Block Access To Internet On Specific Time Intervals?
Aug 10, 2011
I have the Qwest/Actiontec Q1000 modem/router. I go to the ip address using my web-browser and open up advanced configurations -> access scheduler. I select a computer (and it automatically adds the MAC address) and then the days/times I want the internet to be accessible. However, when I click "add" (to add my internet allowance to the scheduler list) it just says 12:00 to 0:00, which is essentially permanently blocking the internet for that computer.
View 7 Replies
ADVERTISEMENT
Jul 3, 2012
How to block a specific website with a specific time (office hours) for example "facebook" I want to block facebook within 8AM - 12Noon then 12-1 they can access the website, then 1-4 block again the website .
View 3 Replies
View Related
Feb 11, 2013
I have an 1841 between my firewall and the ISP. Three interfaces - multilink to ISP, FA to my firewall, and FA to my inside network. I use the inside interface for configs aand snmp access, etc. Only my ISP-assigned fixed address block will get routed to the multilink by the ISP but I am nervous about the inside interface sitting on my LAN. I know I can remove it, but if I keep it there, how can I set up an ACL so that all traffic from the multilink interface is denied to the inside interface? I suppose another way to think about it that the inbound iface can only accept traffic from its own outside, not from the router.I think this is fairly simple but I don't want to knock down the traffic if I get it wrong.
View 8 Replies
View Related
Jan 2, 2012
I want to block the sql port access of my server to all except few of my ip addresses while access list on Cisco Router IOS how do i do that.
View 3 Replies
View Related
Sep 20, 2012
With M10, I cannot restrict internet access for specific time period. Parent Control feature doesn't satisfy the situation, and there is no build-in access-policy in web-based setup. Are you going to upgrade firmware or Cisco Connect with more flexible access time control?
View 1 Replies
View Related
Sep 7, 2012
How to block Internet Connection during specific time.for example i want to block everyday between 8am to 12nn, then 1pm to 5pm.what are the options and better to achieve this kind of policy??
View 6 Replies
View Related
Jan 10, 2013
I am facing a proble in wireless connection speed that is getting very slow at a specific time, i.e., from 12pm to 2pm and from 9 pm to 2 am. The service is unlimitted type contract
View 1 Replies
View Related
Jan 18, 2012
I have a WBR-1310 router that for the past few weeks has been giving me 'limited access' issues at psuedo-random intervals. The router functioned perfectly for a long time, I dug it out of storage about 8 months ago, and up until Christmas it was working fine, then both my roommate and I got tablets. Now our router is supporting 6 devices (PS3, 360, lappy, 2 tablets, smartphone) and occasionally more (other peoples phones, roommates laptop once he gets it repaired). However my research online has led me to believe that I should be able to support near unlimited wireless devices on the network (though effectively only around 30). Still, these extra two tablets are the ONLY change to the network that happened immediatly prior to this problem starting.Now I find that when I'm home alone I can go for the whole day with no network issues, but as soon as my roomy gets home and starts to use his devices the network craps out. unplugging the router and modem for 30 seconds fixes the problem temporarily, though the time before it craps out again ranges from hours to minutes.
I CAN plug my lappy into the modem directly when the router is not functioning and still have internet access, so it's definitely the router with the issue.All devices except for the PS3 are using wireless. I've done a hard reset to the router and set it back to factory settings on two occasions, I've changed the SSID and passphrase to get others off the network, I've changed the security type twice, I've tried some suggestions for similiar problems online such as enabling 'gaming mode' on my routers homepage, and setting a custom IP address (I used 10.0.0.1).Over the last 72 hours or so (the problem has existed for a few weeks) I've also received a few messages about my laptop having an IP address conflict; unsure if that is related, but I'm still able to access the internet when I get that message (albeit slower than average) [code] I will update this with another ipconfig the next time my internet dies; which I'm sure will be sometime today.
View 3 Replies
View Related
Mar 26, 2011
My internet is randomly disconnecting every once in a while. It seems to be at random intervals of 30 minutes to two hours. While it is disconnected my modem lights are still on and it says that I am connected to the internet.I am wired directly to a modem from my computer.
View 4 Replies
View Related
Apr 5, 2011
How do I block specific domains (pandora.com, etc.) in the Sonicwall? It seems like this would happen in the CFS but do I need a subscription for this? I don't want to subscribe to Sonicwall's filtering list, I just want to block a couple specific domains.
View 9 Replies
View Related
Oct 31, 2011
I have a TL-WR740N Wireless Lite N Router and i want to block specific websites with it.
View 4 Replies
View Related
Oct 5, 2011
How to configure the 825 to block inbound traffic from a specific internet IP address ?i noticed an IP and MAC that i don't recognize that is listed as a connection to my NAS's media server ...i blocked it in the NAS configuration page, but i don't want any unsolicited traffic into my network.
View 3 Replies
View Related
Jan 26, 2011
I've been having this problem on my desktop and it's really annoying when i try to play online games that need a constant connection.I have Windows XP and i'm using a wireless connection via a wireless USB adapter. The problem is that the internet is running fine but at random intervals it starts to not send or receive any packets. This will usually cause my to disconnecting during a game causing other players inconvenience. After I d/c the internet will usually take 5-30 seconds to start sending and receiving packets again and regain connection.
View 14 Replies
View Related
Apr 4, 2012
I dont mean a website like facebook.com, but i want it to block an individual page,such as a profile page, yet still be able to access the rest of the site? Again i'm not after facebook settings etc, but i want to restrict access to certain webpages within Lan.
View 2 Replies
View Related
May 4, 2011
I have Cisco ASA 8.0(5) and I need to block specific url to acees my https server in dmz ?I read about websence technology, but I think it's not free right? Also I read abotu policy inspection map's but in my case is HTTPS not http ..
View 1 Replies
View Related
Nov 15, 2011
How does a firewall block or filter traffic on a specific port or IP address?
View 1 Replies
View Related
Jul 8, 2011
I have a WAG160Nv2 and I want to block specific external ip addresses from trying to get at our server that uses the WAG160Nv2 as an internet gateway. It's not immediately obvious if this can be done from looking through the config pages.
View 4 Replies
View Related
Jul 25, 2011
if the firewall rules in the RVL200 work for inter LAN routing as well as LAN<->WAN? I need 2 separate networks in a house, 1 for business 1 for family, and I want to only allow my IP on network 1 (family net,10.0.0.0/24) access to network 2 (business net 10.0.1.0/24). I want this as if I change rooms were a access point for business is not available I can use the home net and specific IP to access certain business net IPs. I saw you can turn inter vlan routing on or off, but it wasn't clear on firewall rules.know of a similar router in cost but with gige instead of 100Mb ports?
View 1 Replies
View Related
Apr 22, 2012
I'm using an ASA5505 (8.4(1)) and would like to block port 80 on a specific host in the LAN so machines in other remote LANs connected via VPN can't access this port on the host. Devices in the local LAN should have access to this port on the host. Here are the commands I'm using:
-access-list block_port extended deny tcp any host 10.20.10.20 eq 80
-access-list block_port extended permit ip any any
-access-group block_port out interface inside
These commands are not working as I would expect them to. When I browse to http://10.20.10.20 from a remote machine over the VPN tunnel I am able to access the host web server.
View 2 Replies
View Related
May 20, 2013
I have arequirement where in I need to allow only specific vendor made desktops/laptops to be connected to the switch and block the rest. Say I want only the HP made Laptops to be connected on the Network. and block all other vendors. such as dell, ibm etc.
I am having Catalyst 4500 switches in My network. i tried using the mac access list using the permit and deny statement and then mapping the access list to the vlan access map and then filter using the vlan id. But this doesnt work on cat 4500....the same I tested for 2950 switch and it works perfectly. are there any restrictions on 4500 or any extra configuration has to be done.
View 2 Replies
View Related
Mar 3, 2011
Using a DIR-655, does anybody know how to create a firewall rule to block all dns requests except to specific servers?
View 2 Replies
View Related
Dec 4, 2012
I was wondering if it was possible to block imessage to specific clients on the EA6500.These are the ips apple uses for imessage I need to create a firewall rule that blocks these ips from reaching a specific client on the network.
[code]....
View 1 Replies
View Related
Dec 17, 2012
I have a Belkin N750 router which I purchased because the box said it had filtering options. I didn't realize that the filtering was only sites that Norton kept track of. There are certain adware sites I know about that I would like to filter. Possible with this router?
View 5 Replies
View Related
Jan 8, 2012
I'm a college student working on a lab involving a Cisco PIX 501 Firewall.
My project involves 1 computer and a firewall. My goal is to use the firewall to allow access to the internet for that computer which uses a static IP 192.168.1.5 and ONLY for that IP address. The firewall is connected to the internet.
I have the computer hooked up to the firewall with the serial and using hyper terminal to enter commands. I think I need to use access lists in order to deny traffic on those ports for those particular hosts. I can't figure out exactly how I need to set it up.
What I need to do is permit internet access for 192.168.1.5 alone. Any other IP should not be able to access the internet.
I tried:
access-list 1 permit tcp host 192.168.1.5 any eq 80
access-group 1 in interface inside
I cannot access the internet using the computer with 192.168.1.5. The goal is to be able to access with that IP and no other.
View 6 Replies
View Related
May 21, 2012
I am setting up a network for a friend with children. He has a BT homehub and wants to block their access between certain hours. However by using access control on BT it tells you that you have been blocked which is no good as he cannot feign ignorance and pretend he doesn't know what to do (as his kids will pester him to fix it). He therefore wants to block their access more discreetly (as if the internet was generally timing out or messing up instead of actually displaying they have access control).Is there a way to block an individual's access on the router without blocking everybody either on a timer or manually done each time (thus if there isn't a way of automating it he can at least do this manually each time).
View 1 Replies
View Related
Mar 15, 2011
How do I configure Cisco ASA 5505 (using ASDM 5.2) to block a workstation (IP address) from accessing internet completely? I was trying to set up a new incoming access rule for outside interface to deny any IP traffic to that workstation but it doesn't work from some reason - the workstation can still access the internet. The ASA has no special settings, only a few ports opened for servers?
View 1 Replies
View Related
Sep 25, 2012
i saw on router address that someone is using my wifi and i just want to disconnect him without changing my wifi password
View 1 Replies
View Related
Jul 20, 2011
Lately I've been experiencing connection problems between my router and cable modem. Every night after 11:00 PM EST, my Internet connection sporadically goes out. I called my ISP who said there was nothing wrong on their end. Plugging directly into my modem allows me to access the Internet. When I wake up in the morning, the connection is back until 11 or later again. I ran WireShark but I'm not sure what to be looking for. There are a lot of random things from the LLMNR protocol like standard query A zmtvrjaql.
View 2 Replies
View Related
Apr 14, 2011
How can I block my son's computer from internet access through our wireless router without having his computer in hand? I have accessed the router on line but don't know what to change there.
[code]...
View 4 Replies
View Related
Nov 23, 2012
How to block internet access some of the computers in a network
View 2 Replies
View Related
Aug 27, 2011
How to block other persons getting in my internet services
View 3 Replies
View Related
Aug 22, 2011
I am trying to allow a block of 7 or 8 devices to access the internet all the time. Two other devices I would like to allow internet access during a set time range. Finally I would like to block internet access to all devices not in one of the above groups. I need to use MAC addressing to identify the allowed devices. I was able to do this with my old WRT-54G but the DIR-825 is giving me trouble.My main problem occurs when I try to block access to "Other Machines". When I do that all devices on my network are cut off the internet.
View 5 Replies
View Related
Apr 2, 2013
I have an EA4500. I am trying to block a specific site based on keywords in the webpage address. how to get the EA4500 to block sites with based on keywords.
View 1 Replies
View Related