Cisco Routers :: RV042 Set Up In Dual Mode And Both WANs Are Working Properly
Dec 23, 2011
I have my RV042 set up in Dual WAN mode and both WANs are working properly. I would like to configure WAN1 to handle all traffic, unless it fails and then have everything to go to WAN2. Pretty much what Smart Link Backup does, however with that enabled only 1 of the WANs is live at any given time. I'd like both WANs to always be live as I'm going to see the second one as a back-door into the network. Is this possible to do with routing? I tried setting a routing rule to have everything to go WAN1, but when WAN1 goes down, nothing is rounted via WAN2.
View 0 Replies
ADVERTISEMENT
Nov 27, 2011
I have had the Netgear 3300 Dual Band for three years. Everytime I wanted to access using my laptop, I had to choose between 2.4G and 5G connection. For about a month now, the 5G does not show up. It doesn't show up as a network to select no matter what device I use. I have reset the router and updated the firmware. Both connection lights are blinking. I recently purchased and IPhone 4 and still I do not have the option of selecting 5G.
View 4 Replies
View Related
Feb 21, 2013
I run 2 RV042 V1 for home and office with Gateway to Gateway VPN connection with single WAN connection in use. Everything works like a charm!
I was even able to create VPN connection with 2 WAN connection on one Router and 1 WAN connection on another with Smart link failover and VPN Tunel Backup.
I got problem though when i tried more complex connection diagram. [URL]
So basically I now have 2 ISP connections on each point with Static IPs and I'd like VPN Connection to be alive for ALL 4 options automatically with failovers (smart links) And tunel backups but i'm not sure if that's ever possible with my equipment.
View 2 Replies
View Related
Feb 7, 2011
I've purchased a Linksys RV042 hoping I could connect my two ISP.Both of them are 1/1 Mb, first is DSL second PPPoE connection.The problem is that on system summary page it doesn't show me that second WAN is connected. Even when I trying to manually connect to Internet it doesn't work.
When this connection is in Load balance Mode, internet is very slow, sometimes it's even disconnected.
My question is:How to configure Load Balance properly?I've tried this page:
[URL]...
View 13 Replies
View Related
May 4, 2010
I have a multi-wan connections to RV016. WAN1 is T1 and WAN2 is DSL. There are some websites that I am having a problem logging in and staying logged in. It seems like the connection from my computer is going out through two different WANs.
How should I set my RV016 properly so that I won't have the above issues anymore?
View 1 Replies
View Related
Dec 10, 2012
2 router to connect my phone system to a Sip trunk provider router and to extend my Lan segments so the phone system have internet access.i need it this way because i cant put 2 default gateway in my phone system so the cisco Rv042 is the default gateway of the phone system and i use port fowarding of the UDP ports 5060 to point to the system.and i also use protocol binding of these ports to the Wan 1
Phone system connect to a switchport The sip trunk router connect to the Wan 1 My lan is connected to the Wan 2 Everything is working fine exept this intermittent issue : Each hour or so my sip trunk stop working. to make it start working i need to unplug my Wan 2 connection and wait for 1 minute.
View 4 Replies
View Related
Feb 26, 2012
ive been having some issues with my internet, i had an attack on my pc recently by some american orginization, ive reinstalled new windows on my pc, reset my modem, and nothign seems to work, i have too many tunnel adapters in cmd ip config i think, bell canada hooked up my internet lines and they actually joined two or more wires together and strung them up on the neighbours fence and mine and even wrapped it around a tree branch, god knows why they would even do that, maybe they think when the tree grows it will cost me money to fix it and theyll earn from thier mistakes instead of learn from them... anyway this is my ipconfig test results as explained in previous post from someone.Windows IP Configuration[CODE]
View 1 Replies
View Related
Aug 19, 2011
I need configuring Cisco RV042 dual wlan and port forwarding for 2 servers web and dns in LAN
View 1 Replies
View Related
Jan 7, 2013
I'm in the process of finding a dual WAN router with VPN support, that allow me to redirect some traffic to one specific WAN port and do load balancing of that specific traffic in case of that WAN failing (this last requirement is preferably but isn't fully needed).
Does the RV042/G could work with that? In that case, does it allow protocol redirect only? What about ip/ports redirecting? Or some kind of packet filtering to redirect to specific WAN ports?
View 6 Replies
View Related
Apr 22, 2013
Cisco RV042 Dual WAN VPN Router -how to configure dynamic DNS without having to use the pre-programmed DDNS companies that are populated by default if my DDNS company is not listed and you cannot manually enter another company that is not on the list?
View 1 Replies
View Related
Sep 19, 2012
I have an RV042 (it's old, silver/dark grey plastic front one) w/ firmware 1.3.13.02-tm.
The reason we bought this (long ago) was to balance two WAN connections, one with unlimited data and one capped monthly. It did that once, but for a couple years both connections have been unmetered so it's just been balancing them 50/50. As of today one WAN connection (the new much faster one) is back to being metered but I can't figure out how to configure the RV042 as it once was to prefer sending traffic over the slow, unmetered connection first, and only use the faster metered connection when necessary.
It's been a long time and honestly I only vaguely remember the ability to prioritize a connection based on % of bandwidth used so that all traffic would go over the unlimited connection 1st until it was flooded, and only then fall over to the metered connection. This is totally different than the weighted round robin, or smart link backup.
I found this 3rdparty forum post that supports that vauge memory and suggests this was eliminated between firmware 1.23 and 1.3: [URL] Is it possible to replicate this functionality with the current firmware? if so how? If not, how to do roll back to firmware 1.23?
It sounded like perhaps I could assigned WAN1 a bandwidth of 100000 (even though it's really 1500) and then assign WAN2 a bandwidth of 1 (even though it's really 20000) and the result might be the prioritization I'm looking to achieve... but I feel like I'm stumbling in the dark at the point.
View 1 Replies
View Related
Sep 5, 2011
I have 11 available IPs at a data center and have 5 servers I want configure - each with its own LAN, not to be networked together (used for web, ftp, sql and other webs services). Is it possible to configure the RV016 with 5 WANS, each attached to a specific port with its own LAN?
Am this even the right considerations for this router as I would just have normally purchased 5 routers and attached them individually to each server with their own specific WAN and LAN?
View 2 Replies
View Related
Apr 12, 2011
Is there any good description how to configure Linksys RV016 for two WANs (cable+DSL)? It looks like switching between those two connections not splitting what is set for WAN1 and what is set for WAN2. I set load balancing as- WAN1 (cable) all HTTP up/donw should go there- WAN2 (DSL) GTalk, IMs, SMTP, POP3, IMAP up/down should go therebut looks like is not working that way. When I will go to speedtest.net and test a connection I always get less amount then connected directly through cable : Also when people try to use any session or IP sensitive web site it doesn't let them to log in because session was expired (based on IP) or IP was changed.
View 11 Replies
View Related
Jan 6, 2012
I've had 1 to 1 NAT setup for years now with no issues and the other day it simply stopped working. Rebooted everything, had ISP clear arp on their cable modem yet nothing going. As soon as I remove the 1 to 1 NAT on the router the PC has internet access. Add the 1 to 1 back and no out going internet. The configuration is pretty basic and has not changed.Thinking it could be a hardware issue I swapped it out with another RV042 I have with the exact config, same thing 1 to 1 NATs have no internet access. Upgraded one of the RV042 firmware to Firmware Version: 1.3.13.02-tm, had cable modem replaced, spent numerous calls with ISP. nada
I have found one interesting thing however, any internal machine which is set to dhp works fine, and static ip that does not have a 1 to 1 nat works fine and the last ip in the 1 to 1 nat range works fine. If I extend the range it is always only the last ip that works. Even if I add 1 to 1 nats one line at a time, it is always the last entry that works..
View 4 Replies
View Related
Dec 8, 2011
I tried to configure two RV042 working together. [code] WAN2 of both Router1 and Router2 are unused (unplugged). However, the Host2 can never ping to Host1. So as to Host1. Should I need to configure the protocol binding for all the traffic to the WAN1?
View 3 Replies
View Related
Oct 21, 2011
So have a RV042 VPN router that is directly connected to the ethernet port of our comcast cable modem.
If I connect to it using QuickVPN (1.4.2.1) from a PC that is connected using AT&T 3G Network it works fine!
If I connect to it using QuickVPN (1.4.2.1) from a different PC that is connected using home WiFi (linksys wrtxxx) then it fails. In the VPN log all I see is failure messages for ping.
2011/10/22 15:47:28 [WARNING]Failed to ping remote VPN Router!
If I open a regular command prompt and attempt to ping the VPN router it works so not understanding why the QuickVPN is unable to ping.
how I can troubleshoot this further. Makes me think the RV042 config is fine otherwise it would not work on a 3G connection. Something on the home PC or the home network. Not sure what to check.
View 2 Replies
View Related
Jun 21, 2012
Updated to newest firmware 4.2.1.02 and wanted to perform a backup of the startup configuration. I get a "The webpage cannot be found" HTTP 400 error when trying to do this backup. I have changed some settings since my last backup, but that backup was done using the last firmware revision.
View 3 Replies
View Related
Apr 16, 2012
I have set up an RV042 v1 and v3 both in Load Balancing mode. Set in Router mode.I want one of the WAN ports to be preferred so I added a static route to 0.0.0.0 metric 5 to that WAN.Sometimes the route shows in the routing table and sometimes it goes away!!
View 2 Replies
View Related
Apr 1, 2012
When my RV042 is accessed for long transmissions (svn check out, usually after 20 minutes ) the client receives a message "Gateway not responding, do you want to wait".
When this happens I see the following in the RV042 system log (the first 3 lines of the log below are normal):
Apr 2 17:36:53 2012Connection AcceptedTCP 192.168.2.2:8888->192.168.1.5:50046 on ppp1Apr 2 17:36:54 2012Connection AcceptedTCP 192.168.2.2:8888->192.168.1.5:50046 on ppp1Apr 2 17:36:54 2012Connection
[Code]....
View 10 Replies
View Related
Aug 12, 2011
We bought an RV042 at the end of June. It is used as a gateway and VPN router. DHCP server is disabled and all IPs are configured manually.Every once in a while (Tuesday night, then Friday night - yesterday, it has hapened once or twice before that) the router appears to restart (see log below) then comes back up with system time of Jan 01 2010. At this point the router will no longer load its configuration page (https://10.29.238.197:16443/) and VPN connection to our customer in Africa drops. However, devices behind the router can be reached and can access the internet. The only way to fix this is to power cycle the router at which point everything starts working flawlessly again.The PID VID is RV042 V03 running firmware v4.0.3.03-tm (May 12 2011 21:27:37). Our RV042 is a newer one with Cisco SMB Router branding not the older Linksys branding.
From the log when the router reboots:
Aug 12 22:38:42 2011VPN Log(g2gips0) #141: retransmitting in response to duplicate packet; already STATE_QUICK_I2Jan 1 01:00:05 2010System Logheart : System is upJan 1 01:00:13 2010System LogWAN connection is up : 10.29.238.197/255.255.255.192 gw 10.29.238.225 on eth1Jan 1 01:00:15 2010VPN Log(g2gips0) #1: [Tunnel Negotiation Info] >>> Initiator Send Main Mode 1st packet
I looked at the log more and all the usual messages assosciated with VPN being established are there - the last thing in the log before the router coming back up again is:
Jan 1 01:03:49 2010VPN Log(g2gips0) #4: [Tunnel Negotiation Info] Quick Mode Phase 2 SA Established, IPSec Tunnel ConnectedJan 1 01:03:49 2010VPN Log(g2gips0) #4: [Tunnel Negotiation Info] Quick Mode Phase 2 SA Established, IPSec Tunnel ConnectedJan 1 01:03:49 2010VPN Log(g2gips0) #4: sent QI2, IPsec SA established {ESP=>0x575a01c0 <0x6534ae4e
So it even claims the tunnel should be up but I can never reach anything on the far side.
View 3 Replies
View Related
May 16, 2012
My organization has deployed 3 Cisco RV042 (v3) at our 3 sites. They have been working pretty well up until about a week ago. One of them continues to route traffic and perform port-forwarding, but the VPN has completely stopped working and I can no longer access the web administration interface. I get the standard login page, but any attempt to login (with correct or incorrect password) takes maybe 5 minutes with a spinning status icon, followed by a blank page leaving the browser at: url...
I have the router logs e-mailed to me, and I can see that the system boots up with Jan 1 2010 as the system date, but it eventually gets the correct date from NTP, so I'm doubting this is causing the problem.
These were working for months prior to this happening, and even a reboot of the affected RV042 does not allow me to log into it or setup the VPN tunnels. I have found similar threads on this forum: url...
View 2 Replies
View Related
Feb 8, 2012
We have an RV042 on firmware version 1.3.13.02 and 2 ISPs:
WAN1 = Telepacific T1
1.5Mbps down and 1.5Mbps up
WAN2 = AT&T U-Verse
12Mbps down and 5Mbps up
I have it set to Load Balance, Primary WAN = WAN2
Network Service Detection enabled, only pinging the Remote Host of 4.2.2.2 and set to Generate Log
Bandwidth is set to:
WAN1 = 1000Kbps upstream & downstream
WAN2 = 5040Kbps upstream & 12000Kbps downstream
It seems to pick WAN1 a lot of the time. Do I have something setup wrong?
View 12 Replies
View Related
Nov 11, 2010
Any working configuration to connect the iPad VPN-client (IPSEC) to the RV042?
View 16 Replies
View Related
Sep 30, 2012
I have a 6 month old RV042 with the newest firmware (v4.2.1.02). Over the weekend I configured the DMZ which after a lot of trial and error, was able to get working. Prior to configuring DMZ, I was able to log in with remote management. However now remote management no longer works. I've tried:
- Rebooting the router
- Turning the firewall off/on
- Turning remote management off/on
- Changing the remote management port
The only step I haven't taken is resetting the router back to factory defaults and trying to reconfigure it all again. This router is so finicky I have no faith I'd be able to get my current functionality back again.
View 2 Replies
View Related
May 22, 2012
The current setup we have contains two seperate networks, each managed by their own Cisco RV042 (10/100 4-Port VPN Router), and each have their own connection to a Comcast Business Class SMC Modem. (Each has its own static WAN IP provided by Comcast). Both VPN routers have VPN access configured allowing us to connect to our company's corporate intranet and network, and vice versa. Just as a reference point, We will call the first VPN 'GamesNetwork' and the other one 'AdminNetwork'. A problem came up where the computers on AdminNetwork could not access the resources of the GamesNetwork. The problem was resolved by our at-the-time official corporate IT guy but the solution was never explained to me. Recently i got curious and went into the config pages and found that each VPN router was linked to the other the same way corporate links to our VPN's, whch is by using the Internet IP of that vpn... So to me this says we are linking two local vpn networks using their internet connection which is on the same modem.. to me this seems messed up. is this really the way it needs to be done? Now... I have thought of the idea 'make the two networks into 1..' and it could work. but.. i dont have the permission to make this happen.
if you have two vpn routers side by side in the same room, is there a more local means of giving 1 vpn access to the resources of the other and vice versa?
View 1 Replies
View Related
Jun 4, 2013
I have a RV042 router on a single WAN and an internal LAN. I have configured port forwarding as follows: HTTP[TCP/80~80]->10.0.0.6HTTPS[TCP/443~443]->10.0.0.6IMAP[TCP/143~143]->10.0.0.5IMAP SSL[TCP/993~993]->10.0.0.5SMTP SSL[TCP/587~587]->10.0.0.5
Everything works just fine when I have the firewall DISABLED. However, when I enable it the behaviour is erratic. 1 out of 10 attempts to connect to ANY port forwarded works. Almost all attempts time out. Notice that this happens even if using only the default firewall rules (which should be bypassed by the port forwarding as I read in other posts).
My second try was to create firewall rules manually, overriding the default ones. I tried adding rules from source WAN1 (where my connection is) to ANY and to SINGLE IP's on every port. Nothing seems to work.
I don't know what I'm doing wrong, this is really bugging me. I had to turn the firewall off so we can access our servers from outside the office. This shouldn't have to be done.
Just found out that my firewall is getting LOTS and LOTS of Blocked - SYN Flood entries. I think this is why we are having trouble with the firewall. Could this be the problem? I have no idea where all these SYN packets are coming from since they appear with spoofed IPs or come from different bots all over.
View 1 Replies
View Related
Aug 4, 2012
Just finished building my new computer yesterday - i installed windows 7 and all the motherboard drivers etc - everything went smoothly. I then plugged in my ethernet cable but saw that in normal mode my computer had very slow internet. I went into safe mode with networking and tried the internet there and it was its normal speed. Obviously something is booting up in normal mode that is stopping/limiting the connection. I uninstalled norton (came with the motherboard drivers) using the uninstall norton tool, i also uninstalled any other virus protection and disabled my computers firewall but to no avail - it's still real slow.
View 3 Replies
View Related
Jul 25, 2011
First of all i have gateway 2 gateway VPN configuration (both same RV042 with same firmware) + QVNP clients
The first one that i have those lines in my log "Ignoring Vendor ID payload" which doesn't allow clients to be connected from the first time they connect after several retries, or can't connect at all. I've doublechecked ports opened, and 500 is blocked by ISP. Also double checked, tried turning on and of Windows machine firewalls and etc - nothing worked. What would be the solution? should i manage to call my ISP and ask opening the port and it will solve my problem? HTTPS is enabled on router (this one i read in other topic)
The other problem is that one of my routers just stuck and i have manually to turn off, and then to turn on that it would start working as it was. Log files doesn't show anything. Router started to crash after the last Firmware upgrade.
View 1 Replies
View Related
Oct 24, 2011
I'm a bit new at this and I wanted to know if this is possible with the RV042 or if there's a better product to use. Our server is at located at location A and locations B and C telnet to the server via a VPN. We're looking at getting another ISP at each location as a backup and abandon older modem backups.
Would I setup a VPN tunnel between (A and B) and (A and C) for each ISP? Also I had a question on local IP addresses and if this would work
location A, ISP 1 -> location B, ISP1
local IP 192.168.1.1 remote IP 192.168.2.1
Public IP aa.aa.aa.aa Public IP bb.bb.bb.bb
[ code]....
View 2 Replies
View Related
Mar 29, 2012
I wanted to ask a question about the diagram I have included. We are bringing up 2 MPLS WAN connections and would like some specifics on the best design. We are using BGP to the providers. From there we have big questions. We can run BGP internal and are licensed to do so on the N5K's. The N5Ks are currently using HSRP for inside LAN clients as default gateway. We want to load balance and provide redundant routes using a dynamic approach. Should we use BGP internal utilizing the connections between the routers? Should we use HSRP on the routers? How best to get the routes to the N5K and should we be considering this?
View 5 Replies
View Related
Jun 3, 2012
Im having a problem with my wireless. My whole family is connented. to wireless. But when we all use it together it goes so slow. Like 4 some times only 2 people using it at the same time.
View 9 Replies
View Related
Nov 30, 2011
I have a an issue with one particular VPN user. They are using the built in Windows Vista client to connect to my ASA 5510.
All other users do not have an issue and i receive the following error at roughly the same time of day when the drop happens. Authentication is done by my AD Server which handles all logins.
[code]...
View 2 Replies
View Related
Feb 27, 2012
I not familiar with the ASA 5510 product. I having trouble since last 24 hours and still cant find out the root cause yet. Here is my scenario, my network should be
WAN --- ASA5510 (FW) --- SERVER (192.168.1.0/24)
Now I face the problem, all the NAT static 1-to-1 is working OK. All my public IP can be ping from outside internet. But the problem happen when I try to telnet to port 80 on each server. I had try telnet from my PC to public IP 124.xxx.179 80, it's work fine, but failed on 124.xxx.180 80, then on 124.xxx.181 80, its work fine.
Then I do try on my colleague PC, in same network as mine, I face another case where the public IP 124.xxx.179 80 cannot be telnet, but it's ok for 124.xxx.180, then failed on 124.xxx.181 80.
FYI.. all our PC can ping to the Public IP and no packet lose.
The scenario is very weird, I cant find any other solution as had review my configuration few times.
check does my configuration is working perfectly or not.
ASA Version 8.2(5)
!
hostname fw-asa
enable password xxx encrypted
[Code].....
View 8 Replies
View Related
