Cisco Routers :: Unable To Connect To Network Printer Through RV082
Oct 2, 2011
I installed a RV082 at my remote branch and I successfully created a VPN tunnel to my ASA5510 at our core data center.
The PC's that I plug into any of the 8 ports are working fine. However, when I plug in a network printer, it does not work from the network, only from a PC that is also plugged into the RV082, basically locally, using TCPIP
From our data center, I can ping the printer, but the printer shows 'Off-Line'. I even tried to add a TCPIP port, in the printer setup, and it does not see it.
View 1 Replies
ADVERTISEMENT
Jan 17, 2013
I want to use WAN2 in DMZ mode on my RV082 router. I want to connect this to a router which will go to another network.
So it will look like this:
LAN1 192.168.188.0
|
|
|
[Code].....
UPDATE: This does not work. In case anyone else tries this, it is not possible with this model of router. The RV082 has to either be in gateway or router mode. In gateway mode, it is doing NAT, and the DMZ will not route correctly to the other LAN. In router mode, the DMZ does route correctly to the other LAN, but the internet will not work because NAT is turned off. We had to add a second RV082 to the configuration to get this working. It cannot be done with 1 RV082.
View 1 Replies
View Related
Jan 14, 2011
We have 2 computers the main one running OS XP and mine running Vista. Previously, we had no problems with my computer finding the main on the network along with the printer. But now the main computer can see mine (printer and PC) but I cannot connect to the main. Mine does not see the printer nor the PC. We are both running the same virus protection, which is Norton. I really want to use the main computer's printer, which I was able to do until for some reason now I go into networking and it is not there. I know it is marked as shared. When I go into setup network printer and type the name of the printer a window pops up "The printer sever spooling service is not available". I have uninstalled the printer software and drivers and reinstalled but still not showing up on the network?
When I click print a document the printer I am looking for is there but it shows as offline, which it is not. I am not 100% sure but seemed to occur when we switched from Mckfee to Norton?
View 14 Replies
View Related
May 15, 2011
I have recenly installed a RV082 with two ADSL modems connected to Broadband lines. Access to our networks is done via VPN accounts configured on Windows Vista laptops. The VPN network works fine and everyone has access to their network data and the Intranet/Internet.
I'm having problems with connecting a network printer to access over the VPN. We have managed to get a IBM1532 network printer working using the following network details by allowing the IP address of the printer through our VPN network/firewall.
We had to connect a Xerox C2424 workstation printer on site, so we configured the device using the same network details as the IBM printer, connected it to one of the available ports on one of the Broadband modems but we could not get the printer to be seen or connected to using this setup.
However I connect my own Home Laptop PC configured with the IP port settings above directly to the same modem as the Xerox printer this works but only after we changed the IP gateway address on the printer to match the modem.
If I switch on DHCP on the printer it finds the IP gateway address of the RV082 but will not allow us to send anything to it.As the ADSL lines are on a Dynamic IP rather than Static.
View 2 Replies
View Related
Mar 21, 2011
I have 2 desktops (running windows 7), a Canon MF8300 printer, and an outgoing ethernet line, all on a Netgear Advanced Cable Modem Gateway CGD24-CPR. I'm only concerned with having the 2 desktops set up with the Canon printer.Both computers have been connected to the printer before and I have the startup disk. But once the new offices were set up and both of the desktops were moved, I can no longer access or find the printer.
I can IPconfig the Desktops for their IPV4 addresses and both desktops recognize eachother on a Homegroup, but I can't find the printer. I printed off the print configuration page from the printer which gave me an IP address (printer is set for auto-obtain), but using an IP search won't bring up the printer.All of the devices are plugged into ethernet ports set up for the three different office they are in and the actual location of the Netgear cable modem/router is over 100 feet away. My primary concern is getting the printer for the desktops, but I also need to add a wireless router into one of those office in the future.
View 15 Replies
View Related
Jun 7, 2013
Router is a Model F9K1105. Two PCs, a MAC laptop and two TiVo DVRs have connected without any issues. Printer SEES the network but will not connect.
View 1 Replies
View Related
Sep 25, 2012
I wanted to know if you can connect a Cable modem to a SA520W, then connect a RV082 to the SA520W?
View 5 Replies
View Related
Sep 8, 2011
I did install server system with mscs and Domain controller and Active directory.I want to connect this dc/ac server from other places such as korea / and japan.
I have a public IP But our country ISP Don't open 135/445 port for security. So I can't connect DC/AC server from other places.At this time i did read many article and find good way to handle it. Is it possible for other servers to connect DC/AC server by using the RV082 VPN service.
View 1 Replies
View Related
Feb 27, 2012
I've a problem with Cisco RV082. I want to connect to my public IP from local IP. But it seems it's been block by the firewall.I've added a firewall rules to allow ANY connection from LAN to outside world. But has no effect.
LAN IP : 192.168.1.5.Public IP (which is assigned to LAN IP 192.168.1.5 by One-to-One NAT) : 118.xxx.xxx.xxx
View 6 Replies
View Related
Oct 6, 2010
I want to connect from a Linux station to RV082, is it possible? What software can I use and with what configuration?
View 2 Replies
View Related
Dec 30, 2011
I am able to make a connect to my remote RV082, I can ping the inside network gateway from the remote end but I cannot ping or get to any devices on the remote network, my local network is 192.168.15.x and the remote network is 192.168.0.x I am using WIN 7, and using the native VPN setup in WIN 7, I do a print route and everything looks fine there, I can't figure this out
View 8 Replies
View Related
Nov 4, 2012
I have the RV082 v03 i set it for load balancing i have 2 8gb Adsl modem connected to Wan1 and Wan2
Question how can i assign a certain pc to use the connection on Wan2, what i would like is to assign a specific pc on the network to wan2
View 2 Replies
View Related
Jul 6, 2011
how to setup and connect two RV082 routers together with a crossover cable between their WAN ports.This is to connect two separate LANS together via an ethernet connection. For staging we are setting everything up with a crossover cable in our shop. Ultimately the crossover cable will be replaced by a microwave link between the two LANS several miles apart. There will be no internet connection.
View 5 Replies
View Related
Nov 27, 2011
I am able to connect 3 computers to the network. When I enter the passkey in the HP printer, the network goes down and I need to restart it. Then computers are back on, but the printer cannot be seen. The printer driver is downloaded.
View 3 Replies
View Related
Aug 10, 2011
I have windows 7 on one client and windows xp on seconad client. the problem occure when i share hp 1320 pcl 5 printer on network..when i go to install the error shows " unable to find *.inf file".
View 4 Replies
View Related
Jan 2, 2012
i am having problem adding the officejet printer that was uninstalled because it was not working. after three days of online support from HP and Lynksys, I am about to buy a new printer. Can't add printer wirelessly or wired.
View 1 Replies
View Related
Jan 23, 2012
i am having real issues with my printer, i have a network of 3 computers and it was attached to a printer that worked fine, i then changed the printer for a new one and i am now unable to find this printer on my network. i have installed drivers on the computers. how do i find the printer. the network works fine with everything else.
View 4 Replies
View Related
Apr 19, 2012
Due to bandwith requirements, we need to join a network with a RV016 to a network with an RV082 via a point to point air bridge. (VPN over adls was not cutting it) fortunatelly there is line of sight.
The info
LocationA LocationB
RV016 RV082
WAN1 ADSL modem WAN1 ADSL Modem
WAN2 DedicatedIP modem WAN2 Free
WAN3..7 free
[code]....
We need LAN-B endpoints to be able to reach servers on location A and viceversa.
We pre configured two point to point radios for the tower people to install. (we could change this configs)
Topology (crude sketch)[URL]
Our questions: best port to plug the radios into the RVs WAN ports? switch ports? What rules or static routes need to be created?
View 2 Replies
View Related
Feb 20, 2013
Region : UnitedStates
Model : TL-WR841ND
Hardware Version : V5
Firmware Version :
ISP : charter cable
I am trying to install a HP officejet 6700 all-in-one wireless printer on my home network. I can see the MAC and static IP addresses in the ARP list but fail to connect to it via my laptop. I have disabled the Norton Internet Security smart firewall and the windows firewall and still fail to connect. I have spent 2 four hour chat sessions with HP and they tell me it is my router. They had me change the channel to 6 from 5 and 11g-only from the 11gb-mixed and it still does not connect. They also had me do a firmware upgrade but the Printer was up to date.
View 2 Replies
View Related
Mar 22, 2013
Region : Argentina
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : latest
ISP : telecentro
I recently purchased a tl-wr842nd, my printer is a hp laserjet 1020 and it is in the compatible list as I seen. The problem is that I connect the printer in the usb routers port and the led do not light up, I tried putting my pendrive to see if the usb routers port wasn't working but it does since the pendrive is accepted and online and the usb led lights.I downloaded and installed the latest firmware but there's no change, I did everything like it saids in the faq 415 where it explains how to install and use printer server with no luck.
View 1 Replies
View Related
Jan 24, 2011
I cannot connect to a PPTP on the outside of my network.We have a RV082, port 1723.It says verifying username and password but then disconnects.The error log says Blocked IP Spoofing.
View 1 Replies
View Related
Mar 2, 2012
I recently upgraded my d-link router DI-524 for Netgear N600 WNDR3700v3 and every component (wired or wireless) is working except network printer. I have it wired directly to the router and all pcs on the home network can see it, however when i select to do a test print, nothing prints to the printer and i get error. I had this setup using the d-link router with both the printer and the XP PC wired directly to the router and using the XP PC as a network pc sharing the printer to other pcs (Vista / Windows 7) on the home network.The printer is a Toshiba e-studio 160 series.. I re-added the print drivers for XP and still not able to print. Is there anything else I can try?
View 9 Replies
View Related
Mar 9, 2012
New hardware here, requesting a bit of your knowledge, We are tryingin to setup a simple gateway to gateway VPN
HomeA Has an RV016 with a public static IP
Local Group Security Gateway type is IP Only with the IP
Local Security Group Type is Subnet, with the local IP class 192.160.0.0
Remote Security Gateway Type: Dynamic + Email
Email address some@emailaddress.com
Remote Security Group Type: Subnet
IP Address 192.168.1.0
IPSec Setup as default with nice password.
HomeB has an RV082 with a dynamic ADSL link
Local Group Security Gateway type is DynamicIP +Email
Email address some@emailaddress.com
Local Security Group Type is Subnet, with the local IP class 192.160.1.0
Remote Security Gateway Type: IP Only
Remote Security Group Type: Subnet
IP Address 192.168.0.0
IPSec Setup as default with nice password.
The idea is for HomeB which has a dynamic IP, to reach HomeA, which has a static IP and connect. But they just wont. I have not clue what's wrong, I followed the instructions, maybe i miss interpreted something. I could share the VPN logs for both., Im getting a lot of errors there.
View 2 Replies
View Related
Feb 19, 2013
Region : India
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 3.12.11 Build 120320 Rel.51047n
ISP : BSNL
I am facing some issue in LAN network.I have connected one desktop( win 7) and another desktop (win xp) to the TP link router. Both the computers got ip address and able to share the internet. But both the computers are not in the same network. That is they cant PING each other. hence they are not visible to each other.
View 4 Replies
View Related
Oct 26, 2011
we're using a network and only one computer can't seem to connect to the printer. it runs on a windows 7. tried reinstalling it but it seems nothing has changed same error messages is coming up each time i tried to setup the printer.
View 1 Replies
View Related
Apr 25, 2013
Printer (Brother DPC-150) used to work with Belkin router. After a power cut printer works and router seems to work - on their own. But when I plug printer into USB slot on Belkin the little green light does not come on.
View 1 Replies
View Related
Jul 5, 2011
how to cofiger a network printer in a network, i am using a bsnl broadband connection with user id and psw. all systems are getting internet but printers are not connecting to print.
View 1 Replies
View Related
Jan 28, 2013
I have one router (A) (192.168.0.xxx) that serves as internet gateway. Another two routers (B & C) (192.168.1.xxx & 192.168.2.xxx) that serves two sub-net/network, are connected to this router (A). How can I set it up so that PCs in sub-net C are able to print to network printers in sub-net B? Pls note that I do not have full control over router A.
View 8 Replies
View Related
Feb 12, 2012
I need the ssid or network name to install a printer, and apparently you can find it on the router's setup page. I have a Sagem@Fast 800 E3 - where do I find the setup page?
View 1 Replies
View Related
Sep 26, 2011
when I try to connect my wireless printer, it is asking for the IP address. I type in the same addres that is on my computer, but I get message says computer does not recongize network printer. So I trid two other addresses and those did not work. I am conufsed. How do I knw what address to type in?
View 2 Replies
View Related
Mar 30, 2013
I've got a wireless N home network set up. My wifes PC is connected directly to the cable modem, and our Epson usb printer is connected to her pc. My Toshiba laptop is using a wireless connection. I can see her pc on the network, but cannot see or connect to the printer over the network. Her PC is running Windows 7, mine is running Windows 8 Pro. I was able to print on this printer with my previous pc, which ran Windows 7
View 1 Replies
View Related
Mar 23, 2011
I had to replace my wireless router and when I try to reconnect my printer this is what I get: Your wireless router requires a WEP security key. The security key configured on your printer does not match exactly. Reconfigure your wireless network WEP security key for your printer. Your printer has limited connectivity. Your printer is using IP address 169.254.xx.xxx which is not compatible with the IP address 192.16x.x.x of the pc.I had to changed the WEP security key I used on the old router as the orginal security key had been used by someone without permission. Before this I had no problems using the printer on my old routerI have tried turning everything off and unplugging it but that does not work, I tried resetting the wireless settings on the printer, yet that did not work. I am using Windows Vista service pack 2 on a Compaq Presario laptop, the wireless router is a Netgear N600, and the printer is an HP Photosmart C4740.
View 7 Replies
View Related
Oct 1, 2011
How do I add a Dell wireless printer 968A10 to a home network? The printer was connected to the old (former modem) home network. printer is now not in new network.
View 1 Replies
View Related
