and reconnect manually it will let them in right away.
Could the handling of the Dual-WAN be the culprit? Could the same gateway for both WAN's create this issue upstream (out of my control)?I am going to move everyone to connecting through WAN1 and then change to Smart Link Backup and see if the issues persist.
Another thought is to use a secondary IP on the terminal server and use Protocol Binding to match "All traffic" for IP1 to WAN1 and IP2 to WAN2, which theoretically would stabilize the situation?
View 36 Replies
View Related
Nov 30, 2011
i trying to set up a terminal server, 2811 with an HWIC-16A und two octo cables. [code] connect and sometimes not. It seems the connection is established but i don't get a prompt von the target device.The target devices are cisco 2811 and cisco catalysts 3560.
View 1 Replies
View Related
Feb 1, 2011
Any example of router config for a terminal server.In fact I need a configuration for a router with multiple, low speed, asynchronous ports that are connected to other serial devices, for example,modems or console ports on routers or switches.With this router I would like to use a reverse telnet to connect with my devices using the serial connection.I find many examples on the Cisco web site but none with my router hardware configuration.My router is a 3620 router with a 8 port async (NM-8A/S) network module and I would like to use the 8 serial interfaces, each of them connecting a serial device.
Here is the show run and show ver :Router#show ver Cisco Internet work Operating System Software IOS (tm) 3600 Software (C3620-I-M), Version 12.3(25), RELEASE SOFTWARE (fc1)Copyright (c) 1986-2008 by Cisco Systems, Inc.Compiled Mon 28-Jan-08 20:16 by alnguyen
ROM: System Bootstrap, Version 11.1(19)AA, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1) Router up time is 1 minute System returned to ROM by reload System image file is "flash:c3620-i-mz.123-25.bin"
[Code]...
View 1 Replies
View Related
Feb 21, 2013
I run 2 RV042 V1 for home and office with Gateway to Gateway VPN connection with single WAN connection in use. Everything works like a charm!
I was even able to create VPN connection with 2 WAN connection on one Router and 1 WAN connection on another with Smart link failover and VPN Tunel Backup.
I got problem though when i tried more complex connection diagram. [URL]
So basically I now have 2 ISP connections on each point with Static IPs and I'd like VPN Connection to be alive for ALL 4 options automatically with failovers (smart links) And tunel backups but i'm not sure if that's ever possible with my equipment.
View 2 Replies
View Related
Jun 2, 2012
What command sequence disconnects you from a TS session? My setup is as followsr1 > TS > 2009-2621XM 2010-3825-R1 2011-3825-R2I can connect from the TS to any of the devices. The issue is that I am telnet'd to r1 and from there telnet'd to the TS. So when I type "Crtl+Shft+6, x" I go directly back to r1 and not the TS. Furthermore if I resume the session on r1 the TS is still connected to whatever session I was in prior to disconnecting. I've experimented with the disconnect and escape characters but I'm at a loss what it is that changes this.
View 4 Replies
View Related
Jul 24, 2012
We have the 16-port (NM-16A) and 32-port (NM-32A) asynchronous (async) network modules which provides 16 or 32 EIA/TIA-232 (formerly know as RS-232) data terminal equipment (DTE) serial interfaces at speeds up to 134.4 kbps . Few of the interfaces are connected to the console of cisco switches and routers , now we need to know that the remaining interfaces can be connected to console ports of devices other then cisco Systems to manage them , Will it work with them ?
View 0 Replies
View Related
Apr 19, 2012
I want to build up cisco 3800 series router as terminal server , i have Asycs 32A module in cisco 3825. Here is show version of device.Do i need to installed any specific IOS in Cisco 3825 device ? how to configure cisco 3825 as terminal server.
View 1 Replies
View Related
May 2, 2012
I am running ASA 5505 release 8.2(4) using a clientless SSL vpn to connect my assessors to the server via RDP to a Terminal server. Everything was working fine until last week when we had a Internet outage. During the outage some of the assessors claimed to have accepted a Cisco add-on to get into the site. once the internet came backup they could not connect to the terminal servers - what would happen is they would click on the link - say OK to connect the clipboard and the screen would pause for a few seconds then right back to the select options page.
they can get to other servers (non-terminal servers) but not to the ones they need. I can recreate the issue by waiting a REALLY long time before replying to a prompt to install an cisco add-on. I have users that can connect and others than can not. Also this only seems to affect Internet Explorer 8 and 9 does not affect Firefox
View 1 Replies
View Related
May 15, 2012
I've heard that you can configure an 1811 router as a terminal server for remote console work.I have several of them in the lab and would love to try it out.
View 2 Replies
View Related
Jul 23, 2012
I use a RV082 with dual Wan and I cannot configure two SMTP.
Without authentication; a SMTP is specific of the provider.
When WAN1 comes down, SMTP to be used is the SMTP corresponding to WAN2 and vice versa.
Implementation of authentication with the mail server wil be useful. Possibility of two mail servers with indication of the corresponding WAN is also useful.
View 1 Replies
View Related
Mar 5, 2012
We have a RV082 configured with two ISP Wan connections. We recently implemented a VOIP phone system (SIP) (192.168.1.50) that is being used in appliance mode on our network. We currently have two WAN connections Load Balanced. My goal is to configure all my VOIP traffic to go out through the 1st ISP and the rest of the data through ISP #2. is this possible to achieve using the RV082? We are using a Skype SIP Trunk connection.
View 1 Replies
View Related
May 26, 2011
I have rolled out Terminal Services on Server 2008 R2 for a company I used to work for, it worked perfect the users could go home and browse to our web domain and login and use apps straight from the server.there'd be no Microsoft stuff to be accessed just pure Linux Servers but probarbly if users access the online terminal services on Linux they'd be using a Windows PC
View 1 Replies
View Related
May 11, 2011
Im having some printing issues whenever im working on the terminal server. If I try to print a document out in "landscape", it will print out "portrait", seen though it displays properly in landscape in the print preview. If Im working locally on my PC, it prints out fine.
View 2 Replies
View Related
Jan 28, 2011
PC-1 connect to printer as local printer but shared for other PC.
PC-2 through TS can see the shared printer. This is OK. But when the printer move and connect to PC-3.
PC-3 connect to the server through TS and want to have print out some document from the server to the printer. But unfortunately the Printer cannot be seen through TS. Even the printer already shared.
View 3 Replies
View Related
May 15, 2009
I am trying to set up a dual WAN on my RV082 - I have Verizon DSL on WAN1 and I am trying to establish Time Warner Road Runner on WAN2 as a backup in case DSL goes out on WAN1.I cannot get the router to recognize both connections at the same time. I have power cycled everything, the router is only picking up one internet signal at a time.
View 3 Replies
View Related
Jul 11, 2011
I have a cisco 2600 router with 4A/S module, can it become the terminal server? If yes, which kind of octal cable should I choose to connect to other cisco routers console ports?
View 0 Replies
View Related
Mar 25, 2012
Using EMM as a nice friendly interface for their terminal server (ie router with NM-16A and octal cables)?when I ask the framework to run the following command it gets stuck will a blinking cursor and clear screen
<IOSExecCommand>"connect 10.1.1.1 2000"</IOSExecCommand>
however removing the port number allows it to connect fine.
<IOSExecCommand>"connect 10.1.1.1"</IOSExecCommand>
same symptom if iI were to replace connect with telnet
<IOSExecCommand>"telnet 10.1.1.1 2000"</IOSExecCommand>
even setting up an iphost does the same ie:
ip host R1 2000 10.1.1.1
<IOSExecCommand>"connect R1"</IOSExecCommand>
All of these commands work fine from the # prompt
View 3 Replies
View Related
Apr 19, 2011
I have a Cisco 2901 Terminal server with AAA authentication via ACS server. I create twoaccounts on the acs server, cciesec2011 and vendor. Both accounts can log into the Cisco 2901 Terminal Server without any issues. By the way, I am NOT using AAA authorization on the Cisco Terminal Server. Once cciesec2011 or vendor accounts are authenticated, theseaccounts can access all the async line on the Cisco Terminal Server.
Now I have a new requirements. I would like to allow cciesec2011, once this account is successfully authenticated, this account has access to ALL async line on the Terminal Server. The "vendor" account, I want to restrict this account access only to async line 35 (there are 32 async lines available on the Cisco Terminal Server) and nothing else.
How can I accomplish without using AAA authorization on the Cisco Terminal Server?Is it possible to use "privlege level" to accomplish this? if so, how?
View 5 Replies
View Related
Mar 5, 2011
I am having two issues:
1. my email going out is working along with internal, but inbound email is not working. My barracuda email filter is 192.168.1.107 and my exchange 2007 is 192.168.1.222 along with this OWA does not work.
2. Terminal Services does not work when I try from the home pc in I get server not available or disconnected
Below is my congig
ASA Version 8.3(1)!hostname wsigatewaydomain-name wsystems.comenable password yVSkMxWRc/S396FB encryptedpasswd 2KFQnbNIdI.2KYOU encryptednames!interface Ethernet0/0 nameif outside security-level 0 ip address 64.XXX.XXX.XXX 255.XXX.XXX.XXXinterface Ethernet0/1 nameif inside security-level 100 ip address 192.168.1.1 255.255.0.0!interface Ethernet0/2 shutdown no nameif no security-level no ip address!interface Ethernet0/3 [Code]....
View 2 Replies
View Related
Dec 22, 2011
I am having issue with a RV082 with firmware:
v4.1.0.02-tm (Sep 16 2011 18:40:48)
On setup 1 I have;Using 2 WAN, 1 from fiber 5mbps symetric fixed public IP and other is DSL private dynamic dhcp address 3mbps/900kbps
On setup 2 i have:Using 1 WAN, from fiber 5mbps symetric fixed public ip Both router have exact same firewall configuration, subnet and port forwarding and we have the seccont backup DSL coming in a few day for setup 2.on both setup, the RV082 is the main internet gateway/firewall for a set of server...
Setup 1 work perfectly and been online for 2 week (since install) without issue
Setup 2 worked for 2 day then had to reboot, then work for few days then need reboot, now it look like it need to be rebooted every day. the internet just stop working and a simple reboot does the trick... also, when that happen I can stil remote in server that have port forwarded in the router or connect to router management port, but internet on the server is down... I tried opendns and google dns on both WAN connection and still no luck.I have followed instruction on various support forum;
-more reliable dns server
-lower MTU
-failover vs load balance
-disabling SPI and DoS protection
at this point I'm about to swap both router to see if it not a defective hardware or disconnect DSL WAN on setup 1 to see if its more stable but the whole point of installing this router was for Internet redundancy which so far dosent work as expected.
View 2 Replies
View Related
Sep 21, 2011
I have verizon wireless router to connect to the internet via FIOS. The public IP on the wireless router is DHCP assigned. I have my home lab with cisco 2511 and octal cables. I would like to be able to access the terminal server remotely via the internet when I'm not in. I'm concerned cause the wireless router is DHCP assigned IP. Even if I have a static IP on the ethernet port of the 2511 connected to the wireless router, I'm not sure if the NAT will work so it can be accessible from the internet.
View 2 Replies
View Related
Apr 22, 2012
I have a switch(6500) with 2 vlans(2 SUBNETS) and from the other side of my network i have 2 terminal servers.
I want to have a VIP in my 6500 switch which i have the 2 vlans and when the first vlan(network) try to connect to the VIP
my switch will forward to first terminal.When the second vlan try to connect to VIP the switch will forward to second terminal.
I'd like the switch to decide in wich terminal server will forwared the packet based on source network.
I am not sure how i can do this???I use VIP with SLB???I use NAT???PBR?
View 4 Replies
View Related
Jul 23, 2012
I have a 2611XM that I am using as a terminal server for my lab setup. Async is using octal cables. It works great with routers of all different models, but when I connect a switch of any model, it does not work. The connectivity LEDs don't even light (they do for the routers). The switches in question are 3750s and 3560s.
I have tried straight through from the octal cable to the console port of the switch, as well as a rollover with a converter, no luck. This does seem to be independent of configuration on the console port - even before the console port of the routers were properly configured, I at least had indication of physical connectivity.
View 2 Replies
View Related
Feb 8, 2012
I have an annoying problem with networked printers disconnecting/disappearing when TS users logoff. Current configuration is: SQL server (WinSvr 2K8 R2 Std) has printers installed on it (standard TCP/IP Port) and printer is shared, there are also some printers installed on the DNS server and a couple of satellite offices. Users connect to TS servers (WinSvr 2K8 R2 & WinSvr 2K3) printers are connected and work fine until they logoff, when they log on the printers are gone "sometimes some printers are still there!?" I have tried logging onto the server as domain administrator and connecting printers but they won't even stay for administrator (have had this with win7 client machines) and tried directly 'console' at the server. I have looked at the printers on the SQL server and sharing properties, it is stoping printers from coming back at login on TS Note that local (client machines) connecting to the same shared printer from the SQL server don�t have the problem it's just on the TS server.
View 2 Replies
View Related
Oct 23, 2012
I have a set-up with multiple C2960 and C3750 switches. All these devices are being managed remotely. So basically I login to C2901, which is used as a Terminal Server, and reverse SSH to the console of each device. That's - I have assigned an IP to each port of the terminal server so that I can SSH directly to the desired device through via the mapped IP.
Now, recently I had to restart couple of switches - one C2960 and C3750. I initiated the reboot via console connection remotely. I could see the device logs for some time and then the logs stopped and there was no reaction from the console irrespective of any command I tried to enter.
I tried resetting the line on the terminal server, but that didn't work.
Now when I try to SSH the IP mapped to console of that particular device - i dont get any login prompt and there is no effect on device after giving any command. Although i can see the logs on the console session - but cant do anything.
I have a second way of connecting the device via inband- management, and checked the device config found it correct. It is same as other devices which are working correctly.
Both C3750 and C2960 are behaving exactly same - can see logs on console but see effect of even pressing enter - not getting login prompt as well.
View 4 Replies
View Related
Jul 13, 2012
I have an old RV082 that I suppose has failed. The red diag light on the front panel is lit and nothing works. I've already replaced the unit, so I don't really need to fix it. Here's my issue: the setup on the old unit was pretty complex with a number of port forwards and other non-default settings. I'd like to recreate those items on my new router, but they were never written down so I don't know what they were. I've tried to connect a computer to one of the LAN ports, but they're all dead. Is there any way to get at the configuration page?
View 2 Replies
View Related
Aug 12, 2012
I am setting up a SBS 2011 Essentials sever using a rv082 router. I have a decent understanding of how everything is suppose to work, but execution has been sloppy. My aim is to set up a central storage location, back up services, remote access and VPN. Yesterday I had set up dhcp and dns roles on the sever, configed port forwarding and firewall setting on the router, at that point I was just bouncing around everywhere trying to get stuff to work, clearly not the best way I know. Before I left I reinstalled sbs for a couple of reason, along with resetting the router to default.
View 1 Replies
View Related
Nov 20, 2011
I have recently replaced an RV082 router that had failed with a new RV082. The previous router was set up to forward port 443 ssl requests to a server in the network. Worked flawlessly for years and that is why I replaced it with same model. The new router is also set up to forward port 443 ssl requests to the new server. The issue is that the router responds with its own certificate and does not forward the request to the server.
View 5 Replies
View Related
Apr 11, 2012
I have an RV082 V2 with 2.0.2.01-tm and I am having trouble with getting my Sprint Airvana to connect properly to the mobile service. I've read on the Sprint forums indicate putting the Airvana in the DMZ generally allows the device to work properly; however, none have the RV series routers for tips on how to do this appropriately. This device used to work fine behind the RV082, but I reset it one day and it no longer works.
The Airvana is a femtocell/router device with a WAN port and 3 LAN ports. If I connect the Airvana directly to my cable modem, I get the appropriate connection and can then make calls through the device instead of through the Sprint connection; I live in a basement unit and get crappy signal without the device. This proves the device works and that my ISP is not blocking the ports. Sprint indicates the device uses UDP 53, 67, 68, 500 and 4500. Their support sucks and they insist I put the Airvana before my router. I absolutely do not want to use the Airvana as the router. There are almost no configuration options in the router interface and it needs to be rebooted somewhat regularly, which would drop internet access throughout the house for 10-15 minutes while it reboots and finally establishes an internet connection.
As soon as put the Airvana behind the RV082, I no longer get the appropriate connection. I can, however, plug my computer into one of the LAN ports on the Airvana and connect to the internet in general. I have the router assign a static IP to the Airvana, and tried forwarding the required UDP ports to the IP. This did not fix the problem.
I can certainly troubleshoot the port forwarding issues, but I would also like to look into putting the device into the DMZ, if possible. I've not worked much in this area, so I am unsure how to appropriately configure the router to allow this to happen. Is it possible to have the Airvana in the router DMZ without having a public IP for the device itself?
View 2 Replies
View Related
Feb 27, 2013
Currently, the backup config is not human readable...any way to convert this?
View 1 Replies
View Related
