Cisco Routers :: Cannot Get To Devices On Remote Network RV082
Dec 30, 2011
I am able to make a connect to my remote RV082, I can ping the inside network gateway from the remote end but I cannot ping or get to any devices on the remote network, my local network is 192.168.15.x and the remote network is 192.168.0.x I am using WIN 7, and using the native VPN setup in WIN 7, I do a print route and everything looks fine there, I can't figure this out
View 8 Replies
ADVERTISEMENT
Nov 29, 2012
I'm setting up a site-to-site VPN with an RV082 ( and an RV042). The RV042 is behind an Actiontec modem/router that has the local public IP address. So, this address is registered with dyndns so we can find it with a name.
The name is entered into the RV082 VPN Remote Group Setup as: Dynamic IP + Domain Name (FQDN) Authentication The given name for the dynamic IP is entered into Domain Name: But, in the summary, the entry for the Remote Gateway shows only the name and 0.0.0.0 for the IP address.
This same RV082 can get the same IP address from a ping of the name just fine.
View 1 Replies
View Related
Oct 23, 2012
I have a customer that has a Cisco 2900 Series ISR on his Headquarters, and has some branches with RV082s.We have VPN Client configured on the 2900 ISR Router and we can connect remotely using the VPN Client to the Headquarters (192.168.1.0) however we can't reach the branches subnets (192.168.2.0, 192.168.3.0, etc.)... we found out that in the RV082 you need to specify the secure traffic as a destination, but in only supports one network (192.168.1.0 or Headquarters in this case), we can't specify the VPN Client pool defined on the ISR so it can reach the incoming VPN Clients.Is there any way to accomplish this? We need to access the branches subnets when connecting using VPN to the 2900 ISR.
View 1 Replies
View Related
Sep 17, 2012
I have a RV082.I need to disable the firewall, since firewalling is done better elsewhere.However disabling firewall Remote management on wan ip is forcefully enabled.I don't need Remote management, keeping it enabled is a security risk for my setup.I don't understand the rationale behind the choice to forcefully enable remote management if firewall is disabled.Is there a way to disable both firewall and remote management?Or at least a workaround?
I'm on firmware 2.0.0.19-tm on a probably v2 hardware. (Cannot find this info in the web configuration).This is not the newest even for v2 hw but I cannot afford to break it trying to upgrade the firmware.Moreover no release notes for firmware releases refers to a correction of firewall/remote management behavior.Is this behavior also in newer firmware releases?
View 2 Replies
View Related
Jul 25, 2011
I have a RV082 and several of my remote laptops cannot access my server using its domain name. It can be accessed using its internal ip address. The issue is that you can log onto the server using remote access and the ip however you cannot use any shortcuts using the domain name. You can see the server with the domin name however no access path is available. This is only on a few remote user laptops. Others work perfectly.
View 1 Replies
View Related
Oct 9, 2012
I am trying to configure RV082 router with Mac Native VPN Client for my remote access. However, no matter what I did, I am not able to make it works. Can any one can give me an example of how to conguration my RV082 router and Mac Book Pro(Mountain Lion)?
View 2 Replies
View Related
Aug 8, 2012
First time VPN newbie. I need to set up vpn for a friends small business using RV082 so, as a test, I set it up here at my home using a very basic config. The network topology looks like:
cloud => cable modem => RV082 => DIR655 => win7 PC
At a remote site, I fire up QUICKVPN, enter necessary data and successfully connect. Bring up Remote Desktop and put in the IP of my home pc and the logon username and, after a minute or two, it says "unable to connect to the computer" (or words to that effect). My home PC has been configured to allow remote desktop connections and this has occured in the past but not since the RV082 installation. There is nothing in the PC's logs nor in the RV082's logs.
View 1 Replies
View Related
Feb 14, 2013
I've got two RV082's connected. Each has a dynamic IP (changes typically every few weeks). I've configured the tunnels on both ends with a local and remote "Remote/Local Security Gateway Type" of "Dynamic IP + Domain Name(FQDN) Authentication".If I look at the VPN Summary tunnel status, it shows an IP address of "mydomain.dyndns.org 0.0.0.0" under the "Remote Gateway" column heading. The Tunnel Test "Connect" button is N/A.I can resolve both of the mydomain.dyndns.org entries on both sides of each VPN using the Diagnostic DNS lookup tool within each router. If I hardwire a fixed IP address for the Local and Remote Gateway everything works just fine. VPN is good.
I just can't seem to get the "mydomain.dyndns.org" function to work. It appears the router can't resolve the dynamic IP from the domain names on each of the routers.
View 2 Replies
View Related
Nov 4, 2012
I have the RV082 v03 i set it for load balancing i have 2 8gb Adsl modem connected to Wan1 and Wan2
Question how can i assign a certain pc to use the connection on Wan2, what i would like is to assign a specific pc on the network to wan2
View 2 Replies
View Related
Oct 2, 2011
I installed a RV082 at my remote branch and I successfully created a VPN tunnel to my ASA5510 at our core data center.
The PC's that I plug into any of the 8 ports are working fine. However, when I plug in a network printer, it does not work from the network, only from a PC that is also plugged into the RV082, basically locally, using TCPIP
From our data center, I can ping the printer, but the printer shows 'Off-Line'. I even tried to add a TCPIP port, in the printer setup, and it does not see it.
View 1 Replies
View Related
Jan 17, 2013
I want to use WAN2 in DMZ mode on my RV082 router. I want to connect this to a router which will go to another network.
So it will look like this:
LAN1 192.168.188.0
|
|
|
[Code].....
UPDATE: This does not work. In case anyone else tries this, it is not possible with this model of router. The RV082 has to either be in gateway or router mode. In gateway mode, it is doing NAT, and the DMZ will not route correctly to the other LAN. In router mode, the DMZ does route correctly to the other LAN, but the internet will not work because NAT is turned off. We had to add a second RV082 to the configuration to get this working. It cannot be done with 1 RV082.
View 1 Replies
View Related
Apr 19, 2012
Due to bandwith requirements, we need to join a network with a RV016 to a network with an RV082 via a point to point air bridge. (VPN over adls was not cutting it) fortunatelly there is line of sight.
The info
LocationA LocationB
RV016 RV082
WAN1 ADSL modem WAN1 ADSL Modem
WAN2 DedicatedIP modem WAN2 Free
WAN3..7 free
[code]....
We need LAN-B endpoints to be able to reach servers on location A and viceversa.
We pre configured two point to point radios for the tower people to install. (we could change this configs)
Topology (crude sketch)[URL]
Our questions: best port to plug the radios into the RVs WAN ports? switch ports? What rules or static routes need to be created?
View 2 Replies
View Related
Nov 15, 2011
I keep getting an error when trying to use the Microsoft Link layer Topology discovery. It claims there the is either network delays or an incompatible router on the network.
Actual error:
"Responses from other devices on the network are delayed or there is an incompatible router on the network"
I have 2 RV042 routers, one for each of our network connections. So I am assuming this is the source of the error.
View 3 Replies
View Related
Feb 24, 2010
I have recently bought RVS4000 and I'm having problems with remote network computers. I can only access them by IP, by name it always fails. Localy I have BEFSX41, remotely RVS 4000, connected throught VPN. Everything else is working fine.
View 6 Replies
View Related
Aug 7, 2012
We're getting the following message in the logs when we ry to connect: encrypted Informational Exchange message is invalid because it is for incomplete ISAKMP SA
One of the router is a V2 and the other is a V4 if that makes any difference.
View 12 Replies
View Related
Jul 4, 2012
My company is using an RV016 router as a gateway to our internal network. My end goal is to allow remote users to access network shares via Samba.I've been trying to create a VPN using the router with absolutely no luck. I've tried QuickVPN. I've tried creating a client-to-site group vpn. I've tried creating a client-to-site tunnel vpn. I've tried pptp. Nothing will allow me to establish a VPN connection. Sometimes there is information logged in the router but most of the time there is not.
View 1 Replies
View Related
Jan 23, 2013
I have the following config below on my ASA5505, where I want to be able to access remote computers who are VPN'd into the inside network, for support purposes.I want to be able to ping the VPN ip from the LAN, and be able to connect to these computers via the VPN ip. [code]
View 4 Replies
View Related
Sep 27, 2012
I have 4 x 2960 switches in a remote site. These are managed by an NMS in our DC, the NMS IP ends in 35.100 with a /23 mask.
When they are first booted, the switches are visable to the NMS, but after a week or 2, 3 of them drop connection to it. If you reboot them again they are fine. You are able to log onto them form thier local router and use a Radius server which is in the same subnet as the NMS.
The odd thing is, whilst they can not ping the NMS, they are able to ping any other addresses in the 34.0/23 range.
The config on the one that does not lose connection is the same as the other 3 and I have also rebooted the NMS.
View 3 Replies
View Related
Jan 29, 2013
We have an RV082 setup with WAN to the internet and LAN IP of 192.168.188.1.If I add a static route like so:
network: 192.168.166.0
mask: 255.255.255.0
gateway: 192.168.188.2
hop count: 1
interface: LAN
The device with IP 192.168.188.2 will be connected directly to one of the LAN ports on the router.Will that work to route, trying to get to 192.168.166.0 to the IP of 192.168.188.2?It just seems odd because the packets would hit the router then go back out through the LAN port.
View 4 Replies
View Related
Nov 17, 2011
isco epc3925 in transparent bridge provided by isp with following wan details
ip=x.x.x.120 subnet=255.255.255.248 gw=x.x.x.121 and 2 dns server ip's
I can't get the one-to-one nat working. read in some forums that the rv082 can do the job.
View 4 Replies
View Related
May 9, 2013
I have a Meraki Firewall that sits behind my Cisco RV082. The Meraki is setup to run a VPN connection with my server but I am having problems passing the VPN traffic through properly.
I have 2 Uverse Internet Connections that the RV082 using load balancing so that they are shared. I have 10 static IP's.
I am trying to come in on one of my static IP addresses throught the Cisco RV082 to the Meraki and after doing a capture on the meraki it appears that it is starting to receive data to intiate the VPN connection but when it sends data back to the VPN client machine it never makes it.
View 1 Replies
View Related
Nov 12, 2012
I have reset my RV082 router (both wit the reset switch and the factory default wizard) and run the setup wizard but regardless I can't connect to shaw.ca which is my service provider. I notice that if I use http://192.168.1.1 the browsers (IE & FF) default to https://192.168.1.1 and then I am prompted for a certificate. I can enter if I ignore the request but after getting in I simply cannot connect to my ISP.
View 4 Replies
View Related
Jan 12, 2012
Is it possbile to NAT to other subnets with the RV082. It is on a 192.168.41.x and I have a phone system on a 192.168.20.x. After searching all over others are saying no.
View 4 Replies
View Related
Jan 14, 2013
I just set up a new Linksys/Cisco RV082 router with the intent to get VPN working from outside the building. I have gone through the setup and while everything looks good, I have not been able to connect yet. I have tried everything that I know how, and am now hoping to get the answer from some pros.
Here's my setup. We use Comcast Business class internet. The modem is plugged into WAN port 1 on the RV082. I'm using the router as a DHCP server, that is working fine. My local subnet is 192.168.0.0/220
Right now all I want is to be able to log in as a client using QuickVPN. I set up one user and a client to VPN tunnel using the router's config page. Here's the settings I have:
Tunnel Interface is setup on WAN1, checkbox is enabled.
Local Group Setup
Local Security Gatewaytpe: IP Only
Local Security Group Type: Subnet
[Code]....
It seems like something is blocking the connection, but seeing that I have tried this after disabling the firewall completely it doesn't make sense to me. I also went into the config page for the modem and set up the router as a DMZ. I have also tried connecting with the client built into Windows 7, but that doesn't work either, I just get "connection failed with error 619"
I have the port in QuickVPN set to auto, but have tried both 443 and 60443 with same results.
I ran a port scan at [URL] and it shows I have 3 ports open...80,443, and 1723
View 4 Replies
View Related
Jan 24, 2012
I have a VPN tunnel from one RV082 to another, first router has IP range of 192.168.1.0 and the second one has range of 18.18.18.0, the connection works fine, here is where the issue starts, I am at a PC in the 18.18.18.0 network and I ping an IP in the other one e.g. 192.168.1.50 and it pings fine, but when I try to RDP into it or do anything to it I get no response, is it a firewall issue? Is it a NAT issue? I am at a loss, now that IP i mentioned does have RDP enabled and working because it is being port fowarded in the 192.168.1.0 router and I can access it through the public IP.
Also a workstation with a static IP 192.168.1.18 I can ping it if im in the local network but if I am in the remote one I cannot at all.
View 7 Replies
View Related
Jul 28, 2010
we have an RV082 router that a few days ago started restarting itself after normal usage.The simpton is that when people come to office, starting using the Internet the RV082 resets. It stays online for 3 to 12 minutes and then it resets again.
clicking on Reset to Factory Default in the web interfaceafter the reset, I confirmed that it was reset to factory default I reset it again using the reset buttomre-configure the RV082 manually.I also tested with another identical rv082 (hw version and firmware version) and after doing a backup of the config of the original rv082 and restoring it in the new rv082, the same problem happends.
View 20 Replies
View Related
Mar 15, 2013
I have an RV082 10/100 8-Port VPN Router and have configured the NAT table to allow for remote users, however I've run into an issue. It seems like there is a limited number of entries that you can put in the table,10, and I need to configure about 5 more IPs. Any way to expand the NAT table, or alternatively recommend a different router. I would also be willing to add another router to the network, but I have little experience doing that.
View 3 Replies
View Related
Jul 18, 2012
Are the RV042 and RV082 routers SIP AWARE?I haven't had any luck finding documentation stating such.
View 2 Replies
View Related
Oct 20, 2011
Just purchased a RV082 and once I switched a bunch of users over to it I can no longer access the web admin section. I have tried using both IE and Firefox and have used multiple workstations. I get to the login screen but it doesn't get any further. I am running the latest firmware v4.0.4.2-tm. It works for a while then just stops. The only fix is to turn off the device and back on and then it starts working again.
I've seen this issue on other small business cisco devices and had to stop using this because of this issue and switch to a higher grade cisco product but was hoping that this particular issue would have been resolved now across cisco's products.
View 7 Replies
View Related
Jan 9, 2012
I just migrated our office network router to a RV082. While configuring it, I came across three problems:
(1) From our ISP we have four public IP addresses which I want to make use of for outbound traffic. With the previous router we used we could configure LAN IPs(ranges) to map to static public IPs. Does RV082 support this? I could not find an option for that at the web-interface. From what I understand the 1-1 NATing only goes both incoming and outgoign ways and actually is 1-1 and not the many-to-one I am looking for.
(2) How is it possible to configure incoming port forwards to use a specific WAN interface? Will it always be the primary WAN interface?
(3) Does the telnet access provide more configuration options? I could not log in to it with the same user credentials as with the web-interface.
Serial Number : NKS1532xxxxFirmware Version : v4.0.4.02-tm (Jul 4 2011 13:30:56)PID VID : RV082 V03Firmware MD5 Checksum : 1f84d8d0a2a8b99f9bfa4409e64547aaLANWorking Mode : Gateway
View 0 Replies
View Related
Apr 27, 2013
we have a RV082 and have the DMZ option enable for a range of IPs within the same subnet of WAN IP and this works great. I have another range of Public IPs from our ISP that is not in the same subnet of the WAN IP and do not see a way on the RV082 to include this 2nd bank of Public IPs in the DMZ. Our ISP internet feed plugs into the RV082 WAN port and we have a switch pulgged into the DMZ port of the RV082 that is used to connect the public devices in the current DMZ. Both banks of Public IPs from our ISP come over via the ISP internet feed plugged into the WAN Port. My question is, if I cannot configure a DMZ rule to allow this 2nd range of Public IPs to "travel" to the RV082 DMZ port.
View 0 Replies
View Related
Nov 12, 2012
I would like to set the subnet mask off the lan to 255.255.240.0 but the selection menu do not allow to do it.
View 8 Replies
View Related
Sep 25, 2012
I wanted to know if you can connect a Cable modem to a SA520W, then connect a RV082 to the SA520W?
View 5 Replies
View Related