Cisco Routers :: Rv042 Remote Management Unavailable After Certificate Export
Nov 24, 2011
i was connected to my rv042 via remote management / browser, and tried to add vpn clients. i generated a new certificate and then i clicked on export for clients. by doing this, the remote management disconnected and i cannot access the router anymore.
how can i get the new .pem file from remote? do i have to make somebody turn off and on the unit to get back remote access??
p.s.: after turning off an on i tried the same steps again: everytime i click on "export for admin" or "export for client", this kills the remote management and the unit must be hardreset. now: how do i get the newly created client certificate off that unit ?? otherwise i will have to drive 350 km just to grep that file ?!?!
View 1 Replies
ADVERTISEMENT
Apr 11, 2013
I have a brand new RV042 v3 that I just updated to the latest firmware (v4.2.1.02) and have stumbled across an anomaly... I can only access the router from the WAN port using port 80. I happen to have it set to port 8080, but that doesn't work; I have to use standard port 80.
I have two other RV042 units running older firmware and they work as expected and follow the port that is filled in. This one has me puzzled and wondering if this is a bug in the firmware.
View 2 Replies
View Related
Sep 30, 2012
I have a 6 month old RV042 with the newest firmware (v4.2.1.02). Over the weekend I configured the DMZ which after a lot of trial and error, was able to get working. Prior to configuring DMZ, I was able to log in with remote management. However now remote management no longer works. I've tried:
- Rebooting the router
- Turning the firewall off/on
- Turning remote management off/on
- Changing the remote management port
The only step I haven't taken is resetting the router back to factory defaults and trying to reconfigure it all again. This router is so finicky I have no faith I'd be able to get my current functionality back again.
View 2 Replies
View Related
Aug 28, 2011
My first try at configuring my RV042 has had unexpected results. I set a WAN and LAN address, but did not enable remote managment and did not configure any port forwarding. I expected to be able to connect to the router on the LAN and I could. The surprise came when I put in my web address. I got a router login page. How do I suppress than on the WAN side. I have a static address with my ISP.
View 1 Replies
View Related
Jan 26, 2012
When I attempt to export the certificate for the quickvpn client via the router web interface, it looks as if the export works, and it asks me to save the zip file. However, upon opening the zip file I receive the error: The compressed folder is invalid or corrupted.
This happens in multiple browsers, from multiple machines.
View 1 Replies
View Related
Feb 2, 2007
We have a RV042. remote management is set to DISABLE - but even after restarting the router i can access the interface remotely over the internet.even when i enable it and change the port to say 5555 i can connect to the web interface using either port 5555 but ALSO on port 80.what's wrong here?the only way to stop that was to create a rule that blocks port 80 on the WAN interface. (btw. could this rule affect LAN users when browsing the web?)
View 7 Replies
View Related
Jan 28, 2013
RV042 router is giving out the outer certificate instead of server certificate. Outlook anywhere is failing and we are receiving certificate errors for any secure site behind this firewall. I'm not talking about remote management. I'm talking about people trying to access our web site, which is secured, and getting an error because the RV042 is giving its own SSL certificate instead of the Server's certificate. Firmware Version: 1.3.13.02-tm. I don't see any updates for that hardware. I do have it working on an RV042 with the same firmware at a different location. How do we turn that off or keep it from happening? Output from a test site Attempting to resolve the host name xxxx in DNS.The host name resolved successfully. Additional DetailsTesting TCP port 443 on host xxxx to ensure it's listening and open. The port was opened successfully. Testing the SSL certificate to make sure it's valid. The SSL certificate failed one or more certificate validation checks. Test Steps ExRCA is attempting to obtain the SSL certificate from remote server xxxx on port 443. ExRCA successfully obtained the remote SSL certificate. Additional Details Remote Certificate Subject:
SN=California, L=Irvine, C=US, O="Cisco-Linksys, LLC", OU=RV042, CN=68:ef:bd:b8:0f:78, Issuer: SN=California, L=Irvine, C=US, O="Cisco-Linksys, LLC", OU=RV042, CN=68:ef:bd:b8:0f:78.Validating the certificate name. Certificate name validation failed. Tell me more about this issue and how to resolve it Additional Details Host name xxxx doesn't match any name found on the server certificate SN=California, L=Irvine, C=US, O="Cisco-Linksys, LLC", OU=RV042, CN=68:ef:bd:b8:0f:78.
View 1 Replies
View Related
Nov 28, 2012
Just installed RV042 router. And it's giving out router certificate instead of server certificate so people who are trying to access our secured server are getting errors. I'm not talking about remote management. I'm talking about people trying to access our web site, which is secured, and getting an error because the RV042 is giving its own SSL certificate instead of the Server's certificate. How do we turn that off or keep it from happenning?
The RV042 firm version is v4.0.0.07-tm (Aug 19 2010 19:19:50)
View 5 Replies
View Related
Mar 14, 2011
I'm moving from a 5505 to a 5520 and moving to a different location. I have a certificate on the 5505 that I want to export to the 5520.Can I export that key/certificate and import to the new ASA? Is there a problem since its a different location with a different IP ? (Domain name is the same, I moved the name on the DNS also)Do a have to re-do the signing process with the CA ?
View 3 Replies
View Related
Jan 2, 2012
I have set the RV042 up for QuickVPN access. The router config recommends turning HTTPS on in the firewall when using QuickVPN. The side effect to this is any web browser throws me certificate errors and warns me not to continue logging in to the router's config. How do I fix this so the browser does not throw these messages?
Router is Linksys-branded, using latest firmware for this hardware (1.3.13.02-tm)
View 12 Replies
View Related
Mar 21, 2012
I'm attempting to configure remote management (and, sometime soon, SNMP) for a newly-deployed WRVS4400N v.2.At the Basic Settings page, I enabled Remote Management, and left the port # at the default. Remotely I entered the public (static) IP for the router in the address bar of IE8 similar to this: 67.203.???.??:8080. IE8's response is, "The webpage cannot be displayed." I'm using a public wi-fi access point, and don't know how the local router is configured, so it's possible that the local router has a blocking rule in the firewall.I'll try again using another remote router that I manage.
View 3 Replies
View Related
Jun 30, 2011
I'm have serveral issues with my router.First, using port 8090, I'm unagle to get remote management of the router.Port 8090 is forwarded to the router 192.168.1.10 I have other issues too, I think the router is blocking my FTP conenction to my NDAS drives.I wish the router would show the UPnP port that are autoamtically added t othe system.Port 80 works well going to my NDAS drives.Firewall, DoS Blocking WAN are all turned off.
View 4 Replies
View Related
Sep 17, 2012
I have a RV082.I need to disable the firewall, since firewalling is done better elsewhere.However disabling firewall Remote management on wan ip is forcefully enabled.I don't need Remote management, keeping it enabled is a security risk for my setup.I don't understand the rationale behind the choice to forcefully enable remote management if firewall is disabled.Is there a way to disable both firewall and remote management?Or at least a workaround?
I'm on firmware 2.0.0.19-tm on a probably v2 hardware. (Cannot find this info in the web configuration).This is not the newest even for v2 hw but I cannot afford to break it trying to upgrade the firmware.Moreover no release notes for firmware releases refers to a correction of firewall/remote management behavior.Is this behavior also in newer firmware releases?
View 2 Replies
View Related
Sep 26, 2011
I just purchased 5 RV220W to act as internet/wireless router at a remote site. There is no VPN, just LAN and Wireless routing to the internet.I have setup remote management and it works fine when I am directly connected to the internet. However, everytime I try to connect through our HTTP/HTTPs proxy farm, it usually fails. Specificially, I get the log-in page and can log in. It starts to render the landing page but redirects to a page stating "Your session has been terminated." On rare instances the first page will appear, however within a few clicks I end up with the same terminated page.
As a test, I bypassed the farm and forced my browser to use one proxy exclusively. At that point I could access the HTTPS interface with no issue. I have not had any issues with other SSL sites with the proxy configuration in use.Is there some sort of MITM prevention I could be running into? If so, can it be turned off.I am new to the RV-series of routers. Is there any logging I could turn on that would provide insight on why the session may be getting terminated?
View 2 Replies
View Related
Feb 11, 2012
I have 25 of these routers installed behind various providers and transport (DSL, Cable, UVerse). At sites where I have static IP, I can't reach any service inside, and in fact can't even reach the router for Remote Management. At all times the users indoes can do whtever they like, the have Internet access.
At sites where we draw a dynamic IP or use PPPoE, I can reach services and manage the router until a known issue stops the inbound traffic.
View 3 Replies
View Related
Jun 27, 2012
I have configured a VPN tunnel between two remote locations using static IP addresses on two RV042 routers. The tunnel seems to work but the problem is that when the two hosts attempt to ping each other only one can successfully ping. One PC with IP address 192.168.1.100 can ping across the network but the second PC with IP address 192.168.2.100 cannot. These are laptops seperate from the intranet used to test the tunnel. Someone had suggested NAT may be the issue so I enabled NAT Transverse on the routers but still no luck. The following is the results from a ping test.
PC 1
ping 192.168.2.1
Pinging 192.168.2.1 with 32 bytes of data:
Reply from 192.168.2.1: bytes=32 time=116ms TTL=63
[Code] ......
View 1 Replies
View Related
Feb 27, 2013
I recently replaced a Netgear router with a RV042 because I figured out my Netgear was choking my 24MB Uverse connection down to about 6MB. I had VPN setup with my business partner who was already using an RV042 and everyting works fine. However after I setup the RV042 on my side we have not been able to get the VPN up. The settings are as follows
Local Group
Local Security Gateway Type: IP Only
Local Security Group Type : Subnet
IP Address: 192.168.0.0
Subnet: 255.255.255.0
Remote Group
Remote Security Gateway Type: IP Only
remote Security Group Type : Subnet
IP Address: 10.0.0.0
[Code]....
View 1 Replies
View Related
May 9, 2012
Today I installed a new SSL certificate for the management website. After the install the management process continues to hang in initializing.
I can stop the process and start the process again but it never gets passed initalizing.
View 1 Replies
View Related
Mar 6, 2011
I need to enable Management access to FWSM using CA ssl certificate.
FWSM Version 3.2(5) in Cisco 6509 switch.
Got to know how to generate, import and export certificate but my query is how to get it applied to the management ip do i need to apply in the management interface.
View 1 Replies
View Related
Mar 1, 2013
I just acquire the RV042.We have a DSL [WAN1 :download good, bad uplaod] and an SDSL line 4MB OVH [WAN2].
Receive all downstream traffic to WAN1Send email upstream traffic to WAN1Send upstream traffic to OVH and guarantee good bandwidth to 10 TSE access and webex traffic
I built the following rules:
The problem ... nothing works ... the downstream traffic comes from WAN2 and upload on WAN1 or WAN2.
View 1 Replies
View Related
Feb 11, 2013
got the ac900db router set up and the the setup page to allow me to set security is no longer available and i am now unprotected with my wi-fi for a guest login.....website for belkin is a viscious loop that explains NOTHING at all and has no easy way to find how to fix anything!! how do i get to the DASHBOARD or even log back into my account i set up?
View 1 Replies
View Related
Apr 20, 2012
I have multiple remote sites connected back into my infrastructure via satellite. I'm building a GRE tunnel accross this satellite infrustructure to my user's routers. I'm using EIGRP through these tunnels and everything is working great as far as connectivity to my users is concerned. However, with each of these packages, I would like to be able to remotely manage the satellite modem. My problem is that these modems all have the same web management IP address (192.168.1.1:80) and I can't change them. I thought to myself, "too easy, this sounds like an excellant case for NAT!" Either I'm tackling this thing all wrong or something because I can't seem to get it to work. Here is what I've so far (IPs modified and extra info cut[CODE]
View 3 Replies
View Related
Dec 5, 2011
Any possibility remotely manage cisco 876? Remotelly I mean by connecting to WAN IP (DSL interface) from outside. It could be via CCP, telnet or ssh doesn't matter.
View 4 Replies
View Related
Jan 4, 2012
how to setup remote management...
View 4 Replies
View Related
Mar 29, 2012
I do have problems with remote management of a Wireless Accespoint WAP200.The WAP200 is connected to a router RVS4000 and works well..There are several nodes in the LAN, all static IP, all forwarded in the RVS4000..All nodes can be managed in the LAN as well as from outside..Exept the WAP200, from inside in LAN no problem, but from outside gives a 404 return.I build other similar LAN's, but the same, no connection.
View 8 Replies
View Related
Aug 22, 2012
unresponsive / lockups with Cisco ASA 5505 remote management ?
I think it happens like this:
1) With ASDM (Java Web Start), add new crypto map (it could be anything, just happens to be what i added the last time this happened)
2) Click apply
3) ASDM hangs (at this point the Java client becomes entirely unresponsive)
4) ASDM.jnlp refuses to connect and eventually timeout dialog appears. However, VPN connections are still accepted.
5) After a few hours (over night), the ASA refuses all incoming traffic including VPN connections.
View 5 Replies
View Related
May 21, 2012
I have a remote ASA5505 running 8.4(3) with a working site 2 site VPN tunnel to my main office. (The main office is running an ASA 5510 with OS 8.4.3 as well). The encryption domain is all private IP on main site vs. 172.16.10.0/23 on remote site.
Relevant config of the remote ASA:
interface Vlan1
nameif inside
security-level 100
[Code].....
I can manage the ASA on the outside interface (outside of the site 2 site VPN) using the TACACS credentials I can also ping my management station from the ASA using the inside interface, but as stated, the other way around does not work. I have not yet tested if management from the local 172.16.10.0/23 subnet works, but I will try this next.
View 5 Replies
View Related
Mar 1, 2011
I can access the admin pages from inside the network.I can access the admin pages remotely from my iphone (safari).If I try and access them from my PC at work (IE6 or Google Chrome), I can access the router, give the password and get the status screen. But if I try and go to any other page on the router, it asks for the password again and takes me back to the status screen.I have Hardware B1 and firmware 2.0 (not upgraded it yet).
View 1 Replies
View Related
Apr 26, 2010
I am having trouble accessing my DIR-655 remote management screen via ip to my network.To make sure i didnt have any odd settings, i did a hard reset on my router first.I then enabled remote management, and left the default port 8080 I try to access viw the ip address on my status page suffixed by the port 8080 [URL] page cannot be found.I then enabled https and tried to access via:[URL]page cannot be found.I then setup a entry in the virtual server to redirect http requests to my workstation hosting IIS7, if i connect to localhost, the iis welcome screen appears, but if i browse to my ip, i get nothing.I am using Cox residential service, i called them and they informed me that they do not filter or block requests in any way.
View 12 Replies
View Related
Mar 30, 2012
I have a small issue with Remote Management on my E4200v2.I have enabled it , select https and set Allowed Remote IP Address to any on the default port ( 8080 ).After all of this, I cannot connect to my router from my office or any other place. I'm using DDNS and all its ok ( updated at time ). I've tried also connecting to my direct ip address ( dynamic ) but with no result.P.S. no incoming log from port 443 using https.
View 3 Replies
View Related
Aug 25, 2012
I want to be able to login to a router remotely and foward a port on the router. I thought i saw a spot for remote management but don't know how to use it. I have a dyn account and can create a dns for it.
i setup security dvrs on the internet so clients can see cameras from outside their homes. I would like to be able to login to a router if i need to foward a port or something similar.
View 1 Replies
View Related
May 16, 2013
i have router 2911
pub ip: 121.97.65.61-74
interface gigabitethernet 0/1
ip address 121.97.65.61/28
[Code].....
and other ip will drop/kick/disconnected automatically
how to implement this on access list
View 6 Replies
View Related
Feb 25, 2013
Region : Malaysia
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 1.1 v0005.0 Build 120926 Rel.27100n
ISP : TM
The Remote Management Port is not working correctly. For whatever port I set, it will uses port 80 to access.
View 2 Replies
View Related
