Cisco Routers :: Can Connect SA520W To RV082
Sep 25, 2012I wanted to know if you can connect a Cable modem to a SA520W, then connect a RV082 to the SA520W?
View 5 Replies
ADVERTISEMENT
Cisco Routers :: RV082 - Possible To Connect Servers Each Other In VPN
Sep 8, 2011I did install server system with mscs and Domain controller and Active directory.I want to connect this dc/ac server from other places such as korea / and japan.
I have a public IP But our country ISP Don't open 135/445 port for security. So I can't connect DC/AC server from other places.At this time i did read many article and find good way to handle it. Is it possible for other servers to connect DC/AC server by using the RV082 VPN service.
Cisco Routers :: RV082 Can't Connect To Public IP From LAN
Feb 27, 2012I've a problem with Cisco RV082. I want to connect to my public IP from local IP. But it seems it's been block by the firewall.I've added a firewall rules to allow ANY connection from LAN to outside world. But has no effect.
LAN IP : 192.168.1.5.Public IP (which is assigned to LAN IP 192.168.1.5 by One-to-One NAT) : 118.xxx.xxx.xxx
Cisco Routers :: Connect From A Linux Station To RV082
Oct 6, 2010I want to connect from a Linux station to RV082, is it possible? What software can I use and with what configuration?
View 2 Replies View RelatedCisco Routers :: Unable To Connect To Network Printer Through RV082
Oct 2, 2011I installed a RV082 at my remote branch and I successfully created a VPN tunnel to my ASA5510 at our core data center.
The PC's that I plug into any of the 8 ports are working fine. However, when I plug in a network printer, it does not work from the network, only from a PC that is also plugged into the RV082, basically locally, using TCPIP
From our data center, I can ping the printer, but the printer shows 'Off-Line'. I even tried to add a TCPIP port, in the printer setup, and it does not see it.
Cisco Routers :: Connect RV082 WAN2 / DMZ Port To Network?
Jan 17, 2013I want to use WAN2 in DMZ mode on my RV082 router. I want to connect this to a router which will go to another network.
So it will look like this:
LAN1 192.168.188.0
|
|
|
[Code].....
UPDATE: This does not work. In case anyone else tries this, it is not possible with this model of router. The RV082 has to either be in gateway or router mode. In gateway mode, it is doing NAT, and the DMZ will not route correctly to the other LAN. In router mode, the DMZ does route correctly to the other LAN, but the internet will not work because NAT is turned off. We had to add a second RV082 to the configuration to get this working. It cannot be done with 1 RV082.
Cisco Routers :: SA520W Does Not Get IP On Optional WAN
Feb 9, 2012We are using a SA520W as our primary router and have a fiber connection attached to the default WAN interface. We would like to improve our uptime using a secondary internet connection on the optional WAN interface.
We have bought a dovado tiny 4g router for this other connection. It acts as a dhcp server but the Cisco router does not get an IP from the dovado router. The router works as expected when connected to a normal computer. But somehow the cisco router doesnt get an IP.
I have also tried to set a static IP for the Cisco router but that didn't work either. The dovado router is setup do deliver ip in the range 192.168.0.2-254
Cisco Routers :: Setup And Connect Two RV082 Together With Crossover Cable Between WAN Ports?
Jul 6, 2011how to setup and connect two RV082 routers together with a crossover cable between their WAN ports.This is to connect two separate LANS together via an ethernet connection. For staging we are setting everything up with a crossover cable in our shop. Ultimately the crossover cable will be replaced by a microwave link between the two LANS several miles apart. There will be no internet connection.
View 5 Replies View RelatedCisco Routers :: SA520W IPSec With VPN Client
Dec 14, 2009I have a problem to configure a IPSEC VPN on the SA520W ( 1.0.39) with Cisco VPN Client (5.0.05.290). In the logs are following error:
ERROR: Could not find configuration for x.x.x.xERROR: Could not find configuration for x.x.x.xERROR: Could not find configuration for x.x.x.xERROR: Could not find configuration for x.x.x.x
Cisco Routers :: SA520W Bridging Between To Private Lans
Jun 28, 2012connecting to separate private lans:
A) 192.168.1.x
B) 192.168.0.x
A is behind a Watchguard XTM25 11.5.3
B is behind a CISCO SA520W
Both have static public facing IP's.
B only has a IP based PBX system attached to it over a SIP ALG. (originally it was hooked up to the watchguard but they didn't play nice, but works great with the Cisco. Problem is the Cisco don't have all the features of the Watchguard)
A has all my users workstations attached. The issue is that computers on A need to talk to server on B for a desktop application to work. Since they are on separate subnets, it isn't working. The app itself still doesn't work by port forward/sNats, etc.
A & B are right next to each other, so cabling between them is not an issue.
Currently, I have a cable between the watchguard and the Cisco. The watchguard end is configured with a static private ip on the subnet A (the cisco side), and plugged into the lan on the cisco side. I have a policies to let all traffic flow freeley, and from the logs on the Watchguard, all A subnet traffic is correctly going to the Cisco via said cable.
But, nothing is coming back from the Cisco. So my question is, how can I get the Cisco to play nice with the other subnet and send traffic back to the B subnet?
Cisco Routers :: Sa520w - Set The Port Number For Syslog?
Mar 19, 2011Is is possible to set the port number for syslog eg 192.168.75.50:20514 ? i presume the protocol would stay udp
View 3 Replies View RelatedCisco Routers :: SA520W - Can't Access SSLVPN Corporate Connection
Feb 27, 2013A new Windows 8 computer can't access the SSLVPN corporate connection.
When we try to access the SSLVPN website to download the launcher (you have to download the VPN launcher everytime for our configuration), you can log in and that's fine, and then you can click on the VPN Tunnel link, a popup shows up but it doesn't actually download the launcher. Solutions we've tried so far:
1) Reinstalling C++ Redistirbutable
2) Adding the site to trusted sites and allowing unsigned ActiveX controls
3) Removing all internet objects through internet options.
Is there anything else we can try?
Cisco Routers :: SA520W Response Time In Replacing A Defective Unit
Apr 17, 2013Our company just recently bought a CISCO SA520W Security Appliance from a distributor here in the Philippines. Unfortunately, after a month of use, the LAN ports on the appliance started losing power. We reported this to the distributor and they sent a CISCO engineers to check on the unit. The engineers found the unit to be defective and need to be replaced.
Three weeks after the distributor pulled-out the unit, I have followed-up the status with them. They told me that they got no definite ETA from CISCO for the replacement unit. I followed-up with them again after a week. This time, they told me that the device is already in transit and it is coming from CISCO USA but they still don't have an expected time of arrival to give me.Does it really take more than a month for CISCO to replace a brand new defective unit? The serial number of our appliance is DNI1610G0G7.
Cisco Routers :: RV016 Gateway To Gateway RV082 Won't Connect
Mar 9, 2012New hardware here, requesting a bit of your knowledge, We are tryingin to setup a simple gateway to gateway VPN
HomeA Has an RV016 with a public static IP
Local Group Security Gateway type is IP Only with the IP
Local Security Group Type is Subnet, with the local IP class 192.160.0.0
Remote Security Gateway Type: Dynamic + Email
Email address some@emailaddress.com
Remote Security Group Type: Subnet
IP Address 192.168.1.0
IPSec Setup as default with nice password.
HomeB has an RV082 with a dynamic ADSL link
Local Group Security Gateway type is DynamicIP +Email
Email address some@emailaddress.com
Local Security Group Type is Subnet, with the local IP class 192.160.1.0
Remote Security Gateway Type: IP Only
Remote Security Group Type: Subnet
IP Address 192.168.0.0
IPSec Setup as default with nice password.
The idea is for HomeB which has a dynamic IP, to reach HomeA, which has a static IP and connect. But they just wont. I have not clue what's wrong, I followed the instructions, maybe i miss interpreted something. I could share the VPN logs for both., Im getting a lot of errors there.
Cisco Routers :: VPN Between Two RV082 Routers Not Working?
Aug 7, 2012We're getting the following message in the logs when we ry to connect: encrypted Informational Exchange message is invalid because it is for incomplete ISAKMP SA
One of the router is a V2 and the other is a V4 if that makes any difference.
Cisco Routers :: LAN To LAN Routing RV082?
Jan 29, 2013We have an RV082 setup with WAN to the internet and LAN IP of 192.168.188.1.If I add a static route like so:
network: 192.168.166.0
mask: 255.255.255.0
gateway: 192.168.188.2
hop count: 1
interface: LAN
The device with IP 192.168.188.2 will be connected directly to one of the LAN ports on the router.Will that work to route, trying to get to 192.168.166.0 to the IP of 192.168.188.2?It just seems odd because the packets would hit the router then go back out through the LAN port.
Cisco Routers :: Rv082 Configure One-to-one Nat
Nov 17, 2011isco epc3925 in transparent bridge provided by isp with following wan details
ip=x.x.x.120 subnet=255.255.255.248 gw=x.x.x.121 and 2 dns server ip's
I can't get the one-to-one nat working. read in some forums that the rv082 can do the job.
Cisco Routers :: RV082 VPN Passthrough
May 9, 2013I have a Meraki Firewall that sits behind my Cisco RV082. The Meraki is setup to run a VPN connection with my server but I am having problems passing the VPN traffic through properly.
I have 2 Uverse Internet Connections that the RV082 using load balancing so that they are shared. I have 10 static IP's.
I am trying to come in on one of my static IP addresses throught the Cisco RV082 to the Meraki and after doing a capture on the meraki it appears that it is starting to receive data to intiate the VPN connection but when it sends data back to the VPN client machine it never makes it.
Cisco Routers :: RV082 / No Connection To ISP
Nov 12, 2012I have reset my RV082 router (both wit the reset switch and the factory default wizard) and run the setup wizard but regardless I can't connect to shaw.ca which is my service provider. I notice that if I use http://192.168.1.1 the browsers (IE & FF) default to https://192.168.1.1 and then I am prompted for a certificate. I can enter if I ignore the request but after getting in I simply cannot connect to my ISP.
View 4 Replies View RelatedCisco Routers :: RV082 NAT To Other Subnets?
Jan 12, 2012Is it possbile to NAT to other subnets with the RV082. It is on a 192.168.41.x and I have a phone system on a 192.168.20.x. After searching all over others are saying no.
View 4 Replies View RelatedCisco Routers :: VPN Fail With RV082
Jan 14, 2013I just set up a new Linksys/Cisco RV082 router with the intent to get VPN working from outside the building. I have gone through the setup and while everything looks good, I have not been able to connect yet. I have tried everything that I know how, and am now hoping to get the answer from some pros.
Here's my setup. We use Comcast Business class internet. The modem is plugged into WAN port 1 on the RV082. I'm using the router as a DHCP server, that is working fine. My local subnet is 192.168.0.0/220
Right now all I want is to be able to log in as a client using QuickVPN. I set up one user and a client to VPN tunnel using the router's config page. Here's the settings I have:
Tunnel Interface is setup on WAN1, checkbox is enabled.
Local Group Setup
Local Security Gatewaytpe: IP Only
Local Security Group Type: Subnet
[Code]....
It seems like something is blocking the connection, but seeing that I have tried this after disabling the firewall completely it doesn't make sense to me. I also went into the config page for the modem and set up the router as a DMZ. I have also tried connecting with the client built into Windows 7, but that doesn't work either, I just get "connection failed with error 619"
I have the port in QuickVPN set to auto, but have tried both 443 and 60443 with same results.
I ran a port scan at [URL] and it shows I have 3 ports open...80,443, and 1723
Cisco Routers :: VPN Not Working With RV082
Jan 24, 2012I have a VPN tunnel from one RV082 to another, first router has IP range of 192.168.1.0 and the second one has range of 18.18.18.0, the connection works fine, here is where the issue starts, I am at a PC in the 18.18.18.0 network and I ping an IP in the other one e.g. 192.168.1.50 and it pings fine, but when I try to RDP into it or do anything to it I get no response, is it a firewall issue? Is it a NAT issue? I am at a loss, now that IP i mentioned does have RDP enabled and working because it is being port fowarded in the 192.168.1.0 router and I can access it through the public IP.
Also a workstation with a static IP 192.168.1.18 I can ping it if im in the local network but if I am in the remote one I cannot at all.
Cisco Routers :: RV082 Restarts Itself
Jul 28, 2010we have an RV082 router that a few days ago started restarting itself after normal usage.The simpton is that when people come to office, starting using the Internet the RV082 resets. It stays online for 3 to 12 minutes and then it resets again.
clicking on Reset to Factory Default in the web interfaceafter the reset, I confirmed that it was reset to factory default I reset it again using the reset buttomre-configure the RV082 manually.I also tested with another identical rv082 (hw version and firmware version) and after doing a backup of the config of the original rv082 and restoring it in the new rv082, the same problem happends.
Cisco Routers :: RV082 NAT Table Too Small
Mar 15, 2013I have an RV082 10/100 8-Port VPN Router and have configured the NAT table to allow for remote users, however I've run into an issue. It seems like there is a limited number of entries that you can put in the table,10, and I need to configure about 5 more IPs. Any way to expand the NAT table, or alternatively recommend a different router. I would also be willing to add another router to the network, but I have little experience doing that.
View 3 Replies View RelatedCisco Routers :: Are RV042 And RV082 SIP Aware?
Jul 18, 2012Are the RV042 and RV082 routers SIP AWARE?I haven't had any luck finding documentation stating such.
View 2 Replies View RelatedCisco Routers :: RV082 Web Admin Lockup?
Oct 20, 2011Just purchased a RV082 and once I switched a bunch of users over to it I can no longer access the web admin section. I have tried using both IE and Firefox and have used multiple workstations. I get to the login screen but it doesn't get any further. I am running the latest firmware v4.0.4.2-tm. It works for a while then just stops. The only fix is to turn off the device and back on and then it starts working again.
I've seen this issue on other small business cisco devices and had to stop using this because of this issue and switch to a higher grade cisco product but was hoping that this particular issue would have been resolved now across cisco's products.
Cisco Routers :: Outbound Nating With RV082?
Jan 9, 2012I just migrated our office network router to a RV082. While configuring it, I came across three problems:
(1) From our ISP we have four public IP addresses which I want to make use of for outbound traffic. With the previous router we used we could configure LAN IPs(ranges) to map to static public IPs. Does RV082 support this? I could not find an option for that at the web-interface. From what I understand the 1-1 NATing only goes both incoming and outgoign ways and actually is 1-1 and not the many-to-one I am looking for.
(2) How is it possible to configure incoming port forwards to use a specific WAN interface? Will it always be the primary WAN interface?
(3) Does the telnet access provide more configuration options? I could not log in to it with the same user credentials as with the web-interface.
Serial Number : NKS1532xxxxFirmware Version : v4.0.4.02-tm (Jul 4 2011 13:30:56)PID VID : RV082 V03Firmware MD5 Checksum : 1f84d8d0a2a8b99f9bfa4409e64547aaLANWorking Mode : Gateway
Cisco Routers :: Rv082 Dmz Rule Limitations
Apr 27, 2013we have a RV082 and have the DMZ option enable for a range of IPs within the same subnet of WAN IP and this works great. I have another range of Public IPs from our ISP that is not in the same subnet of the WAN IP and do not see a way on the RV082 to include this 2nd bank of Public IPs in the DMZ. Our ISP internet feed plugs into the RV082 WAN port and we have a switch pulgged into the DMZ port of the RV082 that is used to connect the public devices in the current DMZ. Both banks of Public IPs from our ISP come over via the ISP internet feed plugged into the WAN Port. My question is, if I cannot configure a DMZ rule to allow this 2nd range of Public IPs to "travel" to the RV082 DMZ port.
View 0 Replies View RelatedCisco Routers :: RV082 LAN Subnet Mask
Nov 12, 2012I would like to set the subnet mask off the lan to 255.255.240.0 but the selection menu do not allow to do it.
View 8 Replies View RelatedCisco Routers :: RV082 VPN - Connects But No Access?
Mar 24, 2013We recently moved our network over to RV082 router and its working great, well now we want to take advantage of VPN for our sales staff.
I was able to setup the VPN and using a PC at a remote office I can launch the quick connect and it connects right away, RV0 even shows the user connected. However the user cannot ping anything on our network via name or IP, connect to any resources, etc...
My understanding was when the client VPN would connect the user would get an IP from DHCP (this is on our Server 2008 DC) and they would be using that address, but when I run IPCONFIG on the client PC they just have there standard IP from remote office.
Cisco Routers :: RV082 Backup Vpn To C2851?
Feb 10, 2013I'm planning to buy a few Cisco RV082's for remote offices and using them to connect to main office Cisco 2851 site to site vpn. So I guess, simple site to site vpn will work without much problem, but I wonder, will backup vpn feature work as expected on backup WAN channel and how should I configure it on the IOS side?
View 1 Replies View RelatedCisco Routers :: RV082 - Internal DNS Server
Jan 19, 2010The RV082 is a great unit, however when VPN clients connect the QuickVPN Client has a setting to use the Remote DNS settings of the RV082. The RV082 has no way of linking or using a user-defined DNS. I have an internal DNS Server that I would like the VPN Clients to query on internal name lookups (kindof the point of having client vpn, so they can access internal network shares etc. On the diagnostic page the ping and name resolution can only check external DNS and internal IP's. Wouldn't it make sense to at least make the RV082 aware of internal DNS Servers? Then the Ping and DNS lookup would be able to test both zones? Is this something that can be looked at by Linksys Developers for this product? The WRV210 (a cheaper and lower level model) has this functionality.
View 8 Replies View RelatedCisco Routers :: RV082 V3 Web Management Inaccessible
Aug 29, 2012Experiencing a strange issue with v3 hardware. After a short period of time, I cannot log into the web administration - either locally through standard port or remote through non-standard port get login prompt, enter correct username & password, page refreshes with blank background and first page (status?) never shows.power cycling the router restores access to the web administration page, for an uncertain period of time before it barfs again.
I was running older firmware, updated to newest 4.2.1.02 (?) and same problem. Only thing that is better is the internet didn't completely lock up when I tried to access the administration page, like it did on the older firmware.