Cisco RV042 Dual WAN VPN Router -how to configure dynamic DNS without having to use the pre-programmed DDNS companies that are populated by default if my DDNS company is not listed and you cannot manually enter another company that is not on the list?
View 1 RepliesI need configuring Cisco RV042 dual wlan and port forwarding for 2 servers web and dns in LAN
View 1 Replies View RelatedI run 2 RV042 V1 for home and office with Gateway to Gateway VPN connection with single WAN connection in use. Everything works like a charm!
I was even able to create VPN connection with 2 WAN connection on one Router and 1 WAN connection on another with Smart link failover and VPN Tunel Backup.
I got problem though when i tried more complex connection diagram. [URL]
So basically I now have 2 ISP connections on each point with Static IPs and I'd like VPN Connection to be alive for ALL 4 options automatically with failovers (smart links) And tunel backups but i'm not sure if that's ever possible with my equipment.
I'm in the process of finding a dual WAN router with VPN support, that allow me to redirect some traffic to one specific WAN port and do load balancing of that specific traffic in case of that WAN failing (this last requirement is preferably but isn't fully needed).
Does the RV042/G could work with that? In that case, does it allow protocol redirect only? What about ip/ports redirecting? Or some kind of packet filtering to redirect to specific WAN ports?
I purchased 2 RV042's (h/w version 3) less than two months ago. I updated them to the latest firmware (v4.0.4.02-tm (Jul 4 2011 13:30:56)), did a factory reset to make sure I was working with a clean slate, set up DDNS through DynDNS and a site to site VPN between the two. Everything was working great for a month, then the DynDNS accounts expired because they weren't being updated. I reactivated the names on the DynDNS site, and started to monitor the "last updated" date and time. After 24 hours there were no updates according to the DynDNS site. I logged into one of the RV042's, and it said "Dyndns Enabled : Dynamic DNS is updated successfully." This is a stale message from 24 hours ago when I hit save. So I went into Setup | Dynamic DNS | Edit Config and there it also says "Dynamic DNS is updated successfully." I clicked "Save", status changed to " Dyndns Enabled : Updating..." for a few seconds, and then back to "Dyndns Enabled : Dynamic DNS is updated successfully". I refreshed the DynDNS website and it shows the current time (in eastern time, i'm pacfic) as the last time it was updated. So it works when I manually hit the "Save" button. Not making any changed, just hitting "Save". I've let the other RV042 go over 48 hours and it still hasn't updated. So it apears for the time being, I'll have to remember to push the "Save" button once a week to prevent my DynDNS accout from expiring. Does DDNS working in the lastest firmware and h/w version 3? If so, what is the update frequency?
View 6 Replies View Related2 router to connect my phone system to a Sip trunk provider router and to extend my Lan segments so the phone system have internet access.i need it this way because i cant put 2 default gateway in my phone system so the cisco Rv042 is the default gateway of the phone system and i use port fowarding of the UDP ports 5060 to point to the system.and i also use protocol binding of these ports to the Wan 1
Phone system connect to a switchport The sip trunk router connect to the Wan 1 My lan is connected to the Wan 2 Everything is working fine exept this intermittent issue : Each hour or so my sip trunk stop working. to make it start working i need to unplug my Wan 2 connection and wait for 1 minute.
I have my RV042 set up in Dual WAN mode and both WANs are working properly. I would like to configure WAN1 to handle all traffic, unless it fails and then have everything to go to WAN2. Pretty much what Smart Link Backup does, however with that enabled only 1 of the WANs is live at any given time. I'd like both WANs to always be live as I'm going to see the second one as a back-door into the network. Is this possible to do with routing? I tried setting a routing rule to have everything to go WAN1, but when WAN1 goes down, nothing is rounted via WAN2.
View 0 Replies View RelatedI have an RV042 (it's old, silver/dark grey plastic front one) w/ firmware 1.3.13.02-tm.
The reason we bought this (long ago) was to balance two WAN connections, one with unlimited data and one capped monthly. It did that once, but for a couple years both connections have been unmetered so it's just been balancing them 50/50. As of today one WAN connection (the new much faster one) is back to being metered but I can't figure out how to configure the RV042 as it once was to prefer sending traffic over the slow, unmetered connection first, and only use the faster metered connection when necessary.
It's been a long time and honestly I only vaguely remember the ability to prioritize a connection based on % of bandwidth used so that all traffic would go over the unlimited connection 1st until it was flooded, and only then fall over to the metered connection. This is totally different than the weighted round robin, or smart link backup.
I found this 3rdparty forum post that supports that vauge memory and suggests this was eliminated between firmware 1.23 and 1.3: [URL] Is it possible to replicate this functionality with the current firmware? if so how? If not, how to do roll back to firmware 1.23?
It sounded like perhaps I could assigned WAN1 a bandwidth of 100000 (even though it's really 1500) and then assign WAN2 a bandwidth of 1 (even though it's really 20000) and the result might be the prioritization I'm looking to achieve... but I feel like I'm stumbling in the dark at the point.
I recently bought two RV042s to create a site to site VPN for a client. I have several of these setups installed at other locations but this is the first version 3 hardware I've used.It seems like the dynamic IP functionality of the VPN setup may not be working correctly. I've verified all settings on each router match and have deleted/recreated the setup several times just to make sure. Here's the logs from the router with a static IP.
Nov 29 06:49:51 2012 VPN Log (g2gips0): deleting connection
Nov 29 06:49:51 2012 VPN Log added connection description (g2gips0)
Nov 29 06:49:51 2012 VPN Log listening for IKE messages
Nov 29 06:49:51 2012 VPN Log forgetting secrets
Nov 29 06:49:51 2012 VPN Log loading secrets from '/etc/ipsec.d/ipsec.secrets'
Nov 29 06:49:51 2012 VPN Log (g2gips0): cannot initiate connection without knowing peer IP address
Nov 29 06:49:51 2012 VPN Log (g2gips0): cannot initiate connection without knowing peer IP address
I've tried both dynamic IP + email and dynamic IP + FQDN to authenticate the router using the dynamic IP and both give the same error as above.I did a firmware update hoping to fix PPPoE which seemed to be broken with a Netopia modem in bridge mode so both routers are on the latest firmware, v4.2.1.02.
I tried to configure two RV042 working together. [code] WAN2 of both Router1 and Router2 are unused (unplugged). However, the Host2 can never ping to Host1. So as to Host1. Should I need to configure the protocol binding for all the traffic to the WAN1?
View 3 Replies View RelatedI have a RV042 VPN Router with the latest firmware v4.2.1.02.This Router is connected to the main site by a VPN Tunnel.
Now, I like to configure some DHCP Option so I can put a IP Phone behind the RV042. The IP Phone should receive a IP by DHCP from the RV042 and of course, the IP of the Call Manager with the Option 150.
I can configure DHCP and it works fine but I can't find where I have or can configure Option 150.
We have a RV082 configured with two ISP Wan connections. We recently implemented a VOIP phone system (SIP) (192.168.1.50) that is being used in appliance mode on our network. We currently have two WAN connections Load Balanced. My goal is to configure all my VOIP traffic to go out through the 1st ISP and the rest of the data through ISP #2. is this possible to achieve using the RV082? We are using a Skype SIP Trunk connection.
View 1 Replies View RelatedI've purchased a Linksys RV042 hoping I could connect my two ISP.Both of them are 1/1 Mb, first is DSL second PPPoE connection.The problem is that on system summary page it doesn't show me that second WAN is connected. Even when I trying to manually connect to Internet it doesn't work.
When this connection is in Load balance Mode, internet is very slow, sometimes it's even disconnected.
My question is:How to configure Load Balance properly?I've tried this page:
[URL]...
I have tried replacing a loaner RV082 V2 with an RV042 V3 router with firmware 4.0.4.02. All worked well, including the site to site VPN. However, in spite of the fact that I have ports 443 and 4125 forwarded to the server (192.168.2.10), we are unable to connect via RWW. There is no such problem with the RV082. What is different with the way we configure these V3 routers for port forwarding?
View 2 Replies View RelatedI have an Internet link, connected to my Cisco Router. The package I subscribed for comes with a dynamic IP Address. I was told, if I need to remote access into the Cisco Router, I need to enable the DDNS feature. Can this be done on a Cisco Router?
View 1 Replies View Relatedhow to configure the Cisco 1941 router for PPPOE with dynamic IP
View 10 Replies View RelatedHaving a problem everytime I try to use load balance on my Rv042 it is slow as a dog and sometimes wont connect at all. if I run in smart backup mode its fine. removed firewall rebooted everything tried numerous configerations upgraded to the latest frimware just about to be convinced
View 2 Replies View RelatedSo far I have a complete phase 1, and an almost complete phase 2, but one thing I can't figure out. I see this in the debug. peer is not authenticated by xauth - drop connection.
I get it right after the proxy is setup.
Here is my config
group-policy DefaultRAGroup attributes
vpn-idle-timeout none
vpn-tunnel-protocol ikev1 l2tp-ipsec
[Code]....
I have tried many different configurations on both sides, but they all fail with the same error of peer not authenticated by xauth.
I need to configure an existing 2600 router to use dynamic NAT for access to the web and ALSO I have (5) fixed IP addresses for use with an email server, a web server, and (3) future servers. I do not know the concept of how to set this up. I'm currently using dynamic NAT for the web and this seems OK but I dont know how to map my fixed servers. I assume this is done with static NAT. Do I need to add sub interfaces on the S0/0 T1 interface for each of these fixed IPs? Then do I somehow do static NAT on these fixed IPs to their respective servers?
View 14 Replies View RelatedI have a site with an ASA5505 and 2 isp connections but the catch is the 2 isp's are giving me a dynamic IP so I am unable to use this [URL]
View 3 Replies View RelatedIs there a way to set up a Site-to-site VPN between RV042 & Cisco 2911? I "googled" this and obtained a document, but it is not regarding Cisco 2911: [URL]
Routers are needed to setup it successfully. I have tried on both routers several configuration steps, no success...
I've 3 interfaces on router:
Gb0/0-ISP01 with DHCP client
Gb0/1-ISP02 Static IP 192.168.2.x/24
Fa0/0 - LAN 192.168.1.1/24
I want to know, how to configure:1. Set the IP of interface Gb0/0 as dhcp client from ISP01 and make it as default route.
2. How to configure the ip nat.....overload?
3. How to use the ip sla to monitor internet connectivity to 8.8.8.8 for ISP01, if it fails, to go to ISP02.
I'm wondering if there is a possibility to get my homepage provider's custom dynamic DNS service working on my Cisco SRP541W Router as I'd not like to be forced to sign up for either DynDNS or TZO which are available through the web frontend.
View 1 Replies View RelatedFirst of all i have gateway 2 gateway VPN configuration (both same RV042 with same firmware) + QVNP clients
The first one that i have those lines in my log "Ignoring Vendor ID payload" which doesn't allow clients to be connected from the first time they connect after several retries, or can't connect at all. I've doublechecked ports opened, and 500 is blocked by ISP. Also double checked, tried turning on and of Windows machine firewalls and etc - nothing worked. What would be the solution? should i manage to call my ISP and ask opening the port and it will solve my problem? HTTPS is enabled on router (this one i read in other topic)
The other problem is that one of my routers just stuck and i have manually to turn off, and then to turn on that it would start working as it was. Log files doesn't show anything. Router started to crash after the last Firmware upgrade.
I'm a bit new at this and I wanted to know if this is possible with the RV042 or if there's a better product to use. Our server is at located at location A and locations B and C telnet to the server via a VPN. We're looking at getting another ISP at each location as a backup and abandon older modem backups.
Would I setup a VPN tunnel between (A and B) and (A and C) for each ISP? Also I had a question on local IP addresses and if this would work
location A, ISP 1 -> location B, ISP1
local IP 192.168.1.1 remote IP 192.168.2.1
Public IP aa.aa.aa.aa Public IP bb.bb.bb.bb
[ code]....
how i can configure the Cisco RV042 to access PPTP VPN Server (Witopia VPn) or other vpn servers.
View 1 Replies View RelatedI have configured a cisco router 877 to run the Dynamic DSL. However, it cannot work, the ATM 0 interface cannot be up . Here is my configuration:
version 12.4
no service pad
service timestamps debug datetime localtime
service timestamps log datetime localtime
no service password-encryption
[code]....
I wanted to ask a question about the diagram I have included. We are bringing up 2 MPLS WAN connections and would like some specifics on the best design. We are using BGP to the providers. From there we have big questions. We can run BGP internal and are licensed to do so on the N5K's. The N5Ks are currently using HSRP for inside LAN clients as default gateway. We want to load balance and provide redundant routes using a dynamic approach. Should we use BGP internal utilizing the connections between the routers? Should we use HSRP on the routers? How best to get the routes to the N5K and should we be considering this?
View 5 Replies View RelatedHow config dynamic alp inspection for 300 or 500 series ? I find in admin guide it's no simple to do.
View 8 Replies View RelatedBasically I have an internet router (1841ISR) with 1 internal (LAN) connection and 2 internet connections. What I want to do is route specific traffic for 3 of my internally hosted services (smtp, https, etc) through one internet connection (fa0/0) and then route all other traffic through the unmanaged/dynamic IP ADSL connection (Dialer 0).
View 9 Replies View RelatedI have a Linksys RV042 10/100 4-Port VPN Router with Firmware Version 1.3.13.02 and l have noticed that the Router keeps rebooting on average every couple of hours.We have it setup for Load Balancing 2 ADSL Services.
View 3 Replies View RelatedI have been able to put two Linksys routers in series no problem but this doesn't seem to work with an RV042.I have a number of customers that need to connect to a private email network via a router based VPN, but since VPN traffic is not filtered in the firewall, I would like to use an older Linksys router to manage the VPN(s) and have it pass data in through the filters of an RV042 on the DMZ port.I am getting stuck on the very frist part of this. Although I can connect to both the RV042 and LinkSys directly (by adjusting my subnet), I cannot ping the Linksys when it is connected through the DMZ port even if I disable the RV042 Internet port.
I know both the Internet and DMZ ports work on the RV042. I suspected that perhaps the RV won't pass through private IPs and tried known available pubic IPs instead of the 192.168.2.x subnet, but still no ping.What would be limiting the RV in this case? Is is possible to setup the RV to work in series with another router? Is there any other way to filter VPN traffic?
Using these routers for VoIP phones, the manufacturer says that SIP ALG must be disabled. I cannot find a setting for this.
View 1 Replies View Related