I use a RV082 with dual Wan and I cannot configure two SMTP.
Without authentication; a SMTP is specific of the provider.
When WAN1 comes down, SMTP to be used is the SMTP corresponding to WAN2 and vice versa.
Implementation of authentication with the mail server wil be useful. Possibility of two mail servers with indication of the corresponding WAN is also useful.
I've got some problem with my Mail Server since I've migrated to an ASA5510.Actually the server is in a DMZ with a private Ip ( 10.x.x.2) and it is translated to a Public IP ( 194.x.x.65).I use these configuration :
static (DMZ,LAN) 194.x.x.65 10.x.x.2 netmask 255.255.255.255 static (DMZ,LAN) 194.x.x.66 10.x.x.3 netmask 255.255.255.255 static (DMZ,WAN) 194.x.x.65 10.x.x.2 netmask 255.255.255.255 static (DMZ,WAN) 194.x.x.66 10.x.x.3 netmask 255.255.255.255 static (LAN,DMZ) 192.168.0.0 192.168.0.0 netmask 255.255.248.0
Some Users received in there mailbox a system administer error message :
Object : Impossible to deliver : test Your message could not be deliver to one or more of its recipients: 421 SMTP connection went away!
When they try to re sent it some times later, message is sent without problem.
We have a RV082 configured with two ISP Wan connections. We recently implemented a VOIP phone system (SIP) (192.168.1.50) that is being used in appliance mode on our network. We currently have two WAN connections Load Balanced. My goal is to configure all my VOIP traffic to go out through the 1st ISP and the rest of the data through ISP #2. is this possible to achieve using the RV082? We are using a Skype SIP Trunk connection.
View 1 Replies View RelatedRV082 configured for Dual WAN [Code]....
(2) identical DSL connections, configured as Static IP (not PPPoE) with modems in bridged mode. Static IP's are /25 subnet and same gateway ** this may be a problem? Dual WAN set for Load Balance, network service detection is OFF
We have a 2003 terminal server running and successfully receiving connections through both WAN connections. Depending on location, half the users are connecting to WAN1 IP and the other half to WAN2 IP. We are getting sporadic disconnects of the remote users when they are idle for a couple minutes and automatic reconnection of the session takes over a minute. If they close the (locked up) session and reconnect manually it will let them in right away.
Could the handling of the Dual-WAN be the culprit? Could the same gateway for both WAN's create this issue upstream (out of my control)?I am going to move everyone to connecting through WAN1 and then change to Smart Link Backup and see if the issues persist.
Another thought is to use a secondary IP on the terminal server and use Protocol Binding to match "All traffic" for IP1 to WAN1 and IP2 to WAN2, which theoretically would stabilize the situation?
Only trying to have the mail server reachable via the secondary ISP link if the primary ISP link goes out. The public MX records with priority markings should make it so any outside hosts tries the first ISP address then the second ISP address if the first is unavailable. I would be using object tracking to control the default gateway in the ASA. I'm just a bit fuzzy on the NAT with a dual ISP config on single box.It shouldn't happen but... if traffic comes in on ISP2 while ISP1 is still up (and the current default gate) that traffic should return out the ISP2 interface (using the ISP2 address and avoiding asymmetric routing) since there already an existing connection present inside the ASA. Any server initiated traffic would still use the current default gateway defined via object tracking on the ASA.
View 1 Replies View RelatedI've a RV082 with 2 internet connections.The idea is to permit external connections to my server and if one Internet line falls, automatically switch to the other.
We have configured the router in Smart Link backup.We try to connect with WAN1 and WAN2 enabled and all works fine.
We try to connect with WAN1 disabled and automatically WAN2 is activated.The problem start here...if WAN1 is activated while there are connections using WAN2, these connections falls!
How I must configure the router to permit that active connections are not disconnected from WAN2 even when WAN1 connection come back?
I am trying to set up a dual WAN on my RV082 - I have Verizon DSL on WAN1 and I am trying to establish Time Warner Road Runner on WAN2 as a backup in case DSL goes out on WAN1.I cannot get the router to recognize both connections at the same time. I have power cycled everything, the router is only picking up one internet signal at a time.
View 3 Replies View RelatedI am having issue with a RV082 with firmware:
v4.1.0.02-tm (Sep 16 2011 18:40:48)
On setup 1 I have;Using 2 WAN, 1 from fiber 5mbps symetric fixed public IP and other is DSL private dynamic dhcp address 3mbps/900kbps
On setup 2 i have:Using 1 WAN, from fiber 5mbps symetric fixed public ip Both router have exact same firewall configuration, subnet and port forwarding and we have the seccont backup DSL coming in a few day for setup 2.on both setup, the RV082 is the main internet gateway/firewall for a set of server...
Setup 1 work perfectly and been online for 2 week (since install) without issue
Setup 2 worked for 2 day then had to reboot, then work for few days then need reboot, now it look like it need to be rebooted every day. the internet just stop working and a simple reboot does the trick... also, when that happen I can stil remote in server that have port forwarded in the router or connect to router management port, but internet on the server is down... I tried opendns and google dns on both WAN connection and still no luck.I have followed instruction on various support forum;
-more reliable dns server
-lower MTU
-failover vs load balance
-disabling SPI and DoS protection
at this point I'm about to swap both router to see if it not a defective hardware or disconnect DSL WAN on setup 1 to see if its more stable but the whole point of installing this router was for Internet redundancy which so far dosent work as expected.
I wanted to ask a question about the diagram I have included. We are bringing up 2 MPLS WAN connections and would like some specifics on the best design. We are using BGP to the providers. From there we have big questions. We can run BGP internal and are licensed to do so on the N5K's. The N5Ks are currently using HSRP for inside LAN clients as default gateway. We want to load balance and provide redundant routes using a dynamic approach. Should we use BGP internal utilizing the connections between the routers? Should we use HSRP on the routers? How best to get the routes to the N5K and should we be considering this?
View 5 Replies View RelatedI run 2 RV042 V1 for home and office with Gateway to Gateway VPN connection with single WAN connection in use. Everything works like a charm!
I was even able to create VPN connection with 2 WAN connection on one Router and 1 WAN connection on another with Smart link failover and VPN Tunel Backup.
I got problem though when i tried more complex connection diagram. [URL]
So basically I now have 2 ISP connections on each point with Static IPs and I'd like VPN Connection to be alive for ALL 4 options automatically with failovers (smart links) And tunel backups but i'm not sure if that's ever possible with my equipment.
I have an RV042 that I have configured to send alert logs to a comcast email address. Recently comcast changed their SMTP port from 25 to 465. I can't find where to change the port settings in the RV042 to send the router logs via port 465.
View 1 Replies View RelatedI sold a rv220w to a customer. I've configured it but it seems that the router doesn't allow anonymous smtp. I've configured outlook on a computer with authentification request and it's working fine.
There is a software on a computer that I'm unable to change the authentification and it's not working ( Not able to send message ) I've search in the router and I've disabled these rule : "Block Anonymous ICMP Messages".
I have in my work RV016 10/100 16-Port VPN Router, working Ok and connected with 3 ADSL internet lines.
1- The problem is that when any line disconnect from internet it supposed to log this disconnection in internet in system log but it does not
2- I can't understand the option of sending mail with the logs, does it send when i press the button EMAIL LOG NOW, or it supposed to send when any log is added? and how to configure it.
I have both WAN1 and WAN2 connected to an ISP but only WAN2 should be used for outgoing mails. How and where can I specify this in the configuration?
View 3 Replies View RelatedJust installed a RV042 with dual wan connections. Would like to make the WAN 2 (new cable modem as well) the primary connection over WAN1 (DSL), however whenever I switch from WAN1 to WAN2 in Smark Link set up, our email server will not send mail out, even though nothing is blocking the connection.
View 0 Replies View RelatedI'm having an issue where our RV042 router is blocking some of our customers from sending us e-mails.I noticed thatCISCO has produced a newer version of the RVO42 V3.0 and has firmware version 4.x. can you upgrade the Linksys RV042 Hardware V 1.2 to the 4.x firmware? I have found a few articles and forums online about otherpeople having the same issue with the RV042 v1 randomly blocking, e-mail but no one ever has a solution to correct the issue.Some people have recommend to roll back to factory default and reconfigure the router as the config may by corrupt.
View 4 Replies View RelatedWe're getting the following message in the logs when we ry to connect: encrypted Informational Exchange message is invalid because it is for incomplete ISAKMP SA
One of the router is a V2 and the other is a V4 if that makes any difference.
I replaced a similar router from a competing company with the AC900 N900 router. I open Live Mail (IMAP) and keep it open during the day. Since switching over, when I periodically look at email on Live Mail, I frequently get a "Windows Live Mail" message saying "Your server unexpectedly terminated the connection. Possible causes for this include server problems, network problems, or a long period of inactivity." I have never received this message from either one of the previous routers - LinkSys, Netgear.
View 7 Replies View RelatedWe have an RV082 setup with WAN to the internet and LAN IP of 192.168.188.1.If I add a static route like so:
network: 192.168.166.0
mask: 255.255.255.0
gateway: 192.168.188.2
hop count: 1
interface: LAN
The device with IP 192.168.188.2 will be connected directly to one of the LAN ports on the router.Will that work to route, trying to get to 192.168.166.0 to the IP of 192.168.188.2?It just seems odd because the packets would hit the router then go back out through the LAN port.
isco epc3925 in transparent bridge provided by isp with following wan details
ip=x.x.x.120 subnet=255.255.255.248 gw=x.x.x.121 and 2 dns server ip's
I can't get the one-to-one nat working. read in some forums that the rv082 can do the job.
I have a Meraki Firewall that sits behind my Cisco RV082. The Meraki is setup to run a VPN connection with my server but I am having problems passing the VPN traffic through properly.
I have 2 Uverse Internet Connections that the RV082 using load balancing so that they are shared. I have 10 static IP's.
I am trying to come in on one of my static IP addresses throught the Cisco RV082 to the Meraki and after doing a capture on the meraki it appears that it is starting to receive data to intiate the VPN connection but when it sends data back to the VPN client machine it never makes it.
I have reset my RV082 router (both wit the reset switch and the factory default wizard) and run the setup wizard but regardless I can't connect to shaw.ca which is my service provider. I notice that if I use http://192.168.1.1 the browsers (IE & FF) default to https://192.168.1.1 and then I am prompted for a certificate. I can enter if I ignore the request but after getting in I simply cannot connect to my ISP.
View 4 Replies View RelatedIs it possbile to NAT to other subnets with the RV082. It is on a 192.168.41.x and I have a phone system on a 192.168.20.x. After searching all over others are saying no.
View 4 Replies View RelatedI just set up a new Linksys/Cisco RV082 router with the intent to get VPN working from outside the building. I have gone through the setup and while everything looks good, I have not been able to connect yet. I have tried everything that I know how, and am now hoping to get the answer from some pros.
Here's my setup. We use Comcast Business class internet. The modem is plugged into WAN port 1 on the RV082. I'm using the router as a DHCP server, that is working fine. My local subnet is 192.168.0.0/220
Right now all I want is to be able to log in as a client using QuickVPN. I set up one user and a client to VPN tunnel using the router's config page. Here's the settings I have:
Tunnel Interface is setup on WAN1, checkbox is enabled.
Local Group Setup
Local Security Gatewaytpe: IP Only
Local Security Group Type: Subnet
[Code]....
It seems like something is blocking the connection, but seeing that I have tried this after disabling the firewall completely it doesn't make sense to me. I also went into the config page for the modem and set up the router as a DMZ. I have also tried connecting with the client built into Windows 7, but that doesn't work either, I just get "connection failed with error 619"
I have the port in QuickVPN set to auto, but have tried both 443 and 60443 with same results.
I ran a port scan at [URL] and it shows I have 3 ports open...80,443, and 1723
I have a VPN tunnel from one RV082 to another, first router has IP range of 192.168.1.0 and the second one has range of 18.18.18.0, the connection works fine, here is where the issue starts, I am at a PC in the 18.18.18.0 network and I ping an IP in the other one e.g. 192.168.1.50 and it pings fine, but when I try to RDP into it or do anything to it I get no response, is it a firewall issue? Is it a NAT issue? I am at a loss, now that IP i mentioned does have RDP enabled and working because it is being port fowarded in the 192.168.1.0 router and I can access it through the public IP.
Also a workstation with a static IP 192.168.1.18 I can ping it if im in the local network but if I am in the remote one I cannot at all.
we have an RV082 router that a few days ago started restarting itself after normal usage.The simpton is that when people come to office, starting using the Internet the RV082 resets. It stays online for 3 to 12 minutes and then it resets again.
clicking on Reset to Factory Default in the web interfaceafter the reset, I confirmed that it was reset to factory default I reset it again using the reset buttomre-configure the RV082 manually.I also tested with another identical rv082 (hw version and firmware version) and after doing a backup of the config of the original rv082 and restoring it in the new rv082, the same problem happends.
I have an RV082 10/100 8-Port VPN Router and have configured the NAT table to allow for remote users, however I've run into an issue. It seems like there is a limited number of entries that you can put in the table,10, and I need to configure about 5 more IPs. Any way to expand the NAT table, or alternatively recommend a different router. I would also be willing to add another router to the network, but I have little experience doing that.
View 3 Replies View RelatedAre the RV042 and RV082 routers SIP AWARE?I haven't had any luck finding documentation stating such.
View 2 Replies View RelatedJust purchased a RV082 and once I switched a bunch of users over to it I can no longer access the web admin section. I have tried using both IE and Firefox and have used multiple workstations. I get to the login screen but it doesn't get any further. I am running the latest firmware v4.0.4.2-tm. It works for a while then just stops. The only fix is to turn off the device and back on and then it starts working again.
I've seen this issue on other small business cisco devices and had to stop using this because of this issue and switch to a higher grade cisco product but was hoping that this particular issue would have been resolved now across cisco's products.
I just migrated our office network router to a RV082. While configuring it, I came across three problems:
(1) From our ISP we have four public IP addresses which I want to make use of for outbound traffic. With the previous router we used we could configure LAN IPs(ranges) to map to static public IPs. Does RV082 support this? I could not find an option for that at the web-interface. From what I understand the 1-1 NATing only goes both incoming and outgoign ways and actually is 1-1 and not the many-to-one I am looking for.
(2) How is it possible to configure incoming port forwards to use a specific WAN interface? Will it always be the primary WAN interface?
(3) Does the telnet access provide more configuration options? I could not log in to it with the same user credentials as with the web-interface.
Serial Number : NKS1532xxxxFirmware Version : v4.0.4.02-tm (Jul 4 2011 13:30:56)PID VID : RV082 V03Firmware MD5 Checksum : 1f84d8d0a2a8b99f9bfa4409e64547aaLANWorking Mode : Gateway
we have a RV082 and have the DMZ option enable for a range of IPs within the same subnet of WAN IP and this works great. I have another range of Public IPs from our ISP that is not in the same subnet of the WAN IP and do not see a way on the RV082 to include this 2nd bank of Public IPs in the DMZ. Our ISP internet feed plugs into the RV082 WAN port and we have a switch pulgged into the DMZ port of the RV082 that is used to connect the public devices in the current DMZ. Both banks of Public IPs from our ISP come over via the ISP internet feed plugged into the WAN Port. My question is, if I cannot configure a DMZ rule to allow this 2nd range of Public IPs to "travel" to the RV082 DMZ port.
View 0 Replies View RelatedI would like to set the subnet mask off the lan to 255.255.240.0 but the selection menu do not allow to do it.
View 8 Replies View RelatedI wanted to know if you can connect a Cable modem to a SA520W, then connect a RV082 to the SA520W?
View 5 Replies View Related