Cisco Routers :: RVS4000 Router With No Remote Management?
Jun 30, 2011
I'm have serveral issues with my router.First, using port 8090, I'm unagle to get remote management of the router.Port 8090 is forwarded to the router 192.168.1.10 I have other issues too, I think the router is blocking my FTP conenction to my NDAS drives.I wish the router would show the UPnP port that are autoamtically added t othe system.Port 80 works well going to my NDAS drives.Firewall, DoS Blocking WAN are all turned off.
View 4 Replies
ADVERTISEMENT
Oct 15, 2012
I configured a RVS4000 router to work a VPN terminator for remote users, like traveling or work from home staff. The Cisco quickVPN utility works as it shows VPN connection is successfully connected. However I can not ping any IP address in my office network.
The laptop is windows 7 64bit. The office network subnet is 192.168.1.x/24. Home network subnet is 172.24.105.x/24.I also did "route print" after quickvpn showed me successful but I do not see anyroute about 192.168.1.x.BTW, I openned QuickVPN as administrator and disabled windows firewall while using QuickVPN.
View 7 Replies
View Related
Oct 12, 2011
I have a RVS4000 hardware v2 with firmware 2.0.2.7. I have a DSL modem in bridge mode and have the router set to PPPoE. Everything works fine except I want to use QOS which doesn't work fine. I have some vonage boxes set up on a switch set to port 1 trust mode is set to port and level 4 for highest priority. Port 2 I have on another switch set to priority 3. I tried turning bandwidth mangement on which doesn't seem to work at all so I don't even know if they QOS is even working. I set the max down stream and upstream provided after running a number of speed tests and setting it a little lower than my worst speed results. Once I did that I set up a rule for all traffic for rate control and set them just below the min and max I put in for isp bandwidth. I set the ip range from 192.168.1.100-190 this will cover anything that dhcp hands out and I also have a few statics set up on 192.168.1.180 and 181. However after enabling it I ran some speed tests and I still get full speed and the rules seem to be getting ignored.
View 2 Replies
View Related
Feb 24, 2010
I have recently bought RVS4000 and I'm having problems with remote network computers. I can only access them by IP, by name it always fails. Localy I have BEFSX41, remotely RVS 4000, connected throught VPN. Everything else is working fine.
View 6 Replies
View Related
Apr 4, 2012
I am trying to connect with QuickVPN to my RVS4000 in another location. I get this message: "The remote gateway is not responding. Do you want to wait?'
View 15 Replies
View Related
Jul 21, 2011
I'm trying to set up a VPN tunnel between a Linux machine and a RVS4000 at a remote site (served via satellite connection). After many efforts, I finally succeeded (based on Openswan). However, while PINGing is OK, big packets (from the RVS4000 LAN to the Linux box) arrive corrupted.
I lowered the WAN MTU, with no success. What finally did the trick is to lower the MTU at the RVS4000 LAN interface. Since this is not possible via the Web I/F, I did it via telnet ("ifconfig eth0 mtu 1400"). However, this change is lost after router reboot. How can I make the LAN MTU setting permanent?
View 1 Replies
View Related
Aug 22, 2011
We have an RVS4000 router at two ends of a VPN tunnel. The VPN tunnel is working fine, however a phone at the remote site drops calls, even though they sound clear and unblemished. I have set highest priority on the port the phone is hooked up to at the remote site, and have set a priority for upload traffic on both routers, but the phone stills drops calls after 2 to 3 minutes.
View 3 Replies
View Related
Mar 21, 2012
I'm attempting to configure remote management (and, sometime soon, SNMP) for a newly-deployed WRVS4400N v.2.At the Basic Settings page, I enabled Remote Management, and left the port # at the default. Remotely I entered the public (static) IP for the router in the address bar of IE8 similar to this: 67.203.???.??:8080. IE8's response is, "The webpage cannot be displayed." I'm using a public wi-fi access point, and don't know how the local router is configured, so it's possible that the local router has a blocking rule in the firewall.I'll try again using another remote router that I manage.
View 3 Replies
View Related
Apr 11, 2013
I have a brand new RV042 v3 that I just updated to the latest firmware (v4.2.1.02) and have stumbled across an anomaly... I can only access the router from the WAN port using port 80. I happen to have it set to port 8080, but that doesn't work; I have to use standard port 80.
I have two other RV042 units running older firmware and they work as expected and follow the port that is filled in. This one has me puzzled and wondering if this is a bug in the firmware.
View 2 Replies
View Related
Sep 17, 2012
I have a RV082.I need to disable the firewall, since firewalling is done better elsewhere.However disabling firewall Remote management on wan ip is forcefully enabled.I don't need Remote management, keeping it enabled is a security risk for my setup.I don't understand the rationale behind the choice to forcefully enable remote management if firewall is disabled.Is there a way to disable both firewall and remote management?Or at least a workaround?
I'm on firmware 2.0.0.19-tm on a probably v2 hardware. (Cannot find this info in the web configuration).This is not the newest even for v2 hw but I cannot afford to break it trying to upgrade the firmware.Moreover no release notes for firmware releases refers to a correction of firewall/remote management behavior.Is this behavior also in newer firmware releases?
View 2 Replies
View Related
Nov 24, 2011
i was connected to my rv042 via remote management / browser, and tried to add vpn clients. i generated a new certificate and then i clicked on export for clients. by doing this, the remote management disconnected and i cannot access the router anymore.
how can i get the new .pem file from remote? do i have to make somebody turn off and on the unit to get back remote access??
p.s.: after turning off an on i tried the same steps again: everytime i click on "export for admin" or "export for client", this kills the remote management and the unit must be hardreset. now: how do i get the newly created client certificate off that unit ?? otherwise i will have to drive 350 km just to grep that file ?!?!
View 1 Replies
View Related
Sep 30, 2012
I have a 6 month old RV042 with the newest firmware (v4.2.1.02). Over the weekend I configured the DMZ which after a lot of trial and error, was able to get working. Prior to configuring DMZ, I was able to log in with remote management. However now remote management no longer works. I've tried:
- Rebooting the router
- Turning the firewall off/on
- Turning remote management off/on
- Changing the remote management port
The only step I haven't taken is resetting the router back to factory defaults and trying to reconfigure it all again. This router is so finicky I have no faith I'd be able to get my current functionality back again.
View 2 Replies
View Related
Sep 26, 2011
I just purchased 5 RV220W to act as internet/wireless router at a remote site. There is no VPN, just LAN and Wireless routing to the internet.I have setup remote management and it works fine when I am directly connected to the internet. However, everytime I try to connect through our HTTP/HTTPs proxy farm, it usually fails. Specificially, I get the log-in page and can log in. It starts to render the landing page but redirects to a page stating "Your session has been terminated." On rare instances the first page will appear, however within a few clicks I end up with the same terminated page.
As a test, I bypassed the farm and forced my browser to use one proxy exclusively. At that point I could access the HTTPS interface with no issue. I have not had any issues with other SSL sites with the proxy configuration in use.Is there some sort of MITM prevention I could be running into? If so, can it be turned off.I am new to the RV-series of routers. Is there any logging I could turn on that would provide insight on why the session may be getting terminated?
View 2 Replies
View Related
Feb 11, 2012
I have 25 of these routers installed behind various providers and transport (DSL, Cable, UVerse). At sites where I have static IP, I can't reach any service inside, and in fact can't even reach the router for Remote Management. At all times the users indoes can do whtever they like, the have Internet access.
At sites where we draw a dynamic IP or use PPPoE, I can reach services and manage the router until a known issue stops the inbound traffic.
View 3 Replies
View Related
Aug 28, 2011
My first try at configuring my RV042 has had unexpected results. I set a WAN and LAN address, but did not enable remote managment and did not configure any port forwarding. I expected to be able to connect to the router on the LAN and I could. The surprise came when I put in my web address. I got a router login page. How do I suppress than on the WAN side. I have a static address with my ISP.
View 1 Replies
View Related
May 31, 2012
I am trying to connect a LAN to the internet via an RVS4000 for remote access to the LAN and cannot connect to the RVS4000. I am using a static WAN address, entered it in the WAN setup area (subnet, gateway, etc.). I do not use DHCP as all the LAN units are static addressed. I rebooted, etc. but cannot see the router externally (I am pinging from a remote site).If I plug my laptop into the WAN cable and set the laptop to the WAN adress, I have no issues. I have checked the cables (all CAT5e shielded), checked both straight through and crossover cables, and have no luck.
View 1 Replies
View Related
Apr 30, 2013
I am being told from my remote end I do not have port 22 opened up. I have single port forwarding to SSH 22 and Port Range 22 enabled.
View 1 Replies
View Related
Mar 30, 2012
I have a small issue with Remote Management on my E4200v2.I have enabled it , select https and set Allowed Remote IP Address to any on the default port ( 8080 ).After all of this, I cannot connect to my router from my office or any other place. I'm using DDNS and all its ok ( updated at time ). I've tried also connecting to my direct ip address ( dynamic ) but with no result.P.S. no incoming log from port 443 using https.
View 3 Replies
View Related
Aug 25, 2012
I want to be able to login to a router remotely and foward a port on the router. I thought i saw a spot for remote management but don't know how to use it. I have a dyn account and can create a dns for it.
i setup security dvrs on the internet so clients can see cameras from outside their homes. I would like to be able to login to a router if i need to foward a port or something similar.
View 1 Replies
View Related
May 16, 2013
i have router 2911
pub ip: 121.97.65.61-74
interface gigabitethernet 0/1
ip address 121.97.65.61/28
[Code].....
and other ip will drop/kick/disconnected automatically
how to implement this on access list
View 6 Replies
View Related
Nov 20, 2011
My University has free Internet at student homes, but we need to login by PPTP to get an official, public IPv4 and be able to reach the outside world. The network people at the University says that when the PPTP is up, everything should be open (no firewall of any kind).
have my WRT160NL that gets a 10.10.73.0/23 address from DHCP on WAN port. Currently I have 10.10.74.21. My internal network uses 172.17.17.0/24.My PPTP-server is located at 10.192.1.1 and when I connect, I usually get an IP in the 158.37.73.0/24-range. Currently I have 158.37.73.28. I use DynDNS to make sure I always know the public IP by the host binders.dyndns.info ...
So, I have Remote management enabled with HTTP and HTTPS, any IP and default port 8080. But no response from the outside world seems to go through.If I turn of the "filter ICMP" but keep the SPI Firewall on, I get ping reply from external sources towards my router, but still no HTTP or HTTPS response.I also have a Torrent I try to port forward to to be active, this is 23277, and this is the only thing that keeps coming up in the incoming log on my router.
It's not possible to connect to the routers management over the PPTP-tunnel?And why can't I get the port forward to work .. Same reason? PPTP 158.37.73.28 -> 172.17.17.100 (LAN) won't work?
View 1 Replies
View Related
May 6, 2012
How to get HTTPS to work for local or remote management? Selecting HTTPS for either local or remote doesn't enable HTTPS for me. It still use HTTP.
View 2 Replies
View Related
Feb 2, 2007
We have a RV042. remote management is set to DISABLE - but even after restarting the router i can access the interface remotely over the internet.even when i enable it and change the port to say 5555 i can connect to the web interface using either port 5555 but ALSO on port 80.what's wrong here?the only way to stop that was to create a rule that blocks port 80 on the WAN interface. (btw. could this rule affect LAN users when browsing the web?)
View 7 Replies
View Related
Feb 8, 2012
I have Cisco RVS4000 and Linksys Befsx41.I can make a VPN connection when bought are in Static ip-address.RVS in static ip and Linksys in ISP changing ipconnection is not made.
Here is some log:
Feb 9 20:48:17 - [VPN Log]: "xxxxx"[1] xxx.xxx.xxx.185 #4: multiple ipsec.secrets entries with distinct secrets match endpoints: first secret used
Feb 9 20:48:17 - [VPN Log]: "xxxxx"[1] xxx.xxx.xxx.185 #4: multiple ipsec.secrets entries with distinct secrets match endpoints: first secret used
Feb 9 20:48:17 - [VPN Log]: "xxxxx"[1] xxx.xxx.xxx.185 #4: transition from state STATE_MAIN_R1 to state STATE_MAIN_R2
[code]....
View 1 Replies
View Related
Sep 5, 2011
So, I'm trying to set up a VPN tunnel between two sites. Site A has a RVS4000 as the router to the internet. Site B has a Adtran NetVanta 3200 to convert a frame relay to ethernet, so I can't replace the Adtran. How do I set this up so I can create a tunnel between the two Cisco routers? I have static Internet IP addresses for the Cisco at Site A, the Adtran and Cisco at site B. I have configured the two Ciscos to set up their tunnel and I've been able to establish the tunnel between my house (where I put Cisco B in place of my home router as a test) and the Cisco at Site A. So, I know my tunnel settings are ok (with the exception of IP address changes).
1.) put the Adtran in bridge mode and use the Cisco as the firewall, DHCP, etc. No clue how to do that.
2.) put the Cisco in a DMZ set up on the Adtran. If I do that, it wouldn't really give me access through the VPN to the network, right?
3.) set up static routes between the Adtran and the Cisco? static using the internal IPs or the external ones?
I'm not concerned about Site A since I know the internet works there and the VPN tunnel settings are easy enough to change once I actually get the internet working with the two router combo at site B. [code] I don't care which one does the firewall, NAT, etc. To me it would seem easier to have the Adtran send all traffic to the Cisco, then let the Cisco do the rest (VPN, firewall, DHCP, DNS, etc.).
View 3 Replies
View Related
Feb 21, 2012
Trying to set up the Cisco VPN router for remote acces to our network.We have ATT Uverse DSL and it is a Motorola Router, i think NGT 510.the Uverse router has very limited setup options.I cannot set it up as a bridge.The only thing I can figure out is to set the ip passthrough option to the VPN router.We have a static ip address for our internet service.
I have tried several setup and connection options, but cannot get it to work.
1. How to physically connect the routers and network devices?
2. How to setup both routers to play nice.
View 1 Replies
View Related
May 24, 2012
I currrently have the RVS4000 and am looking at the RV180, but I'm having an issue with the RV180 supporting the Dynamic DNS service I need (see here). In that discussion, it seems what would be ideal for me is a router running IOS so I could customize the Dyanmic DNS client on there to fit my needs. However, is there any "affordable" router running IOS that's similar to the RV180 tailored to a small business without getting an overkill router?
Here's my basic needs:Router either compatible with DNS Made Easy's Dynamic DNS service OR has the ability to customize the Dynamic DNS client on there so I can adapt it for DNS Made Easy.I DO NOT need wireless. We only need Ethernet/wired.I prefer Gigabit Ethernet.We're not currently using ProtectLink, so if it offers the ability for it, great, if not, fine.We have our own VPN service and don't need to access the network remotely (just remote into one device using Dynamic DNS), so if it has built-in VPN, great, if not, fine.I'd like IPS included. Our RVS4000 has it and I like this feature.We're switching to cable broadband and VOIP through our cable company, so QoS should probably be included.
View 45 Replies
View Related
Apr 8, 2012
I have an RVS4000 setup with a VLAN to a wireless "guest" network, guest network is 192.168.1.x, internal network is 10.0.0.x both have Internet access, and cannot see each other, exactly what I wanted. The only problem is that either from the internal network or the guest network I can no longer access the Remote Web Workplace - [URL] or Outlook Web Access [URL] fails with page not found. Internally I can access via \server emote and \serverexchange but of course this does not work for the guest network. We have Small Business Server 2003. External access if fine.
View 0 Replies
View Related
Apr 20, 2012
I have multiple remote sites connected back into my infrastructure via satellite. I'm building a GRE tunnel accross this satellite infrustructure to my user's routers. I'm using EIGRP through these tunnels and everything is working great as far as connectivity to my users is concerned. However, with each of these packages, I would like to be able to remotely manage the satellite modem. My problem is that these modems all have the same web management IP address (192.168.1.1:80) and I can't change them. I thought to myself, "too easy, this sounds like an excellant case for NAT!" Either I'm tackling this thing all wrong or something because I can't seem to get it to work. Here is what I've so far (IPs modified and extra info cut[CODE]
View 3 Replies
View Related
Sep 6, 2012
I have a RVS4000 with client VPNs setup and have created all 5 users......trouble I run into is that when one of the users attempts to connect to the VPN from a second device (ie the sixth device to connect to the VPN), the connection does not establish....cannot ping remote server (using QuickVPN). In looking at the logs, the device that isn't working is getting a different IP (172.16 vs 192.168). I know I'm limited to 5 users, but am I limited to 5 devices as well?
View 2 Replies
View Related
Dec 5, 2011
Any possibility remotely manage cisco 876? Remotelly I mean by connecting to WAN IP (DSL interface) from outside. It could be via CCP, telnet or ssh doesn't matter.
View 4 Replies
View Related
Jan 4, 2012
how to setup remote management...
View 4 Replies
View Related
Mar 29, 2012
I do have problems with remote management of a Wireless Accespoint WAP200.The WAP200 is connected to a router RVS4000 and works well..There are several nodes in the LAN, all static IP, all forwarded in the RVS4000..All nodes can be managed in the LAN as well as from outside..Exept the WAP200, from inside in LAN no problem, but from outside gives a 404 return.I build other similar LAN's, but the same, no connection.
View 8 Replies
View Related
