I have a RVS4000 with client VPNs setup and have created all 5 users......trouble I run into is that when one of the users attempts to connect to the VPN from a second device (ie the sixth device to connect to the VPN), the connection does not establish....cannot ping remote server (using QuickVPN). In looking at the logs, the device that isn't working is getting a different IP (172.16 vs 192.168). I know I'm limited to 5 users, but am I limited to 5 devices as well?
I have WAG120N and I want to use ssh tunneling to browse the net.In windows, I have to use a software like putty or xShell to establish a ssh connection to remote server.It works perfectly and I don't have any problem with it.The problem occurs when I want to use this ssh account in linux.At first,connection established without any problem or error.After 2-3 minutes it seems ssh dies and no data transmitted through ssh tunnel.I tried this with Symphony ADSL modem(Wired only) and I have no problem with it.I want to know if there's any specific problem or configuration for WAG120N to solve this problem?I like this modem/router and I don't want to sell it and buy any other modem/ router.I have to mention that usually I use wired connections to WAG120N,but at some cases I need to use its wireless features.
We have two sites, Site-A with a ASA 5520 (Remote Access IPSEC VPN server) at one end and a new ASA 5515-X at Site-B. Users at Site-B are unable to establish a VPN connection to Site-A via Cisco VPN client from behind the new ASA 5515-X. They see the following error:
"Secure VPN Connection terminated locally by the client. Reason 412: The remote peer is no longer responding.
They are able to access the same from home or elsewhere so I believe there is nothing wrong with Site-A ASA vpn config which we have been using for a while now. The new 5515-X (version 8.6) has a very basic config with all outbound traffic allowed. I'm pasting the config below. Do I need to enable/allow anything for it to work?
CISCOASA# sh run: Saved:ASA Version 8.4(3)!hostname CISCOASAenable password xxxxxxxxxxxx encryptedpasswd xxxxxxxxxxxxxx encryptednames!interface Ethernet0/0 nameif outside security-level 0 ip address x.x.x.x 255.255.255.248!interface Ethernet0/1 nameif backup security-level 0 ip address
I have a sky router (Netgear DG834GT), which i have connected a secound router to which is a D link DIR-615 (with DD wrt firmware D4).I can get access to the sky router remotely without any issues even when changing the port number. its the Dlink router i cannot get access to remotely (within the network i can by typing in the dlink's ip address and works). Main router Sky router IP is 192.168.0.1 - Currently the port number is 8081.Secondary router Dlink IP is 192.168.0.2 (Static ip) - currently the port number is 8080.I have tried to configure the ports but it just dont want to open. Ive tried to open the ports on main netgear and tried all the option my dlink for port forwarding. i must be missing something fundametal here.
My modem with single network connectivity (Type I) works fine. I tried to replace with Type II modem (with wifi- and 4 or more ports) for connectivity. I could not establish connection with the server of the service provider. I tried to replace with a different type of typeII modem. Still the same. What could be the reason?I connected the same in a different workplace to a different PC.
We have a VPN using 857 and 877 routers as remote connecting in to a 2800 EZVPN Server.
The VPN is working fine. However, the VPN connections sometimes (after a few hours/days) seem to "freeze". A "show crypt sess" shows the connections as Up/Active, but you can not ping antyhing from remote to server, or visa versa, nor does any traffic flow. I then added a "isakmp keep-alive" on the 2800, which improved the situation a bit, but not as much as I hoped.
On the 877 I then implemented a IP SLA, with Object Tracking and then use a Event Manager to just issue a "clear crypto session" . This solved the problem.
However, what do I do on the 857 ? It does not support Object Tracking or the Event Manager. Is there any other mechanism to monitor and reset these frozen/stale VPN connections automatically ?
I have an issue with a Cisco 4900M switch with a WS-X4908-10G-RJ45 half card. The link connection between a 10Gbase-T server nic and the switch does not establish, i believe it is an auto negotiation problem. The link fluctuates constantly between connected and disconnected when set to auto negotiate. When the 10G half card port groups are configured for 1G connections it does the same. If i hard code the server nic to 1G the link remains up when the port group is at 1G. If i hard code the server nic to 10G the link stay down, i don't think the port speed and duplex can be hard coded on the switch end. I have tried updating the drivers on the server as well as diagnostic tests on the nic, which passed. The 4900M IOS code is version 15.0.2-SG2. If i plug a laptop into the 1G configured port the switch and the laptop negotiate at 1G. Also, i believe, if the 10G server nic is plugged into another 1G only switch the link auto negotiates to 1G as normal. The server nic is an INTEL Server Adapter AT 10G, which became end of life in 2009. I believe the half card came out in 2010.
Device asa 5550 - But can a Client establish a SSL VPN to remote network and devices on the remote network access local network printers? so you got one client one network A that creates a SSL VPN to network B , can network B be configured so that automatic job come across the same ssl vpn to a Different IP?
We have ASA5510 with version 7.x and asdm 5.X, i upgraded it to 8.3 and asdm 6.2, and i got vpn peers 250 and 2 ssl.when i try to connect through client software , i can see in the logs UDP 500 port is created as shown below.Mar 31 2011 23:54:40 302015 18.104.22.168 57013 x.x.x.x 500 Built inbound UDP connection 56694 for outside:22.214.171.124/57013 (126.96.36.199/57013) to identity:x.x.x.x/500 (x.x.x.x/500) no other things are going on , and i get error as shown below.
Secure VPN Connection terminated Locally by the client Reason 412: Remote peer is no longer Responding Connection terminated on.
i am suspecting it is VPN-3DES-AES activation key issue.when i go to Remote Access VPN ---Advanced---SSL Seetings--From Left Encryption Panel Available Algorithems i have DES-SHA1 when i try to drag it tto Right panel of Active algorithems it gives me error *** below [ERROR] sl encryption rc4-sha1 des-sha1 The 3DES/AES algorithms require a VPN-3DES-AES activation key and currently in right panel of Active Algorithms i have only RC4-SHA1,
The DNS comes request timed out while pinging and i am unable to browse. But the Same LAN cable is working fine in another pc. I can ping the Gate way. But not able to ping DNS.Local Network is working fine.
I have a RVS4000 and I would like to setup a Ping monitoring from the outside to a device behind RVS on lan network. I have created a rule to allow a service PING for range from WAN 46.xxx.xxx.xxx - 46.xxx.xxx.xxx to host 192.xxx.xxx.xxx but unfortunately this is not working. I can confirm that I can ping host 192.xxx.xxx.xxx from diagnostics on RVS.
I have created a VPN client account on my RVS4000 router. I have installed Quick VPN on my laptop in the default directory -- Program Files (x86) / Cisco Small Business / Quick VPN Client
I have generated and exported a certificate -- RVS4000_Client.pem -- and placed that in the Program Files (x86) / Cisco Small Business / Quick VPN Client directory. When I attempt to connect using the Quick VPN client, I get the warning "Server's certificate doesn't exist on your local computer."
If I ignore the message I can log in, and ping resources inside the network and log into the router. However, I cannot mount any drives and the router shows that no VPN tunnels exist. I've read several posts here and elsewhere and can't seem to see where I've gone wrong.
I have Cisco RVS4000 and Linksys Befsx41.I can make a VPN connection when bought are in Static ip-address.RVS in static ip and Linksys in ISP changing ipconnection is not made.
Here is some log:
Feb 9 20:48:17 - [VPN Log]: "xxxxx" xxx.xxx.xxx.185 #4: multiple ipsec.secrets entries with distinct secrets match endpoints: first secret used Feb 9 20:48:17 - [VPN Log]: "xxxxx" xxx.xxx.xxx.185 #4: multiple ipsec.secrets entries with distinct secrets match endpoints: first secret used Feb 9 20:48:17 - [VPN Log]: "xxxxx" xxx.xxx.xxx.185 #4: transition from state STATE_MAIN_R1 to state STATE_MAIN_R2
RVS4000 router doesnt give out an IP address to a client connecting with QVPN v1.303, connection seems good, router logs the connection and tracks its duration etc but client side does not get an IP from the RVS4000 side -keeps local LAN ip + there is no access to the remote shares etc. RVS 4000 has DHCP enabled. Client side subnet is different to the VPN side. VPN users are setup correctly (Router logs the user as connected) . Port 443 is not setup in port forwarding.
RVS4000 router doesnt give out an IP address to a client connecting with QVPN v1.303 (or v1.4..- tried that too), connection seems good, router logs the connection and tracks its duration etc but client side does not get an IP from the RVS4000 side -keeps local LAN ip + there is no access to the remote shares etc. RVS 4000 has DHCP enabled. Client side subnet is different to the VPN side. VPN users are setup correctly (Router logs the user as connected) . Port 443 is not setup in port forwarding. (posted in LAN Routing & Switching 2 days ago but I got no response so I thought Id try here !)
I configured a RVS4000 router to work a VPN terminator for remote users, like traveling or work from home staff. The Cisco quickVPN utility works as it shows VPN connection is successfully connected. However I can not ping any IP address in my office network.
The laptop is windows 7 64bit. The office network subnet is 192.168.1.x/24. Home network subnet is 172.24.105.x/24.I also did "route print" after quickvpn showed me successful but I do not see anyroute about 192.168.1.x.BTW, I openned QuickVPN as administrator and disabled windows firewall while using QuickVPN.
Router connects to ISP but cannot browse the Internet. I have updated the firmware to 188.8.131.52 and that did not work. Reset the router to factory settings and that did not work either. Router had worked until the ISP changed the ONT. The router worked initally after the ONT was changed, but that changed sometime during the day as it did not work that night. The ISP gave me a netgear router and that works, so I can connect, but I would rather the RVS4000 would work. I assume a setting at the ISP, but do not know which one. I get an error on the computer "name resolution for the name dns.msftncsi.com timed out after none of the configured DNS servers responded" I can ping, tracert and my little weather gadget works, but a web page will not display
Using the latest Cisco QuickVPN, my Windows 7, 64 bit laptop processes the QuickVPN connection to the point where the laptop attempts to ping the router and verify the connection. Those pings fail.Windows firewall is ON and IPSEC is started on the laptop. I have tried Kaspersky's firewall both enabled and disabled with no change.
I have a RVS4000 at one location and a second RVS4000 at home. I have established an IPSec VPN tunnel between them and it is UP. I can ping the routers from each end no problem. I can ping the IPs listed in the "Local Group Setup" and the "Remote Group Setup" from both ends no problem. I can even open up a shared resource from a Win 7 machine (e.g. by typing \10.10.10.100 in start-run from a computer on my home network).
But - i can't ping anything else on one network from the other. What gives? I need to access a 10.10.10.101 machine but can't even ping it.
- both RVS4000 boxes have latest firmware (V184.108.40.206) - home RVS4000 setup with IP 10.10.11.1 - home network has a server with IP 10.10.11.20 - other location RVS4000 setup with IP 10.10.10.1 - other location server setup with IP 10.10.10.100
Tunnel settings on home RVS4000 (the other location properly mirror these). - Local Security Gateway Type : IP Only - Local Security Group Type : Subnet [code]....
I'm have serveral issues with my router.First, using port 8090, I'm unagle to get remote management of the router.Port 8090 is forwarded to the router 192.168.1.10 I have other issues too, I think the router is blocking my FTP conenction to my NDAS drives.I wish the router would show the UPnP port that are autoamtically added t othe system.Port 80 works well going to my NDAS drives.Firewall, DoS Blocking WAN are all turned off.
I have an RVS4000 setup with a VLAN to a wireless "guest" network, guest network is 192.168.1.x, internal network is 10.0.0.x both have Internet access, and cannot see each other, exactly what I wanted. The only problem is that either from the internal network or the guest network I can no longer access the Remote Web Workplace - [URL] or Outlook Web Access [URL] fails with page not found. Internally I can access via \server emote and \serverexchange but of course this does not work for the guest network. We have Small Business Server 2003. External access if fine.
I have recently bought RVS4000 and I'm having problems with remote network computers. I can only access them by IP, by name it always fails. Localy I have BEFSX41, remotely RVS 4000, connected throught VPN. Everything else is working fine.
As you can see i have problems with connecting 2 SRP521W together for an VPN tunnel. I tried as much as I can but now i dont know what to do or how and where is the mistake? the connection between these two devices was there last week, after weekend (nothing changed in configs) the connection suddenly was interrupted, without any reason or warning. another day it worked again and 20 mins later connection was dead again...and now it wont establish at all.. here are some screenshots from the vpnconfigs of my devices. one has a static IP the otherone uses FQDN. These are the IKE policies: Here the IPsec Policies: and the GRE policies:
I am trying to connect a LAN to the internet via an RVS4000 for remote access to the LAN and cannot connect to the RVS4000. I am using a static WAN address, entered it in the WAN setup area (subnet, gateway, etc.). I do not use DHCP as all the LAN units are static addressed. I rebooted, etc. but cannot see the router externally (I am pinging from a remote site).If I plug my laptop into the WAN cable and set the laptop to the WAN adress, I have no issues. I have checked the cables (all CAT5e shielded), checked both straight through and crossover cables, and have no luck.
I'm trying to set up a VPN tunnel between a Linux machine and a RVS4000 at a remote site (served via satellite connection). After many efforts, I finally succeeded (based on Openswan). However, while PINGing is OK, big packets (from the RVS4000 LAN to the Linux box) arrive corrupted.
I lowered the WAN MTU, with no success. What finally did the trick is to lower the MTU at the RVS4000 LAN interface. Since this is not possible via the Web I/F, I did it via telnet ("ifconfig eth0 mtu 1400"). However, this change is lost after router reboot. How can I make the LAN MTU setting permanent?
We have an RVS4000 router at two ends of a VPN tunnel. The VPN tunnel is working fine, however a phone at the remote site drops calls, even though they sound clear and unblemished. I have set highest priority on the port the phone is hooked up to at the remote site, and have set a priority for upload traffic on both routers, but the phone stills drops calls after 2 to 3 minutes.