Cisco Routers :: RV220W Rebooting At Random Intervals?
Jan 27, 2013
our RV220W router has been experiencing random reboots throughout the day, causing a network outage for our local network for the few minutes it takes for the router to start up again. We've seen it reboot at least 5 today alone (and the time is currently just a little over 1pm).I'm having trouble finding the reason for these reboots in the router's logs, although I find these two lines repeating in the error log:
Mon Jan 28 13:20:52 2013(GMT+0100) [rv220w][System][EVTDSPTCH] umiIoctl (18, UMI_CMD_DB_UPDATE(4)) failed. table=dot11STA row=11
Mon Jan 28 13:20:52 2013(GMT+0100) [rv220w][System][PLATFORM] /pfrm2.0/bin/bwLimitConfig /tmp/system.db 18 dot11STA 11 failed. status=-1
I'm not sure why these messages pop up, since we're not using the bandwidth limiter module of the router (granted, we do use QoS profiles to ensure our own LAN is prioritized over the guest VLAN). I'm also not sure whether this is related to the router reboots.
I also find the following repeated line in the warning log:
Mon Jan 28 12:50:50 2013(GMT+0100) [rv220w][Kernel][KERNEL] ERROR:endChantRecv: protocol PNAC returned !OK
The router is currently running on firmware version 1.0.4.17 (latest official release), since we needed support for hairpin connections (as I found out in a previous thread of mine). I've seen the suggestion of downgrading to a previous firmware version in another thread, which has possibly solved it for the poster in that thread, but as we really need the hairpinning support, I don't know which firmware version is safe enough to downgrade it to, if needed.
View 10 Replies
ADVERTISEMENT
Jan 18, 2013
I've got a RV220W that for some reason has started acting a bit strange. A couple of times a day the network stops functioning, both wireless and wired. At first I thought this had to do with my newly installed laptop, that it maybe caused some hickup that made the router reboot but even when it's turned off I can still read in the logs of my NAS server (Qnap TS-419P+) that "Lan 1 is down" followed by a "Lan 1 is up" a couple of minutes after.
The things connected to the network by wire is my Macbook Pro (2012), the Qnap and an LG home theater system and the wireless devices are a couple of iPhones and an iPad. The problems started after new years eve and I've been running the latest firmware (1.0.4.17) for a few weeks before that.
View 1 Replies
View Related
Mar 14, 2013
How do I stop the rv220w from continuously rebooting?
I have been keeping track of when it crashes and reboots and here is what has happened today:
14/03/2013 00:26 crashes and reboots
14/03/2013 07:28 crashes and reboots
14/03/2013 11:14 crashes and reboots
[Code]....
View 1 Replies
View Related
Dec 3, 2012
I have a RV220W setup with SSL VPN users, authenticating to an internal Active Directory. Maybe 5 ports forwarded and 8 external IP addresses. Besides this i have 1 data VLAN and a voice vlan on my network.
The reboots are on different times on a day, even on Sundays at 7 AM when noone is logged in to the network.FW is at 1.0.4.17.
View 1 Replies
View Related
Mar 26, 2011
My internet is randomly disconnecting every once in a while. It seems to be at random intervals of 30 minutes to two hours. While it is disconnected my modem lights are still on and it says that I am connected to the internet.I am wired directly to a modem from my computer.
View 4 Replies
View Related
May 30, 2012
I have a simple ASA, ACS, AD schema for RA VPN authentication. All is working for a few months now, but since the initial deployment we have this connectivty issue regarding ACS and MS AD. At random intervals, 1 month/1 week, the ACS connection status becomes "DISCONNECTED" although the CLI shows that ad client is running. But because of that, no RA VPNs can be authenticated. Clock is not a problem, since it didn't change automatically nor was manually configured prior to the malfunction.
View 2 Replies
View Related
Jan 18, 2012
I have a WBR-1310 router that for the past few weeks has been giving me 'limited access' issues at psuedo-random intervals. The router functioned perfectly for a long time, I dug it out of storage about 8 months ago, and up until Christmas it was working fine, then both my roommate and I got tablets. Now our router is supporting 6 devices (PS3, 360, lappy, 2 tablets, smartphone) and occasionally more (other peoples phones, roommates laptop once he gets it repaired). However my research online has led me to believe that I should be able to support near unlimited wireless devices on the network (though effectively only around 30). Still, these extra two tablets are the ONLY change to the network that happened immediatly prior to this problem starting.Now I find that when I'm home alone I can go for the whole day with no network issues, but as soon as my roomy gets home and starts to use his devices the network craps out. unplugging the router and modem for 30 seconds fixes the problem temporarily, though the time before it craps out again ranges from hours to minutes.
I CAN plug my lappy into the modem directly when the router is not functioning and still have internet access, so it's definitely the router with the issue.All devices except for the PS3 are using wireless. I've done a hard reset to the router and set it back to factory settings on two occasions, I've changed the SSID and passphrase to get others off the network, I've changed the security type twice, I've tried some suggestions for similiar problems online such as enabling 'gaming mode' on my routers homepage, and setting a custom IP address (I used 10.0.0.1).Over the last 72 hours or so (the problem has existed for a few weeks) I've also received a few messages about my laptop having an IP address conflict; unsure if that is related, but I'm still able to access the internet when I get that message (albeit slower than average) [code] I will update this with another ipconfig the next time my internet dies; which I'm sure will be sometime today.
View 3 Replies
View Related
Feb 11, 2013
Wired PC randomly disconnects from network at random intervals each dayoday it has done so 3 times. The only way I have found to get it working again is to reset the router which can be inconvenient. When it disconnects all wireless devices continue to work and I have no issues like this with my wired consolesI switched to using a static IP address, since having an automatic one gave me the same results [i have since switched back to automatic]Be happy for any suggestions on how to sort this. I am using W7 OS and I'm using an Orange router. I don't know if its relevant, but when I go to reset my router I have noticed that the download light on my router is flashing like crazy when my PC has disconnected.
View 7 Replies
View Related
Jan 26, 2011
I've been having this problem on my desktop and it's really annoying when i try to play online games that need a constant connection.I have Windows XP and i'm using a wireless connection via a wireless USB adapter. The problem is that the internet is running fine but at random intervals it starts to not send or receive any packets. This will usually cause my to disconnecting during a game causing other players inconvenience. After I d/c the internet will usually take 5-30 seconds to start sending and receiving packets again and regain connection.
View 14 Replies
View Related
Jun 29, 2012
Router is connected to my ISP with the option Keep alive and redial value of 20 seconds (the lowest i can set). There are two distinct problems: Router drops connections at random intervals. It can happen once a day or several times a day. It always happens overnight (so every morning it isn't connected). This doesn't seem to be related to ISP as direct connection to computer is stable.The Keep alive option isn't working. When it drops connection it isn't trying to re-eastablish it for at least 2 minutes (the longest i have waited so far, 6 times the redial value configured). Producing external traffic (e.g. constant pinging of some host by IP address, refreshing some web page) doesn't work. When i log on to admin console (browser based) simply clicking connect button brings connection back online. I've even been looking at status page constantly refreshing to see if it ever made a single attempt and it appears it didn't.I did my "homework" before posting (upgraded FW to 2.0.02 build 3, finetuned MTU).
View 2 Replies
View Related
Mar 21, 2012
I have a Linksys RV042 10/100 4-Port VPN Router with Firmware Version 1.3.13.02 and l have noticed that the Router keeps rebooting on average every couple of hours.We have it setup for Load Balancing 2 ADSL Services.
View 3 Replies
View Related
Nov 28, 2012
I've got a WRVS4400N V2 Router that just keeps rebooting itself. It powers up, the red LED stays lit, it gets part way through the boot process and reboots itself. I would like to try to re flash the device, but don't know if this is possible in the condition that it is in.
View 3 Replies
View Related
Aug 5, 2012
I have a persistent any very annoying issue that the router reboots on it's own when I am streaming video from Netflix or other similar applications.
I read some reviews about this router which stated that this was a known problem, but apparently was resolved with latest firmware updates.
My router is new (less than 1 year). It came originally with the 2.0.1.2 firmware which I updated to the 2.0.1.3
That did not resolve the problem. So my question is, is there any aditional configuration necessary to stream video without interruptions, or, is this a hardware problem?
View 2 Replies
View Related
Dec 6, 2012
I have an RV016 V3 with firmware 4.2.1.02 that is constantly rebooting making it unusable. I have one LAN connect and 3 WAN's, 2 DSL's and one Cable Internet in a load balance config. I have tried firmware 4.2.1.01 and it reboots also. do I get and RMA from Linksys and send this pig back?
View 6 Replies
View Related
Aug 16, 2011
I have a RV120W that reboots itself when the WAN (ADSL modem) breaks away. With an old D-Link low end router, reconnecting after a failure is completed after 5 seconds and nobody cares, but the RV rebooting takes almost 2 minutes which is actually noticed...I also have some trouble getting VPN running, QuickVPN as well as normal IPsec, using either Shrewsoft or Greenbow as clients. get this router running with 3rd party VPN clients?
View 1 Replies
View Related
Apr 22, 2013
Why My Belkin Router F5D8236-4 Ver 2 always rebooting itself. the router lamp is on and then the security lamp is on and then the router rebooting itself. this happening because im push the reset button. im already try to upgrade the firmware with recovering tool (Boot Loader / Tiny Kernel Version v0.02) from 192.168.2.1 but the problem still happening.
View 3 Replies
View Related
May 20, 2013
My RV110W is only a few months old and apparently started ginvg me issues shortly after I got it. Since it was new, however, I only recently suspected it as the culprit!
I have a simple home/small business setup. A single PC wired into the lan and a handful of occasional use laptops & Android phones/tablets and a Playstation.My connection is a 30M down / 5M up cable link. I have a UBEE DOCSYS 3.0 cable modem operating in passthru mode to my RV110W.
Over the course of several days, thruput drops from the measured 30/5 down to as low as 1/whatever. Rebooting the RV110W restored full speed. The UBEE has never been rebooted during this time. Connecting my wired desktop PC directly to the UBEE modem give me the full 30 downlink speed even when the RV110W perfomance has dropped to 5 or even 1.
I am using onle a single wireless LAN, no logging turned on, no VPN, no other 'tuning of settings.As it is, this device must be rebooted every few days to restore full network speed. This is unacceptable, of course - especially from a small business class device!
View 6 Replies
View Related
Nov 29, 2012
I have an N750 DB router and it has been rebooting every few hours for no reason. This has just started happening about 4 days ago. I don't know why but when I check the system logs its filled with the following. [code]
View 2 Replies
View Related
Dec 29, 2012
Network running about 60 computers, most of which are running windows 7 professional. Some are on a domain, some are not.At (seemingly) random times, some computer on the network will lose the ability to browse websites (including the web interfaces of networked devices). I can't identify what circumstances cause this to occur. I only find out about it when someone calls me.From the affected computer:I can ping sites I can ping our Cyberoam UTM (which acts as our DNS, DHCP, and firewall)disabling/enabling connection doesn't fix the problem releasing/renewing ip doesn't fix the problem flushing dns doesnt fix the problem uninstalled antivirus on two test machines, problem still randomly manifests.replaced the Cyberoam with newer model users have claimed that if they wait a long period of time (40+ minutes) the problem sometimes resolves.rebooting the computer resolves the issue until it randomly occurs again changing the computer's mac address also resolves the issue until it randomly occurs again.
View 3 Replies
View Related
Apr 2, 2012
what exactly is QuickVPN?Is it a IPSec VPN?Is it a PPTP?Is it a SSLVPN?can I resolve my local hostnames? That means, can I configure a lokal DNS Server?
View 3 Replies
View Related
Aug 24, 2012
I am trying to setup and configure a VPN on the RV220W that uses IPSEC so I can use the Cisco VPN Client I use at work, I have gone through the user manual 11 or 12 times now but still cannot work it out. I cannot find where on the Rv200W iset up the phase 1 authentication username and password which will then lead me onto the phase 2 stage of asking for a username password to allow me access.
View 8 Replies
View Related
Jul 3, 2012
Picked up a pair of RV220W's for a project I'm working on. I have several IP's available, 4 of which are assigned to/in use by a server behind the RV220W. All 4 of these IP's are static external IPs. How I can configure the RV220W so that requests to those 4 IP's get routed to the server.
Prior to purchasing this, I was under the impression what I was trying to do was called one-to-one NAT, but after reading the 'Help' document on the one-to-one NAT page, I don't think this is right. Emphasis added below: Cisco RV220W Wireless-N Network Security Firewall Help FirewallOne-to-One NATOne-to-one NAT is a way to make systems behind a firewall and configured with private IP addresses appear to have public IP addresses.One-to-One-NAT Rule TableThis table lists the list of available One-To-One NAT rules configured by the user. Private Range Begin: start ip address in private (LAN) ip addressPublic Range Begin: start ip address in the public ip address (WAN IP), Public IP Subnet Mask: The Subnet Mask of the public IPRange Length: Range length maps one to one private address to public address up to the given range.Service: This column shows service to be accepted by LAN Host.The actions that can be taken on One-to-One-NAT rules are:(Check Box At First Column Header): Selects all the entries in the table.Add: Opens the One-To-One NAT Configuration page, to add a new entry. Edit: Opens the One-To-One NAT Configuration page, to edit the selected entry.Delete: Deletes the selected entries.
So according to their documentation, the server in question would need to be configured with a private IP. Unfortunately, one of the applications I use is licensed via IP address and my understanding is that I cannot use the software with private/non-routable IP addresses.
Is the RV220W capable of not only securing the line (firewall, access rules, content filtering, port trigering & forwarding etc) but also doing what I was hoping to do (keeping the external IP's on the server, and routing appropriately)?
View 9 Replies
View Related
May 15, 2012
I'm using a RV220W router, and recently got shifted to a dynamic IP solution.Now, I've got a no-ip.org address, but the update service seems to be on no-ip.com. So, I try to enter mydomain.no-ip.org OR mydomain.no-ip.com in the dynamic dns settings, under Host and Domain Name, but when saving the settings it says
'The hostname specified does not exist in this user account' ,which seems to indicate that it manages to login to the update service but gets a negative reply.Is it possible to use the RV220W with no-ip.org/com?
View 5 Replies
View Related
Dec 12, 2012
We have 2 sites connected thru 2 RV220W routers via VPN and most things are working fine. I have noticed however, that any device that has a web interface, i.e. our Sharp Copier and our Freenas server, is inaccessible. The page tries to come up but then I get the Cisco "server is down" page generated by the RV220W.
I can pull up the web interface pages if I use a machine on the local LAN but not on any machine across the VPN. The only commonality I can think of is the RV220W blocking that traffic for some reason..
View 8 Replies
View Related
Sep 28, 2011
Cisco support write down manual (workaround), how to setup IPsec VPN connection on Mac OS 1.7?
View 5 Replies
View Related
Nov 27, 2011
Is there anyway to associate a name to an IP in the RV220W? I am coming from a WRVS4400N v2. Folks are complaining that they can't connect, for example via Real VNC, via the PC name any longer. They have to use the IP address. In the past I put the names of the PCs in the WRVS4400N when I reserved IPs via MAC addresses (some call this assigning static IPs). There isn't any place in the RV220W to put the name. Even when I look at the DHCP list a lot of them show up as "unknown". I am sure this is a NETBIOS thing but I'd rather fix this in the router as I have always done in the past.
View 4 Replies
View Related
Jul 22, 2011
i have a RV220W and absolutely nothings functional on this stupid Router, no NAT , no Port Forwarding and I cant access my Network from Outside. Any firmware link for downloading. This address works, its handling special webrequest.
View 1 Replies
View Related
Jul 19, 2012
I set up a PPTP VPN with an RV220W recently. It was working flawlessly until a recent power outage and now users are getting the 807 error when attempting to connect. I have PPTP passthrough enabled and TCP/UDP 1723 open. As far as I can tell GRE 47 is open as well. Why it was working and is not working after a power outage?
View 2 Replies
View Related
Jun 23, 2012
Having a strange problem that just started this week and got worse this evening. I have a RV220W that is feeding my network. The RV220W sits behind a broadband modem and acts as the DHCP for the network and those computers access the internet that way. Anyway, tonight started an issue where the the RV220W just disappears. Becomes unpingable. I recycle power, and within anywhere from 5 to 10 minutes, it's gone. No longer pingable. Even if I plug a latop directly into it.If I power cycle the RV220W it comes back and I can ping it and access it and its settings. 5 to 10 mins later, I again lose it. Nothing was done. Its been working fine for a few weeks. Had a similar outage last Tuesday, but a recycle of everything brought everything back into line. After I lose connection to it, the lights I expect to be lit remain lit.
View 1 Replies
View Related
May 29, 2012
We are running WLAN using WPA2-enterprise with AES & IAS server.Mostly we are using AP's 1131 and Cisco WLC 4400.I added on a new location 2 AP 1142G and since the installation I got 3-4 clients having regular disconnections.Basically they are connected immediately to the infrastructure but after a certain amount of time the Win7 icon is having this yellow exclamation sign, and we can see that the connectivity is gone (however the IP settings seems to be still in place, but ping or network browsing is not possible).Stopping the WLAN and starting it again solve immediately the issue (via software or via the notebook switch). Normally the problem doesn't resolve by itself.
I was working beside the laptop having the problem with (my own laptop) during the person got 3 disconnections, mine was running like a charm.We have 85% of the people there working errors free.Checked the 1142 AP for any logs or errors, interfaces status etc...Checked the switches behind, interfaces seems running smoothlyChecked IAS / WLC / WCS for any logs that can indicate an issueCompared WLAN adapter settings of the faulty laptop with mine, discovered some differences and adapted it.Compare the WLAN SSID config in Win7 with mine and adapted the slighty differences found.Used WCS troubleshooting client tool.What I will do again :Verify if the persons having the issue have the same laptop modelVerify settings in the BIOS Verify WLAN adapter driver versionVerify BIOS versionUse WCS troubleshooting client tool on my own laptop at this place.
View 1 Replies
View Related
Aug 10, 2011
I have the Qwest/Actiontec Q1000 modem/router. I go to the ip address using my web-browser and open up advanced configurations -> access scheduler. I select a computer (and it automatically adds the MAC address) and then the days/times I want the internet to be accessible. However, when I click "add" (to add my internet allowance to the scheduler list) it just says 12:00 to 0:00, which is essentially permanently blocking the internet for that computer.
View 7 Replies
View Related
Jan 26, 2012
I am unable to make UPnP to work on the RV220W. I am forced to use port forwarding.
View 10 Replies
View Related
Nov 20, 2012
Nothing happens when clicking the SAVE button after making changes on the VLAN Membership screen when using IE9, but it work fine with IE8. Any problems using IE9 during configuration?
View 4 Replies
View Related
