Cisco Routers :: RV042 After Configuring DMZ / Remote Management Stopped Working
Sep 30, 2012
I have a 6 month old RV042 with the newest firmware (v4.2.1.02). Over the weekend I configured the DMZ which after a lot of trial and error, was able to get working. Prior to configuring DMZ, I was able to log in with remote management. However now remote management no longer works. I've tried:
- Rebooting the router
- Turning the firewall off/on
- Turning remote management off/on
- Changing the remote management port
The only step I haven't taken is resetting the router back to factory defaults and trying to reconfigure it all again. This router is so finicky I have no faith I'd be able to get my current functionality back again.
View 2 Replies
ADVERTISEMENT
Apr 11, 2013
I have a brand new RV042 v3 that I just updated to the latest firmware (v4.2.1.02) and have stumbled across an anomaly... I can only access the router from the WAN port using port 80. I happen to have it set to port 8080, but that doesn't work; I have to use standard port 80.
I have two other RV042 units running older firmware and they work as expected and follow the port that is filled in. This one has me puzzled and wondering if this is a bug in the firmware.
View 2 Replies
View Related
Jan 6, 2012
I've had 1 to 1 NAT setup for years now with no issues and the other day it simply stopped working. Rebooted everything, had ISP clear arp on their cable modem yet nothing going. As soon as I remove the 1 to 1 NAT on the router the PC has internet access. Add the 1 to 1 back and no out going internet. The configuration is pretty basic and has not changed.Thinking it could be a hardware issue I swapped it out with another RV042 I have with the exact config, same thing 1 to 1 NATs have no internet access. Upgraded one of the RV042 firmware to Firmware Version: 1.3.13.02-tm, had cable modem replaced, spent numerous calls with ISP. nada
I have found one interesting thing however, any internal machine which is set to dhp works fine, and static ip that does not have a 1 to 1 nat works fine and the last ip in the 1 to 1 nat range works fine. If I extend the range it is always only the last ip that works. Even if I add 1 to 1 nats one line at a time, it is always the last entry that works..
View 4 Replies
View Related
Nov 24, 2011
i was connected to my rv042 via remote management / browser, and tried to add vpn clients. i generated a new certificate and then i clicked on export for clients. by doing this, the remote management disconnected and i cannot access the router anymore.
how can i get the new .pem file from remote? do i have to make somebody turn off and on the unit to get back remote access??
p.s.: after turning off an on i tried the same steps again: everytime i click on "export for admin" or "export for client", this kills the remote management and the unit must be hardreset. now: how do i get the newly created client certificate off that unit ?? otherwise i will have to drive 350 km just to grep that file ?!?!
View 1 Replies
View Related
Aug 28, 2011
My first try at configuring my RV042 has had unexpected results. I set a WAN and LAN address, but did not enable remote managment and did not configure any port forwarding. I expected to be able to connect to the router on the LAN and I could. The surprise came when I put in my web address. I got a router login page. How do I suppress than on the WAN side. I have a static address with my ISP.
View 1 Replies
View Related
May 16, 2012
My organization has deployed 3 Cisco RV042 (v3) at our 3 sites. They have been working pretty well up until about a week ago. One of them continues to route traffic and perform port-forwarding, but the VPN has completely stopped working and I can no longer access the web administration interface. I get the standard login page, but any attempt to login (with correct or incorrect password) takes maybe 5 minutes with a spinning status icon, followed by a blank page leaving the browser at: url...
I have the router logs e-mailed to me, and I can see that the system boots up with Jan 1 2010 as the system date, but it eventually gets the correct date from NTP, so I'm doubting this is causing the problem.
These were working for months prior to this happening, and even a reboot of the affected RV042 does not allow me to log into it or setup the VPN tunnels. I have found similar threads on this forum: url...
View 2 Replies
View Related
Jun 24, 2012
After I have upgraded our ASA 5510 to 8.4.2 I have problem with the management interface.Our former firmware 8.2.3 had no problem using the management interface as a DMZ zone, but after we upgraded to 8.4.2 we can't make it work.The interface and the protocol is up, when I type: show interface.But when I ping the interface from a computer connectet to the interface, nothing happens.
Even the logging shows nothing.
View 7 Replies
View Related
Feb 2, 2007
We have a RV042. remote management is set to DISABLE - but even after restarting the router i can access the interface remotely over the internet.even when i enable it and change the port to say 5555 i can connect to the web interface using either port 5555 but ALSO on port 80.what's wrong here?the only way to stop that was to create a rule that blocks port 80 on the WAN interface. (btw. could this rule affect LAN users when browsing the web?)
View 7 Replies
View Related
Mar 30, 2012
My computer stopped being able to Remote Desktop to my server on my network. My backup software also doesn't recognize my server. But, I can access its folders using Windows Explorer. Any other PC on the network can remote desktop to the server and connect. What happened to my machine? This message appears when i try to connect: "Remote Desktop can't connect to the remote computer for one of the following reasons:
1) Remote access tot he server is not enabled
2) The remote computer is turned off
3)The remote computer is not available on the network
Make sure the remote computer is turned on and connected to the network, and that remote access is enabled."
My computer is:
AMD: Athlon 64 X2 5200+ 2991 MHz
Mobo: Gigabyte M57SLI-S4 v.2
RAM: 4GB Mushkin DDR2 PC2-6400
OS: Win 7 64bit
VC: Geforce GTX 470
View 1 Replies
View Related
Mar 1, 2011
I can access the admin pages from inside the network.I can access the admin pages remotely from my iphone (safari).If I try and access them from my PC at work (IE6 or Google Chrome), I can access the router, give the password and get the status screen. But if I try and go to any other page on the router, it asks for the password again and takes me back to the status screen.I have Hardware B1 and firmware 2.0 (not upgraded it yet).
View 1 Replies
View Related
Feb 25, 2013
Region : Malaysia
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 1.1 v0005.0 Build 120926 Rel.27100n
ISP : TM
The Remote Management Port is not working correctly. For whatever port I set, it will uses port 80 to access.
View 2 Replies
View Related
Mar 21, 2012
I'm attempting to configure remote management (and, sometime soon, SNMP) for a newly-deployed WRVS4400N v.2.At the Basic Settings page, I enabled Remote Management, and left the port # at the default. Remotely I entered the public (static) IP for the router in the address bar of IE8 similar to this: 67.203.???.??:8080. IE8's response is, "The webpage cannot be displayed." I'm using a public wi-fi access point, and don't know how the local router is configured, so it's possible that the local router has a blocking rule in the firewall.I'll try again using another remote router that I manage.
View 3 Replies
View Related
Jun 30, 2011
I'm have serveral issues with my router.First, using port 8090, I'm unagle to get remote management of the router.Port 8090 is forwarded to the router 192.168.1.10 I have other issues too, I think the router is blocking my FTP conenction to my NDAS drives.I wish the router would show the UPnP port that are autoamtically added t othe system.Port 80 works well going to my NDAS drives.Firewall, DoS Blocking WAN are all turned off.
View 4 Replies
View Related
Sep 17, 2012
I have a RV082.I need to disable the firewall, since firewalling is done better elsewhere.However disabling firewall Remote management on wan ip is forcefully enabled.I don't need Remote management, keeping it enabled is a security risk for my setup.I don't understand the rationale behind the choice to forcefully enable remote management if firewall is disabled.Is there a way to disable both firewall and remote management?Or at least a workaround?
I'm on firmware 2.0.0.19-tm on a probably v2 hardware. (Cannot find this info in the web configuration).This is not the newest even for v2 hw but I cannot afford to break it trying to upgrade the firmware.Moreover no release notes for firmware releases refers to a correction of firewall/remote management behavior.Is this behavior also in newer firmware releases?
View 2 Replies
View Related
Sep 26, 2011
I just purchased 5 RV220W to act as internet/wireless router at a remote site. There is no VPN, just LAN and Wireless routing to the internet.I have setup remote management and it works fine when I am directly connected to the internet. However, everytime I try to connect through our HTTP/HTTPs proxy farm, it usually fails. Specificially, I get the log-in page and can log in. It starts to render the landing page but redirects to a page stating "Your session has been terminated." On rare instances the first page will appear, however within a few clicks I end up with the same terminated page.
As a test, I bypassed the farm and forced my browser to use one proxy exclusively. At that point I could access the HTTPS interface with no issue. I have not had any issues with other SSL sites with the proxy configuration in use.Is there some sort of MITM prevention I could be running into? If so, can it be turned off.I am new to the RV-series of routers. Is there any logging I could turn on that would provide insight on why the session may be getting terminated?
View 2 Replies
View Related
Feb 11, 2012
I have 25 of these routers installed behind various providers and transport (DSL, Cable, UVerse). At sites where I have static IP, I can't reach any service inside, and in fact can't even reach the router for Remote Management. At all times the users indoes can do whtever they like, the have Internet access.
At sites where we draw a dynamic IP or use PPPoE, I can reach services and manage the router until a known issue stops the inbound traffic.
View 3 Replies
View Related
Jun 27, 2012
I have configured a VPN tunnel between two remote locations using static IP addresses on two RV042 routers. The tunnel seems to work but the problem is that when the two hosts attempt to ping each other only one can successfully ping. One PC with IP address 192.168.1.100 can ping across the network but the second PC with IP address 192.168.2.100 cannot. These are laptops seperate from the intranet used to test the tunnel. Someone had suggested NAT may be the issue so I enabled NAT Transverse on the routers but still no luck. The following is the results from a ping test.
PC 1
ping 192.168.2.1
Pinging 192.168.2.1 with 32 bytes of data:
Reply from 192.168.2.1: bytes=32 time=116ms TTL=63
[Code] ......
View 1 Replies
View Related
Feb 27, 2013
I recently replaced a Netgear router with a RV042 because I figured out my Netgear was choking my 24MB Uverse connection down to about 6MB. I had VPN setup with my business partner who was already using an RV042 and everyting works fine. However after I setup the RV042 on my side we have not been able to get the VPN up. The settings are as follows
Local Group
Local Security Gateway Type: IP Only
Local Security Group Type : Subnet
IP Address: 192.168.0.0
Subnet: 255.255.255.0
Remote Group
Remote Security Gateway Type: IP Only
remote Security Group Type : Subnet
IP Address: 10.0.0.0
[Code]....
View 1 Replies
View Related
Mar 1, 2013
I have the router for over two years, Present Firmware is V2.0.1.3, I have Polycom phone connected to the router using 8 x 8 VOIP service. The phone was working fine untill yesterday. 8 x 8 tech support suggested getting a different router. I have the same router at home and tried the same phone on my home router - it worked. So, the problem is not the phone but int he router. I tried to call Cisco tech support but found out that the warranty support expired and I need to buy a support plan. Called to buy the support, and gave up after an hours on hold. Left message.
View 1 Replies
View Related
Dec 20, 2010
My Linksys WRP400 router has stopped working. power led blinks red and orange - phone led 1 and 2 light green - wifi connection not work - ethernet LAN connection not work - ethernet WAN connection not work - router now work in bridge mode - factory reset using Reset switch not work - connected analogue phone not work I try dump traffic using ngrep on LAN and WAN port but no packet comes from the router.
View 2 Replies
View Related
Oct 12, 2011
I have a RVS4000 hardware v2 with firmware 2.0.2.7. I have a DSL modem in bridge mode and have the router set to PPPoE. Everything works fine except I want to use QOS which doesn't work fine. I have some vonage boxes set up on a switch set to port 1 trust mode is set to port and level 4 for highest priority. Port 2 I have on another switch set to priority 3. I tried turning bandwidth mangement on which doesn't seem to work at all so I don't even know if they QOS is even working. I set the max down stream and upstream provided after running a number of speed tests and setting it a little lower than my worst speed results. Once I did that I set up a rule for all traffic for rate control and set them just below the min and max I put in for isp bandwidth. I set the ip range from 192.168.1.100-190 this will cover anything that dhcp hands out and I also have a few statics set up on 192.168.1.180 and 181. However after enabling it I ran some speed tests and I still get full speed and the rules seem to be getting ignored.
View 2 Replies
View Related
Dec 8, 2011
I tried to configure two RV042 working together. [code] WAN2 of both Router1 and Router2 are unused (unplugged). However, the Host2 can never ping to Host1. So as to Host1. Should I need to configure the protocol binding for all the traffic to the WAN1?
View 3 Replies
View Related
Oct 21, 2011
So have a RV042 VPN router that is directly connected to the ethernet port of our comcast cable modem.
If I connect to it using QuickVPN (1.4.2.1) from a PC that is connected using AT&T 3G Network it works fine!
If I connect to it using QuickVPN (1.4.2.1) from a different PC that is connected using home WiFi (linksys wrtxxx) then it fails. In the VPN log all I see is failure messages for ping.
2011/10/22 15:47:28 [WARNING]Failed to ping remote VPN Router!
If I open a regular command prompt and attempt to ping the VPN router it works so not understanding why the QuickVPN is unable to ping.
how I can troubleshoot this further. Makes me think the RV042 config is fine otherwise it would not work on a 3G connection. Something on the home PC or the home network. Not sure what to check.
View 2 Replies
View Related
Jun 21, 2012
Updated to newest firmware 4.2.1.02 and wanted to perform a backup of the startup configuration. I get a "The webpage cannot be found" HTTP 400 error when trying to do this backup. I have changed some settings since my last backup, but that backup was done using the last firmware revision.
View 3 Replies
View Related
Apr 16, 2012
I have set up an RV042 v1 and v3 both in Load Balancing mode. Set in Router mode.I want one of the WAN ports to be preferred so I added a static route to 0.0.0.0 metric 5 to that WAN.Sometimes the route shows in the routing table and sometimes it goes away!!
View 2 Replies
View Related
Apr 1, 2012
When my RV042 is accessed for long transmissions (svn check out, usually after 20 minutes ) the client receives a message "Gateway not responding, do you want to wait".
When this happens I see the following in the RV042 system log (the first 3 lines of the log below are normal):
Apr 2 17:36:53 2012Connection AcceptedTCP 192.168.2.2:8888->192.168.1.5:50046 on ppp1Apr 2 17:36:54 2012Connection AcceptedTCP 192.168.2.2:8888->192.168.1.5:50046 on ppp1Apr 2 17:36:54 2012Connection
[Code]....
View 10 Replies
View Related
Aug 12, 2011
We bought an RV042 at the end of June. It is used as a gateway and VPN router. DHCP server is disabled and all IPs are configured manually.Every once in a while (Tuesday night, then Friday night - yesterday, it has hapened once or twice before that) the router appears to restart (see log below) then comes back up with system time of Jan 01 2010. At this point the router will no longer load its configuration page (https://10.29.238.197:16443/) and VPN connection to our customer in Africa drops. However, devices behind the router can be reached and can access the internet. The only way to fix this is to power cycle the router at which point everything starts working flawlessly again.The PID VID is RV042 V03 running firmware v4.0.3.03-tm (May 12 2011 21:27:37). Our RV042 is a newer one with Cisco SMB Router branding not the older Linksys branding.
From the log when the router reboots:
Aug 12 22:38:42 2011VPN Log(g2gips0) #141: retransmitting in response to duplicate packet; already STATE_QUICK_I2Jan 1 01:00:05 2010System Logheart : System is upJan 1 01:00:13 2010System LogWAN connection is up : 10.29.238.197/255.255.255.192 gw 10.29.238.225 on eth1Jan 1 01:00:15 2010VPN Log(g2gips0) #1: [Tunnel Negotiation Info] >>> Initiator Send Main Mode 1st packet
I looked at the log more and all the usual messages assosciated with VPN being established are there - the last thing in the log before the router coming back up again is:
Jan 1 01:03:49 2010VPN Log(g2gips0) #4: [Tunnel Negotiation Info] Quick Mode Phase 2 SA Established, IPSec Tunnel ConnectedJan 1 01:03:49 2010VPN Log(g2gips0) #4: [Tunnel Negotiation Info] Quick Mode Phase 2 SA Established, IPSec Tunnel ConnectedJan 1 01:03:49 2010VPN Log(g2gips0) #4: sent QI2, IPsec SA established {ESP=>0x575a01c0 <0x6534ae4e
So it even claims the tunnel should be up but I can never reach anything on the far side.
View 3 Replies
View Related
Feb 8, 2012
We have an RV042 on firmware version 1.3.13.02 and 2 ISPs:
WAN1 = Telepacific T1
1.5Mbps down and 1.5Mbps up
WAN2 = AT&T U-Verse
12Mbps down and 5Mbps up
I have it set to Load Balance, Primary WAN = WAN2
Network Service Detection enabled, only pinging the Remote Host of 4.2.2.2 and set to Generate Log
Bandwidth is set to:
WAN1 = 1000Kbps upstream & downstream
WAN2 = 5040Kbps upstream & 12000Kbps downstream
It seems to pick WAN1 a lot of the time. Do I have something setup wrong?
View 12 Replies
View Related
Dec 1, 2012
This is the RVS 4000
Firmware version 1.3.3.5
STAR 9202 Chipset
64 MB DRAM
8MB Flash
DOS, Block WAN Rq, Remote mgmt all OFF
IPSec Tunnel none used
[code].....
Every day or so the Router becomes unresponsive to the HTTP mgmt interface, as well as it no longer offers DHCP services.then this happens the only remedy is to power reboot.
Everything comes back online just fine, however, the LOGS are initilaized so no data to figure out what`s going on.My next step is to setuo a syslog server and have the logs copied out.( No, I have no Torrents running at all, but I do have several devices like AppleTV, PS3s etc that run streaming Video plus I have the SPA3102 )
View 1 Replies
View Related
Dec 23, 2011
I have my RV042 set up in Dual WAN mode and both WANs are working properly. I would like to configure WAN1 to handle all traffic, unless it fails and then have everything to go to WAN2. Pretty much what Smart Link Backup does, however with that enabled only 1 of the WANs is live at any given time. I'd like both WANs to always be live as I'm going to see the second one as a back-door into the network. Is this possible to do with routing? I tried setting a routing rule to have everything to go WAN1, but when WAN1 goes down, nothing is rounted via WAN2.
View 0 Replies
View Related
Nov 11, 2010
Any working configuration to connect the iPad VPN-client (IPSEC) to the RV042?
View 16 Replies
View Related
Jun 4, 2013
I have a RV042 router on a single WAN and an internal LAN. I have configured port forwarding as follows: HTTP[TCP/80~80]->10.0.0.6HTTPS[TCP/443~443]->10.0.0.6IMAP[TCP/143~143]->10.0.0.5IMAP SSL[TCP/993~993]->10.0.0.5SMTP SSL[TCP/587~587]->10.0.0.5
Everything works just fine when I have the firewall DISABLED. However, when I enable it the behaviour is erratic. 1 out of 10 attempts to connect to ANY port forwarded works. Almost all attempts time out. Notice that this happens even if using only the default firewall rules (which should be bypassed by the port forwarding as I read in other posts).
My second try was to create firewall rules manually, overriding the default ones. I tried adding rules from source WAN1 (where my connection is) to ANY and to SINGLE IP's on every port. Nothing seems to work.
I don't know what I'm doing wrong, this is really bugging me. I had to turn the firewall off so we can access our servers from outside the office. This shouldn't have to be done.
Just found out that my firewall is getting LOTS and LOTS of Blocked - SYN Flood entries. I think this is why we are having trouble with the firewall. Could this be the problem? I have no idea where all these SYN packets are coming from since they appear with spoofed IPs or come from different bots all over.
View 1 Replies
View Related
Oct 26, 2011
RV220W is at firmware v1.0.2.4 From: Administration / Management Interface / Web Accesss I have configured remote Management: Remote Management [x] EnabledAccess Type: All IP addressesPort Number: 8888Remote SNTP [ ] not enabled
From within the LAN side I can connect to the router and administer via https://192.168.3.97:8888
Status / System Summary reports:WAN (Internet) Information (IP4)
Connection Type: Static
Connection State: Connected
IP Address: 207.180.139.242
NAT: Enabled
But from the WAN side (using the same Win7 computer) I cannot connect via: https://207.180.139.242:8888
This used to work. Also not working: PPTP logins. ISP is RCN via cable modem, fixed IPs.
Have tried power cycling router - no luck. Have tried from PC with AV off and Win7 firewall off
View 5 Replies
View Related
