We have an RVS4000 router at two ends of a VPN tunnel. The VPN tunnel is working fine, however a phone at the remote site drops calls, even though they sound clear and unblemished. I have set highest priority on the port the phone is hooked up to at the remote site, and have set a priority for upload traffic on both routers, but the phone stills drops calls after 2 to 3 minutes.
View 3 RepliesI'm trying to set up a VPN tunnel between a Linux machine and a RVS4000 at a remote site (served via satellite connection). After many efforts, I finally succeeded (based on Openswan). However, while PINGing is OK, big packets (from the RVS4000 LAN to the Linux box) arrive corrupted.
I lowered the WAN MTU, with no success. What finally did the trick is to lower the MTU at the RVS4000 LAN interface. Since this is not possible via the Web I/F, I did it via telnet ("ifconfig eth0 mtu 1400"). However, this change is lost after router reboot. How can I make the LAN MTU setting permanent?
We have a 100Mbps metro-ethernet link connecting to a remote site. This link is terminating in our 3750-x stack switch.We are getting a LOT of output drop on that interface and our remote IP Phone calls keep going off because of that.I've disabled all kind of QoS, but no luck.
View 16 Replies View RelatedI am try to configure ASA 5510 with 8.3 IOS version.My internal users are 192.168.2.0/24 and i configured dynamic PAT and are all internet .
i want configure identity NAT for remote access VPN.Remote users IP pool is 10.10.10.0 to 10.10.10.10
i know to configure NAT exemption in IOS 7.2 version. But here IOS 8.3 version. configure NAT exemption for 192.168.2.0/24 to my remote pool( 10.10.10.0 to 10.10.10.10).
Recently i bought a Cisco RVS4000, upgraded the firmware to latest stable release (Firmware Version: V2.0.2.7) and started configuring it.Yesterday i found out that as the dsl connection drops (i'm using PPPoE with an ethernet ADSL Modem) the product stops logging, both locally and to an external configured syslog (which resides on a linux box over the LAN).
View 3 Replies View RelatedWe have successfully establish a site-to-site vpn, but we have some difficulties when PPTP users try to access the remote network linked by this tunnel. LAN users can access the remote network without problem, but users who are connected remotly to the lan (PPTP) can't access computer on the remote network. Is there a way to allow PPTP user to access the remote network ? Adding a route ?
View 1 Replies View RelatedI configured a RVS4000 router to work a VPN terminator for remote users, like traveling or work from home staff. The Cisco quickVPN utility works as it shows VPN connection is successfully connected. However I can not ping any IP address in my office network.
The laptop is windows 7 64bit. The office network subnet is 192.168.1.x/24. Home network subnet is 172.24.105.x/24.I also did "route print" after quickvpn showed me successful but I do not see anyroute about 192.168.1.x.BTW, I openned QuickVPN as administrator and disabled windows firewall while using QuickVPN.
I'm have serveral issues with my router.First, using port 8090, I'm unagle to get remote management of the router.Port 8090 is forwarded to the router 192.168.1.10 I have other issues too, I think the router is blocking my FTP conenction to my NDAS drives.I wish the router would show the UPnP port that are autoamtically added t othe system.Port 80 works well going to my NDAS drives.Firewall, DoS Blocking WAN are all turned off.
View 4 Replies View RelatedI have recently bought RVS4000 and I'm having problems with remote network computers. I can only access them by IP, by name it always fails. Localy I have BEFSX41, remotely RVS 4000, connected throught VPN. Everything else is working fine.
View 6 Replies View RelatedI am trying to connect with QuickVPN to my RVS4000 in another location. I get this message: "The remote gateway is not responding. Do you want to wait?'
View 15 Replies View RelatedI'm trying to setup a VPN tunnel between a Cisco RVS4000 on our side and a Cisco ASA5520, to connect a machine on our local network to a test server on the target side.
We have all the settings setup correctly and the tunnel is up and running, however, our local machine can't connect/ping to their server. I've tried a trace route both from the machine and from the RVS4000 itself, and they both get stuck after getting past 192.168.1.1. Is there any routing or NAT-ing that I need to do on our router? Or is there a problem somewhere else?
I have got two CISCO RV042 .I need to configure a site to site VPN .
View 1 Replies View RelatedThe day before yesterday, I bought the dir-615.
I had set an admin password and user's password. It was not same password. In this setting, there was no problem. Sure, no problem at connect from private IP, internet IP or just reboot and anywhere. The problem is the next.
If you got an electronic timer-switch and apply the DIR-615 then you cannot obtain an admin privilege from a remote. It just general user's permission even if I put the admin password.
I have been DIr-615 E4 hardware and 5.10 firmware. It does not happens at local IP address(i.e. 192.168.0.1) but it happen as trying connect from a remote IP address after AC plug re-powered.
I am doing use the AC timer for the remote internet managing at every day. It useful things for the router and IP camera. I need a admin privilege from a internet for the router managing.
About 2 years ago I bought my first laptop and the person I was with recommended my purchasing of a Belkin router. I bought the router, it worked great until this past summer when suddenly whenever somebody called my house phone, my connection was dropped. I was angry cause naturally I have those family members that want to call and talk on the phone with my mother for hours. Eventually I figured out I could work about the problem by hooking the Ethernet cord on my Westel directly to my laptop. Its a temporary fix though in my opinion because this requires me having to sit on the floor against my bed room door and this isn't comfortable, not to mention its also confining, I miss walking around the house with my laptop. Anyway this past weekend I decided to try buying a new Belking N300. This however didn't solve the problem, I still got my signal dropped whenever somebody called the house.
View 14 Replies View RelatedWe have a Cisco Router 3825 which we use to convert phone calls from PSTN to SIP.Can any one suggest us (or point to a documentation) as to how can we use this router as a load balancer (to balance load among different SIP terminals) ?
View 3 Replies View RelatedHow to to successfully configure and connect to a DynDNS account with RVS4000? This was working fine for me until recently when I think I upgraded the firmware to 1.3.3.5.I am trying to connecting to DynDNS.org service. In the past, I used the following string for the Hostname which worked: 'mysubdomain.domain.com&system=custom' (including small quotes). According to the RVS4000 documentation, all you should have to do is specify the host name with DynDNS but this clearly is not accurate.
View 1 Replies View RelatedPurchased the RVS4000 in 11/2012 to work behind a NVG512 in (pass thru mode). I'm running firmware version V2.0.2.7. For whatever reason once or twice a month I lose access to the internet. Sometimes it's AT&T fault but other times my RVS4000 dosen't behave well. I finally took screen shots of every screen I configured in the RVS4000 to make it work in my environment. Last night we lost internet access again. Before unplugging everything I looked in the RVS4000 and found that my WAN setup had reverted back to a default Automatic Configuration - DHCP instead of the Static IP that I had previously saved.
It seems that my RVS4000 is losing just that WAN setting (port forwarding and Static IP Mapping data and VPN client data is still intact.
We have a new deployment where we have 5 total 7921G wifi phones connected via 2 AP541n access points, one connected to a ESW520p switch and then to the UC540 and the other connected directly to the UC540. The wifi phones are intermittently giving no audio when calling each other, however, calls to the PSTN consistently do have 2 way audio. Is this a security issue perhaps? We are running the latest CCA software pack as this is a brand new deployment, also the AP's were upgraded to the latest firmware.
View 14 Replies View RelatedI know the problem lies in the timeout for the default inspection rules. I cannot find where to change this.I have nat statements for 1 to 1 nat to my polycom and tandberg video devices. I have set the firewall for the ouside to in rules to inspect all. This allows the devices to communicate with public addresses, but the video calls drop after 1 hour. How do I change the settings so this does not happen. I have tried setting the rule to allow instead of inspect, but when I do this, I have no access at all. I just want to nat 1 to 1 and allow all traffic to the nated devices. I know this is not secure but it is the only way to allow h323 through to let the video conferencing devices work.
View 1 Replies View RelatedI am unable to ping any device on the internal lan from the opposite side of the tunnel. However, the tunnel connects successfully. I have the firewall disabled on both routers. Site A is using 192.168.3.1 and Site B is using 192.168.4.1. Any thoughts on why I cant ping one router from the other?
View 4 Replies View RelatedMy company just assumed management of a remote entity. The network has several misconfigurations and I need to make some network modifications from my office w/o losing access or incurring lengthy outage to the clients. The network consists of 1721 router and three 2960 switches.
- I only have access to the router from the Internet. I telnet off the router to the 3 switches.
The site uses a single class C 192.168.1.0 / 24. The router is running RIPv2 even though this is the only network. The prior network person (contractor) set up separate native vlans on each switch and all the ports are defined as Native trunk and access are defined to the VLAN interface assigned to the switch. So of course the logs are flooded with Native VLAN mismatch, Each 2960 switch is a VTP server but has no VTP domain.
basic network layout:
Internet => Eth [Cisco 1721] => Fa 0 192.168.1.254 ==> [SW1]
[SW1]
interface Vlan1
no ip address
no ip route-cache!interface Vlan220ip address 192.168.1.219 255.255.255.0no ip route-cache
[code]....
!interface GigabitEthernet0/1description SW2 Gi0/1switchport access vlan 204switchport trunk native vlan 204!interface GigabitEthernet0/2switchport access vlan 204switchport trunk native vlan 204!interface Vlan1no ip addressno ip route-cache!interface Vlan204ip address 192.168.1.224 255.255.255.0no ip route-cache Normally, I would assign the current 192.168.1.254 to a subinterface to Router Fe 0/0 but with each switch having its own native VLAN I am afraid I will lose connectivity to the downstream switches -- my only access is telnet off the Cisco1721 Router.
I have a requirement to create a site to site vpn tunnel on ASA 5510 from a remote site to my HO, ihave already other site-to-site tunnels are up and running on the ASA.The issue is my remote site has got the network address which falls in one of the subnet used in HO(192.168.10.0/24).My requirement is only My remote site need to accees couple of my servers in HO which is in 192.168.200.0/24 subnet.
View 2 Replies View RelatedI originally had a site to site vpn between my pix 515e and RVS4000, but wanted to put my router on the edge of my network for greater QOS control. I've managed to get the tunnel up, but can't get any traffic across the tunnel. The RVS4000 says the tunnel is up, and when I do a "show crypto isakmp sa" on the 2621, I see a QM_IDLE which I believe it good.
My architecture is this:
LAN - RVS4000 (static public ip) ----internet------2621(dynamic public IP ((dhcp)) - LAN
Below is a copy of my 2621 config. My guess is I left something out, but can't put my finger on it.
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
[Code] ....
I am trying to configure a SRP527W for a remote site.It needs to connect back to our Central Office, (via an ASA) which has several VLANs configured. I have entered the configuration for an IKE policy, and one for an IPSec policy (I can only enter one ip/subnet per IPSec policy)When I try to create a 2nd IPSec policy, if I point to the existing IKE policy, I get an error stating "IKE policy has been used by other IPSec policy".If I try to create a new IKE policy, using a different name, but with the same parameters, it shows an error stating the policy is a replica of an existing policy.If I create a new IKE policy, but use a different pre-shared key, then it is accepted by the 2nd IPSec policy, but that would mean I would have to create 2 seperate tunnels on the ASA, each using a different pre-shared key. I have never needed to do this for any of the other routers we have connected.
View 1 Replies View RelatedWe have ordered a pair of Cisco ASA5520 (ASA5520-BUN-K9).Now there is a requirement to terminate site-to-site VPN from remote site. Do we need VPN plus licence for this and how much it cost?
View 1 Replies View RelatedThe scenario where a Site to Site VPN tunnel has been established between Site A and Site B. Lan on Site A can ping Lan on Site B. My problem is a Printer behind Site B needs to be accessed by using the WAN IP address of Site A. Also i could not ping the remote lan or printer from the router.
Below are my configure on the Cisco 877 in site A.
Building configuration...
Current configuration : 5425 bytes
!
! Last configuration change at 15:09:21 PCTime Fri Jun 15 2012 by admin01
!
version 12.4
no service pad
[code]....
cisco products and am struggling getting a VPN going between an ASA 5505 and 5510. I have a VPN created (using the VPN wizward on both) and it shows the VPN is up, but I can't ping the remote site (from either side).
View 11 Replies View RelatedI am configuring Cisco ASA 5520 site to site vpn with Avaya VPN Phone? According to Avaya, the Avaya 9630 phone acts as a VPN client so a VPN router or firewall is not needed.
View 3 Replies View Relatedi have 2 router asa 5505 with base license i wanna make site to site vpn connection and remote site using vpn client to connect first i have hdsl router with 5 public ip i wanna try it by giving 1 public ip to each router and try the vpn but nothing work?
View 1 Replies View RelatedWe have approx 40 branch offices - all of which are connected to a single core site over VPN Tunnels using various gear. At one particular site, we are having issues with the tunnel dropping sporadically throughout the day - some days it happens 10 times, some days it happens none. This just randomly started happening two weeks ago, without any changes taking place. Since it started happening, I have upgraded the code to latest versions, but still the issue persists. This particular site has a 2901 and connects back to a 2951.
Below is the output from:
debug crypto ipsec
debug crypto isakmp
[code].....
I bought 2 RV180 to setup a VPN tunnel between a remote site and central office.The VPN tunnel is established, I can ping from central office to remote site but browsing on that server fails. [code]
Seems the routing is not really working through the VPN Tunnel.
I have a new WRVS4400N configured with a site to site VPN to connect to my office. At the office, we're running a Cisco PIX 515E. I have successfully established an IKE preshared key and the tunnel is listed as Up. I can successfully connect through the VPN tunnel into the office network through the tunnel and all seems good. After some period of time, the tunnel apparently goes into a bad state. Access to the office network is no longer available. When looking at the VPN status screen, the Linksys indicates that the tunnel is up. However, I cannot ping any resources on the office lan. If I disconnect and connect the site to site VPN tunnel, it connects and comes back up successfully. It seems like there is some sort of timeout taking place here. I am running the 1.1.03 firmware.
View 7 Replies View RelatedI just installed a new RV 120W to replace my dlink router.The problem is i cant display the configuration site (192.168.1.1). My internet is working fine and when i go to 192.168.1.1 i can logon (with the password i set using the installation disk) but then i see the top of the config site (blue) but where the config panel should be i see `site cannot be displayed`.
View 4 Replies View Related