I have recently bought RVS4000 and I'm having problems with remote network computers. I can only access them by IP, by name it always fails. Localy I have BEFSX41, remotely RVS 4000, connected throught VPN. Everything else is working fine.
View 6 RepliesI configured a RVS4000 router to work a VPN terminator for remote users, like traveling or work from home staff. The Cisco quickVPN utility works as it shows VPN connection is successfully connected. However I can not ping any IP address in my office network.
The laptop is windows 7 64bit. The office network subnet is 192.168.1.x/24. Home network subnet is 172.24.105.x/24.I also did "route print" after quickvpn showed me successful but I do not see anyroute about 192.168.1.x.BTW, I openned QuickVPN as administrator and disabled windows firewall while using QuickVPN.
I'm have serveral issues with my router.First, using port 8090, I'm unagle to get remote management of the router.Port 8090 is forwarded to the router 192.168.1.10 I have other issues too, I think the router is blocking my FTP conenction to my NDAS drives.I wish the router would show the UPnP port that are autoamtically added t othe system.Port 80 works well going to my NDAS drives.Firewall, DoS Blocking WAN are all turned off.
View 4 Replies View RelatedI am trying to connect with QuickVPN to my RVS4000 in another location. I get this message: "The remote gateway is not responding. Do you want to wait?'
View 15 Replies View RelatedNetwork running about 60 computers, most of which are running windows 7 professional. Some are on a domain, some are not.At (seemingly) random times, some computer on the network will lose the ability to browse websites (including the web interfaces of networked devices). I can't identify what circumstances cause this to occur. I only find out about it when someone calls me.From the affected computer:I can ping sites I can ping our Cyberoam UTM (which acts as our DNS, DHCP, and firewall)disabling/enabling connection doesn't fix the problem releasing/renewing ip doesn't fix the problem flushing dns doesnt fix the problem uninstalled antivirus on two test machines, problem still randomly manifests.replaced the Cyberoam with newer model users have claimed that if they wait a long period of time (40+ minutes) the problem sometimes resolves.rebooting the computer resolves the issue until it randomly occurs again changing the computer's mac address also resolves the issue until it randomly occurs again.
View 3 Replies View RelatedI'm trying to set up a VPN tunnel between a Linux machine and a RVS4000 at a remote site (served via satellite connection). After many efforts, I finally succeeded (based on Openswan). However, while PINGing is OK, big packets (from the RVS4000 LAN to the Linux box) arrive corrupted.
I lowered the WAN MTU, with no success. What finally did the trick is to lower the MTU at the RVS4000 LAN interface. Since this is not possible via the Web I/F, I did it via telnet ("ifconfig eth0 mtu 1400"). However, this change is lost after router reboot. How can I make the LAN MTU setting permanent?
We have an RVS4000 router at two ends of a VPN tunnel. The VPN tunnel is working fine, however a phone at the remote site drops calls, even though they sound clear and unblemished. I have set highest priority on the port the phone is hooked up to at the remote site, and have set a priority for upload traffic on both routers, but the phone stills drops calls after 2 to 3 minutes.
View 3 Replies View RelatedI want to block everyone from seeing each other on the LAN. So when someone goes to network neighborhood they can't see no one else on EXCEPT for the pritner or so. I want to do this using a Cisco 1841 router. How can I do this?
View 2 Replies View RelatedEverything in our small network worked until today when I had to manually reset the router. We run a application through a provider which requires that we view it from the same IP address for access. We have a statis IP assigned by our ISP solely for this purpose. For simplicity, lets us 23.11.23.176 as the statis assigned by our ISP and 23.11.23.175 as the gateway also assigned by our ISP. The application we need to browse requires that we use the 23.11.23.175 address else it is blocked from viewing. When we hard line into the modem, we are able to browse it fine. When I connect the CISCO router and do it wirelessly, it shows our address as 23.11.23.176 what are the required steps in order to set the CISCO router to use the Gateway address as the browsing IP for computers connected to it. We had set it up about a year ago, and i completely forgot how.
View 2 Replies View Relatedi want to setup a remote desktop connection for 3 computers on the same network to connect to remotely. Originally i was going to port forward the original windows RDP port and run the windows rdp service but learnt that XP Home Edition doesn't support this feature. I want to be able to log onto these computers at any time remotely with the need of accessing the computer before i connect.
View 2 Replies View RelatedI have a CISCO Linksys WRT610N router on my home network which consists of the following 4 computers; Windows Small Business Server 2003, one Windows 7 Ultimate and two Windows XP Professional. How to configure a VPN on the WRT610N router that would allow me to access all of the computers on my home network over the Internet using the "Remote Desktop Connection" component.
View 2 Replies View RelatedI have a RVS4000 at one location and a second RVS4000 at home. I have established an IPSec VPN tunnel between them and it is UP. I can ping the routers from each end no problem. I can ping the IPs listed in the "Local Group Setup" and the "Remote Group Setup" from both ends no problem. I can even open up a shared resource from a Win 7 machine (e.g. by typing \10.10.10.100 in start-run from a computer on my home network).
But - i can't ping anything else on one network from the other. What gives? I need to access a 10.10.10.101 machine but can't even ping it.
- both RVS4000 boxes have latest firmware (V1.3.3.5)
- home RVS4000 setup with IP 10.10.11.1
- home network has a server with IP 10.10.11.20
- other location RVS4000 setup with IP 10.10.10.1
- other location server setup with IP 10.10.10.100
Tunnel settings on home RVS4000 (the other location properly mirror these).
- Local Security Gateway Type : IP Only
- Local Security Group Type : Subnet
[code]....
I have recently purchased a RVS4000 router and am experiencing major downtime.Almost everyday the RVS4000 router losing internet connectivity. I noticed that when this happens I cannot login into the router from my pc which is connected to the RVS4000 network.The only way to restore connectivity is to restart the RVS4000 by disconnecting power and powering back up.The router's WAN is connected to my Cable modem.The RVS400 has two PC connected to it. (port 3 & 4) I have a Cisco 8-port switch connect to the RVS4000 with 3 additional PCs/devices on it.
View 6 Replies View RelatedNeed the solution for aboove
View 19 Replies View RelatedI have Cisco RVS4000 and Linksys Befsx41.I can make a VPN connection when bought are in Static ip-address.RVS in static ip and Linksys in ISP changing ipconnection is not made.
Here is some log:
Feb 9 20:48:17 - [VPN Log]: "xxxxx"[1] xxx.xxx.xxx.185 #4: multiple ipsec.secrets entries with distinct secrets match endpoints: first secret used
Feb 9 20:48:17 - [VPN Log]: "xxxxx"[1] xxx.xxx.xxx.185 #4: multiple ipsec.secrets entries with distinct secrets match endpoints: first secret used
Feb 9 20:48:17 - [VPN Log]: "xxxxx"[1] xxx.xxx.xxx.185 #4: transition from state STATE_MAIN_R1 to state STATE_MAIN_R2
[code]....
I have installed an RV120W router specifically for the VPN capability. I have a small home office with 3 Win7 computers and a SeaGate GoFlex Home NAS drive opperating on the RV120W LAN. I need to allow users to access these networked computers and NAS device over the VPN by mapping their IP locations, such as 192.168.100.155, which is the local IP assigned by the router.
I am able to establish a QuickVPN connection without trouble. I had to set the port to 60443 as it was conflicting with the NAS drive, but this resolved that problem.
I am able to ping the router without any problem over the VPN using the local IP address. I am able to pull up the NAS web portal off the drive via the local IP address using a broswer. Therefore, I know I am talking to the drive via port 443 (I think that is the right port for http). I CANNOT ping the NAS drive over the VPN. I CANNOT ping ANY of the computers or the NAS over the VPN.
Through my reading it appears that a port is being blocked that might need to be opened. But, in the same readings, they say you should use a VPN so that you don't have any issues with blocked ports. I thought I was using a VPN!
I am testing the VPN on a WIN7 Pro laptop with the most current QuickVPN installed. I have also update the firmware on the router to the most current as well.
When I do an ipconfig /all command and look at what I think is the VPN information, there does not appear to be any tunnels established. I don't know if this matters, but thought it odd since I do have a VPN established.
I have enabled PING in the firewall and unchecked the Block Fragment Packets.
I should also note that I can remote manage the router using the 60443 port and an https connection to the local ip address, so clearing there is a connection. SO WHY CAN"T I SEE ANY OF MY WIN 7 COMPUTERS OR MY NAS DRIVE?
I have burned a lot of time on this and without the VPN capabilities, this router does me not good.
I have an RVS4000 setup with a VLAN to a wireless "guest" network, guest network is 192.168.1.x, internal network is 10.0.0.x both have Internet access, and cannot see each other, exactly what I wanted. The only problem is that either from the internal network or the guest network I can no longer access the Remote Web Workplace - [URL] or Outlook Web Access [URL] fails with page not found. Internally I can access via \server emote and \serverexchange but of course this does not work for the guest network. We have Small Business Server 2003. External access if fine.
View 0 Replies View RelatedProblems on RV016 the firmware, Firmware Version : v4.2.1.02 (Jan 18 2012 14:10:55) on port PPPoE mode. It makes the dial, but not Web browsing correctly. The solution was to return the old version of firmware.
View 1 Replies View RelatedCurrently in place ISP WISP Point to Point network would like some pointers to exceed in doing it right. Here are some issues.ISP Fiber 50 Megs down and 50 Megs up ( Working )What Router do I use? Looking at Cisco RVS4000 at JDT Site as main router I have routers at others towers using the 10.1.19.xxx address as wans setup.Do I pull out all routers and use only one from the JDT Site?
a. Due to Port forwarding
b. Lets say main Wan is 74.144.55.159 Lan 10.1.19.1
1. Site BTT router is assign address 10.1.19.33 Lan 192.168.6.1
a. Can I setup 74.144.55.159:85 to see 10.1.19.33?
My Point ot Point radio use different IP address to separate from lan address (10.1.19.xxx) Radios (10.1.119.xxx)1. Everything is working just want to re-design everything never thought I would grow this fast with in 2 years. Hope I explain this well enought. 90% of users are out in the country without high speed internet.
I have a RVS4000 with client VPNs setup and have created all 5 users......trouble I run into is that when one of the users attempts to connect to the VPN from a second device (ie the sixth device to connect to the VPN), the connection does not establish....cannot ping remote server (using QuickVPN). In looking at the logs, the device that isn't working is getting a different IP (172.16 vs 192.168). I know I'm limited to 5 users, but am I limited to 5 devices as well?
View 2 Replies View RelatedI am trying to connect a LAN to the internet via an RVS4000 for remote access to the LAN and cannot connect to the RVS4000. I am using a static WAN address, entered it in the WAN setup area (subnet, gateway, etc.). I do not use DHCP as all the LAN units are static addressed. I rebooted, etc. but cannot see the router externally (I am pinging from a remote site).If I plug my laptop into the WAN cable and set the laptop to the WAN adress, I have no issues. I have checked the cables (all CAT5e shielded), checked both straight through and crossover cables, and have no luck.
View 1 Replies View RelatedIn common with some other reports, I've been having a problem with a keep-alive tunnel between a RV016 and a RV042 not reconnecting if the tunnel is interrupted (by the WAN connection going down). In this event the only remedies are to manually connect the tunnel or to power cycle the routers. The firmware is v4.2.1.02 on both routers.I solved the problem by enabling keep-alive on the RV016 and disabling keep-alive on the RV042. If I set it the other eay around (RV042 keep-alive and RV016 not) then it will not reconnect automatically.
View 6 Replies View RelatedI am being told from my remote end I do not have port 22 opened up. I have single port forwarding to SSH 22 and Port Range 22 enabled.
View 1 Replies View RelatedI have a RV042 (firmware 1.3.13.02-tm). Is it possible to configure so traffic from a specific domain (incl. its sub-domains) is directed exclusively to one WAN port?
View 10 Replies View RelatedI have 2 internet connections in my office one via Verizon Fios and another one via the local cable company. On the fios connection I have an RV042 VPN router and on the Cable company connection I have an rvs4000 router, I would like to know if there is a way I can connect the 2 so I can share a printer I have on one of the 2 networks from the other network without using the VPN feature, like via an ethernet cable connected between the 2 and some kind of static route maybe?
View 6 Replies View Relatedso how can we connect 4 remote computers so dat they can share data,as well as if data is updated on 1 pc ...it is automatically updated on rest 3.....
View 8 Replies View RelatedWell I went to command prompt and typed command ipconfig /all and saw the ip address my system was configured to. Dunno why, but I manually set that ip address in my IPv4 internet settings and got access in my hostel. Now suddenly the access is gone. What should I say, the ip address that I set my laptop to has been shut down ? It doesnt work any more? How do I get another IP address like that which gives me no restricted browsing? What does the admin do in the laptop that suddenly it gets unrestricted browsing privileges?
View 1 Replies View RelatedI am able to make a connect to my remote RV082, I can ping the inside network gateway from the remote end but I cannot ping or get to any devices on the remote network, my local network is 192.168.15.x and the remote network is 192.168.0.x I am using WIN 7, and using the native VPN setup in WIN 7, I do a print route and everything looks fine there, I can't figure this out
View 8 Replies View RelatedI am trying to troubleshoot an issue on our network that is resulting in extremely slow internet browsing. I have found out that the first request in a ping always timesout. Also, having the same issue with running a tracert. I have included some screenshots
View 7 Replies View RelatedIs there anyway that I can access Remote access my computers via the internet browser.
View 4 Replies View RelatedI was trying to access some computers in network via remote desktop. All those computers had been used by other staffs.What I noticed that, for some computers I can access via remote desktop by forcing them to log off (people who were using the computers)But for some computers, I got the message similar to "user is currently logged onto the computer, you are not allowed to connect"I want to force them too and access these computers. How I can do it?
View 6 Replies View RelatedMy company is using an RV016 router as a gateway to our internal network. My end goal is to allow remote users to access network shares via Samba.I've been trying to create a VPN using the router with absolutely no luck. I've tried QuickVPN. I've tried creating a client-to-site group vpn. I've tried creating a client-to-site tunnel vpn. I've tried pptp. Nothing will allow me to establish a VPN connection. Sometimes there is information logged in the router but most of the time there is not.
View 1 Replies View RelatedI've got an RV042 router at home and am connected from my office via the QuickVPN client ver 1.4.1.1.2. I can ping the RV042 and log into the administration page and make changes. However, I can not see other computers on the remote network. I can not ping them. When I open my Network page, I still see the computers on my local network.
All machines are running Windows 7 Ultimate. ISP is Comcast at both locations. WAN IP's are dynamic, but have not changed in over a year. Local IP's on the remote (home) network are static..[url]....