I have a Linksys RV042 10/100 4-Port VPN Router with Firmware Version 1.3.13.02 and l have noticed that the Router keeps rebooting on average every couple of hours.We have it setup for Load Balancing 2 ADSL Services.
View 3 RepliesI've got a WRVS4400N V2 Router that just keeps rebooting itself. It powers up, the red LED stays lit, it gets part way through the boot process and reboots itself. I would like to try to re flash the device, but don't know if this is possible in the condition that it is in.
View 3 Replies View RelatedI have an N750 DB router and it has been rebooting every few hours for no reason. This has just started happening about 4 days ago. I don't know why but when I check the system logs its filled with the following. [code]
View 2 Replies View RelatedI've got a RV220W that for some reason has started acting a bit strange. A couple of times a day the network stops functioning, both wireless and wired. At first I thought this had to do with my newly installed laptop, that it maybe caused some hickup that made the router reboot but even when it's turned off I can still read in the logs of my NAS server (Qnap TS-419P+) that "Lan 1 is down" followed by a "Lan 1 is up" a couple of minutes after.
The things connected to the network by wire is my Macbook Pro (2012), the Qnap and an LG home theater system and the wireless devices are a couple of iPhones and an iPad. The problems started after new years eve and I've been running the latest firmware (1.0.4.17) for a few weeks before that.
How do I stop the rv220w from continuously rebooting?
I have been keeping track of when it crashes and reboots and here is what has happened today:
14/03/2013 00:26 crashes and reboots
14/03/2013 07:28 crashes and reboots
14/03/2013 11:14 crashes and reboots
[Code]....
our RV220W router has been experiencing random reboots throughout the day, causing a network outage for our local network for the few minutes it takes for the router to start up again. We've seen it reboot at least 5 today alone (and the time is currently just a little over 1pm).I'm having trouble finding the reason for these reboots in the router's logs, although I find these two lines repeating in the error log:
Mon Jan 28 13:20:52 2013(GMT+0100) [rv220w][System][EVTDSPTCH] umiIoctl (18, UMI_CMD_DB_UPDATE(4)) failed. table=dot11STA row=11
Mon Jan 28 13:20:52 2013(GMT+0100) [rv220w][System][PLATFORM] /pfrm2.0/bin/bwLimitConfig /tmp/system.db 18 dot11STA 11 failed. status=-1
I'm not sure why these messages pop up, since we're not using the bandwidth limiter module of the router (granted, we do use QoS profiles to ensure our own LAN is prioritized over the guest VLAN). I'm also not sure whether this is related to the router reboots.
I also find the following repeated line in the warning log:
Mon Jan 28 12:50:50 2013(GMT+0100) [rv220w][Kernel][KERNEL] ERROR:endChantRecv: protocol PNAC returned !OK
The router is currently running on firmware version 1.0.4.17 (latest official release), since we needed support for hairpin connections (as I found out in a previous thread of mine). I've seen the suggestion of downgrading to a previous firmware version in another thread, which has possibly solved it for the poster in that thread, but as we really need the hairpinning support, I don't know which firmware version is safe enough to downgrade it to, if needed.
I have a persistent any very annoying issue that the router reboots on it's own when I am streaming video from Netflix or other similar applications.
I read some reviews about this router which stated that this was a known problem, but apparently was resolved with latest firmware updates.
My router is new (less than 1 year). It came originally with the 2.0.1.2 firmware which I updated to the 2.0.1.3
That did not resolve the problem. So my question is, is there any aditional configuration necessary to stream video without interruptions, or, is this a hardware problem?
I have an RV016 V3 with firmware 4.2.1.02 that is constantly rebooting making it unusable. I have one LAN connect and 3 WAN's, 2 DSL's and one Cable Internet in a load balance config. I have tried firmware 4.2.1.01 and it reboots also. do I get and RMA from Linksys and send this pig back?
View 6 Replies View RelatedI have a RV120W that reboots itself when the WAN (ADSL modem) breaks away. With an old D-Link low end router, reconnecting after a failure is completed after 5 seconds and nobody cares, but the RV rebooting takes almost 2 minutes which is actually noticed...I also have some trouble getting VPN running, QuickVPN as well as normal IPsec, using either Shrewsoft or Greenbow as clients. get this router running with 3rd party VPN clients?
View 1 Replies View RelatedI have a RV220W setup with SSL VPN users, authenticating to an internal Active Directory. Maybe 5 ports forwarded and 8 external IP addresses. Besides this i have 1 data VLAN and a voice vlan on my network.
The reboots are on different times on a day, even on Sundays at 7 AM when noone is logged in to the network.FW is at 1.0.4.17.
Why My Belkin Router F5D8236-4 Ver 2 always rebooting itself. the router lamp is on and then the security lamp is on and then the router rebooting itself. this happening because im push the reset button. im already try to upgrade the firmware with recovering tool (Boot Loader / Tiny Kernel Version v0.02) from 192.168.2.1 but the problem still happening.
View 3 Replies View RelatedMy RV110W is only a few months old and apparently started ginvg me issues shortly after I got it. Since it was new, however, I only recently suspected it as the culprit!
I have a simple home/small business setup. A single PC wired into the lan and a handful of occasional use laptops & Android phones/tablets and a Playstation.My connection is a 30M down / 5M up cable link. I have a UBEE DOCSYS 3.0 cable modem operating in passthru mode to my RV110W.
Over the course of several days, thruput drops from the measured 30/5 down to as low as 1/whatever. Rebooting the RV110W restored full speed. The UBEE has never been rebooted during this time. Connecting my wired desktop PC directly to the UBEE modem give me the full 30 downlink speed even when the RV110W perfomance has dropped to 5 or even 1.
I am using onle a single wireless LAN, no logging turned on, no VPN, no other 'tuning of settings.As it is, this device must be rebooted every few days to restore full network speed. This is unacceptable, of course - especially from a small business class device!
I have been able to put two Linksys routers in series no problem but this doesn't seem to work with an RV042.I have a number of customers that need to connect to a private email network via a router based VPN, but since VPN traffic is not filtered in the firewall, I would like to use an older Linksys router to manage the VPN(s) and have it pass data in through the filters of an RV042 on the DMZ port.I am getting stuck on the very frist part of this. Although I can connect to both the RV042 and LinkSys directly (by adjusting my subnet), I cannot ping the Linksys when it is connected through the DMZ port even if I disable the RV042 Internet port.
I know both the Internet and DMZ ports work on the RV042. I suspected that perhaps the RV won't pass through private IPs and tried known available pubic IPs instead of the 192.168.2.x subnet, but still no ping.What would be limiting the RV in this case? Is is possible to setup the RV to work in series with another router? Is there any other way to filter VPN traffic?
Using these routers for VoIP phones, the manufacturer says that SIP ALG must be disabled. I cannot find a setting for this.
View 1 Replies View RelatedWhat is the WAN to LAN Throughput of RV042 router with QoS and SPI enable?
Will the RV042 router able to support a 60Mbps down 3Mbps up Internet connection with QoS enable and SPI enable without slowing down the connection?
Just installed RV042 router. And it's giving out router certificate instead of server certificate so people who are trying to access our secured server are getting errors. I'm not talking about remote management. I'm talking about people trying to access our web site, which is secured, and getting an error because the RV042 is giving its own SSL certificate instead of the Server's certificate. How do we turn that off or keep it from happenning?
The RV042 firm version is v4.0.0.07-tm (Aug 19 2010 19:19:50)
I'm in the process of finding a dual WAN router with VPN support, that allow me to redirect some traffic to one specific WAN port and do load balancing of that specific traffic in case of that WAN failing (this last requirement is preferably but isn't fully needed).
Does the RV042/G could work with that? In that case, does it allow protocol redirect only? What about ip/ports redirecting? Or some kind of packet filtering to redirect to specific WAN ports?
We have a CISCO RV042. We are about to begin a VIOP service with Vocalocity who state:
The RV042 is a wired router that requires no configuration adjustments for the firmware versions we tested. Version 1 and 2 are compatible. Version 3 is NOT. Firmware Reviewed: 1.3.12.6 | 1.3.12.19
Our router's firmware is : 1.3.8.2 (Feb 12 2007 10:43:08)
Can we upgrade to 1.3.12.6 or 1.3.12.19? What is meant by Version 1, 2 and 3?
Cisco RV042 Dual WAN VPN Router -how to configure dynamic DNS without having to use the pre-programmed DDNS companies that are populated by default if my DDNS company is not listed and you cannot manually enter another company that is not on the list?
View 1 Replies View RelatedI am setting up remote access using an RV042 router. Using quickvpn or a client-to gateway vpn and shrewsoft client, I can only access/ping the LAN side of the remote router and one machine on the remote network. The PPTP server and native Windows 7 connection provide access to all machines on the remote network.I have 2 possible reasons for this and would like to find the real reason:
1) The remote RV042 is behind another router, and that router restricts access other than the PPTP traffic.
2) The VPN tunnels other than PPTP only allow access to the remote LAN side of the router and remote machines that have the remote router defined as their gateway in the IP configuration.
I am using an RV042 router/firewall -- firmware v1.3.13.02-tm -- connected to a cable modem.I have one public address (WAN1) assigned by my ISP's DHCP server.All my machines on the LAN have static IPs. (RV042 DHCP Server is disabled.)I have set up port (80) forwarding to 192.168.1.101 The HTTP port forwarding does work if an http client on the LAN sends a request to http://<public-ip>:80But I cannot get a response if I send a request to http://<public-ip>:80 from a machine on the WAN.
I did configure Access Rules to allow http traffic (and then tried to allow *all* traffic) between a single IP on the WAN and 192.168.1.101 The incoming log table shows a connection is made from the http client on the internet to the correct http server on the LAN, but there is no resonse from the LAN to the remote client.Is my configuration the problem, or is this feature not supported by the RV042 router? Could my cable modem be blocking outbound traffic?
I have RV042 and E4200 routers . I tried the manual UPnP port forwarding using Rv042 router and was succesful ( by typing 192.168.1.1 in the explorer and logged in using user name and password )
I am using a linux embedded system whose Internal IP ,Internal port are mapped .This system is connected to one of the LAN ports
I want to try auto UPnP port forwarding both for RV042 router and Linksys E4200 routers
After enabling the Upnp option only and logging out ,Can i add a port mapping entry in this router without logging in using a C++ program which runs on linux embedded system .
I was looking for a small business router that has VPN support and dual WAN support for load balancing. Upon reading reviews, I think RV042/RV042G is a good choice. Now am thinking if it supports intervlan/ router-on-a-stick configuration?
View 5 Replies View RelatedI have 3845 Router which is continuously rebooting; console output is attached.
View 8 Replies View RelatedI just got a DIR-655, and I got it working, with some effort. However, the wifi stops connecting to the internet every few hours and requires a reboot. Only a reboot of the wifi portion of the router's software, I go to Manual Wireless Connection Setup and save it without changing anything. LAN connections don't experience this.
Comcast Cable connection
DIR-655
Hardware Version: B1
Firmware Version: 2.00NA
I am 17 routers Cisco 837 With Cisco IOS Software, C837 Software (C837-K9O3SY6-M), Version 12.3(2)XE4, RELEASE SOFTWARE (fc1)
My tunnel is mounted but falls after 1 day.is there a way to automate the recovery of the tunnel without rebooting the router !
[code]...
Recieved this E4200 as a repplacement for a v1 that kept dropping wireless connection. Now after about 1.5 months the router keeps rebooting. Tried resetting, etc...no luck. Calling Cisco now.
View 3 Replies View RelatedRegion : Others
Model : TL-MR3040
Hardware Version : V2
Firmware Version : 3.14.4. Build 121017 Rel 62268n
ISP : CellC
I bought the MR3040 to use only with battery but now my if used with 3G stick E1752 it reboots. If I use a powered hub then it works.
I thought this devive was a mobile device, now it seems I need external power.
I recently formatted the flash drive of an 1800 router and replaced it with an updated image. However, the new features within the new image aren't reflected in the router. I believe that this is because a reboot would be required for the updates in the new image to be reflected in the router i.e. the image needs to be added to the system. How to get the image to the system without a reboot and if by doing so I would get all the new features from the image.For example, the show version below shows the old image in the system as [code]
View 2 Replies View RelatedI might have to reboot my operating system, I have a Cisco wireless router, so I have to reset it, and set it up again after i reboot my operating system?
View 8 Replies View RelatedI recently updated the firmware to 1.0.02 on my E4200 and since then it's been rebooting randomly about once a day. It was working perfectly fine before the firmware update.
View 5 Replies View RelatedI have a problem with my EA4500. Router permanently rebooting. - router is not visible on the network. Ping to 192.168.1.1 - loss of all packets; - hard reset (30/30/30) does not work.
View 9 Replies View RelatedI just bought an EA-4500 and i am having problems with rebooting the device. Every time I change a setting and the router reboots it never starts up again - and the logo LED doesn't flash, it is on constant. I have to cut the power and wait for about 15 minutes, and then it boots up fine - logo flashing and all.
View 5 Replies View Related