I have a Belkin N750 router which I purchased because the box said it had filtering options. I didn't realize that the filtering was only sites that Norton kept track of. There are certain adware sites I know about that I would like to filter. Possible with this router?
I recently purchased an E-2500, but notice that in parental controls I can only block 6 or 8 websites. In my WRT54GS I could just create additional rules and they would work. But in this device I am limited on the sites that can be blocked per device. How I can block additional sites?
I dont mean a website like facebook.com, but i want it to block an individual page,such as a profile page, yet still be able to access the rest of the site? Again i'm not after facebook settings etc, but i want to restrict access to certain webpages within Lan.
I want to block sites like facebook during my workday but allow the rest of the internet.
The attached settings block facebook as desired during the filter times but after 6:30pm the filter expires and the entire internet is blocked (not just facebook). All of my browsers act as if they are hanging and won't load pages until I disable the filter.
I've also tried creating two different filters (one at a time). The first allowed full internet access all the time and the second allowed access the opposite times of the work filter. But to no avail.
if the firewall rules in the RVL200 work for inter LAN routing as well as LAN<->WAN? I need 2 separate networks in a house, 1 for business 1 for family, and I want to only allow my IP on network 1 (family net,10.0.0.0/24) access to network 2 (business net 10.0.1.0/24). I want this as if I change rooms were a access point for business is not available I can use the home net and specific IP to access certain business net IPs. I saw you can turn inter vlan routing on or off, but it wasn't clear on firewall rules.know of a similar router in cost but with gige instead of 100Mb ports?
How to block a specific website with a specific time (office hours) for example "facebook" I want to block facebook within 8AM - 12Noon then 12-1 they can access the website, then 1-4 block again the website .
I was wondering if it was possible to block imessage to specific clients on the EA6500.These are the ips apple uses for imessage I need to create a firewall rule that blocks these ips from reaching a specific client on the network.
how do I block IP/Internet Adresses for ALL users without adding the sites manually per user in the Parental Control panel? I want to block a certain IP/internet adress for all users but can't find this feature within my EA6500 anywhere?Is this a firmware bug? Has linskys forgotten that some sites want to blocked for all users and how do I do it all in one?
I'm trying to solve up a really nasty problem I have at home and I've come here hoping to find some answers. Since last Saturday, I am unable to access certain internet sites when at home. Strangely enough everything was fine before that. Went to bed around midnight local time and when I went to check those sites after work at around 3:30 pm local time I could not get on those sites. For some reason the pages just keep on endlessly loading, giving me only a blank page. What is also strange is that no computer in my house can access those sites. So it's not limited to one computer.
I need to block sites in my network. I tried Proxy but they are overcoming using the option auto detect proxy settings. How can i restrict the access only through the proxy, Do I have to do anything with DNS server?
I am trying to filter her website visits. I have a list of sites blocked at the router, but sometimes the ipod gets around this. I set the ipod to a static ip. Now is there anyway to block certian websites to this IP only?can't with laptop but can with the ipod via facebook. I thought I read someplace that you can block sites to a users static ip or mac address. I haven't been able to find it in my router settings. Im using a netgear wnr2000v3.
In my office there is 2 desktops which is networked. one is in the office and the other in my room. internet connection is also there, the modem is kept in my room. but one of my cousin is there in my house and he has a laptop, the internet for his lap is taken from my modem. and now i have noticed that my cousin is visiting adult content sites and i want to block him ? is there any way. why the history he uses is being shown in my browsers history ?
I have a cisco 2800 router.. (flash:/c2800nm-advsecurityk9-mz.151-4.M4.bin, Version 12.4(13r)T11) configured DHCP, DNS, NATING and Bandwidth restriction...And to stop some social network [URL] i configured ip route 188.8.131.52 255.255.240.0 Null0 (rang of facebook address) But still i am able to open facebook.com in my network...
ADMIN-II_2811#sh run Building configuration... Current configuration : 1812 bytes ! ! Last configuration change at 17:26:33 UTC Sat Nov 24 2012 version 15.1 service timestamps debug datetime msec service timestamps log datetime msec
How do I block specific domains (pandora.com, etc.) in the Sonicwall? It seems like this would happen in the CFS but do I need a subscription for this? I don't want to subscribe to Sonicwall's filtering list, I just want to block a couple specific domains.
How to configure the 825 to block inbound traffic from a specific internet IP address ?i noticed an IP and MAC that i don't recognize that is listed as a connection to my NAS's media server ...i blocked it in the NAS configuration page, but i don't want any unsolicited traffic into my network.
I have the Qwest/Actiontec Q1000 modem/router. I go to the ip address using my web-browser and open up advanced configurations -> access scheduler. I select a computer (and it automatically adds the MAC address) and then the days/times I want the internet to be accessible. However, when I click "add" (to add my internet allowance to the scheduler list) it just says 12:00 to 0:00, which is essentially permanently blocking the internet for that computer.
I have an 1841 between my firewall and the ISP. Three interfaces - multilink to ISP, FA to my firewall, and FA to my inside network. I use the inside interface for configs aand snmp access, etc. Only my ISP-assigned fixed address block will get routed to the multilink by the ISP but I am nervous about the inside interface sitting on my LAN. I know I can remove it, but if I keep it there, how can I set up an ACL so that all traffic from the multilink interface is denied to the inside interface? I suppose another way to think about it that the inbound iface can only accept traffic from its own outside, not from the router.I think this is fairly simple but I don't want to knock down the traffic if I get it wrong.
I have Cisco ASA 8.0(5) and I need to block specific url to acees my https server in dmz ?I read about websence technology, but I think it's not free right? Also I read abotu policy inspection map's but in my case is HTTPS not http ..
I have a WAG160Nv2 and I want to block specific external ip addresses from trying to get at our server that uses the WAG160Nv2 as an internet gateway. It's not immediately obvious if this can be done from looking through the config pages.
I'm using an ASA5505 (8.4(1)) and would like to block port 80 on a specific host in the LAN so machines in other remote LANs connected via VPN can't access this port on the host. Devices in the local LAN should have access to this port on the host. Here are the commands I'm using:
-access-list block_port extended deny tcp any host 10.20.10.20 eq 80 -access-list block_port extended permit ip any any -access-group block_port out interface inside
These commands are not working as I would expect them to. When I browse to http://10.20.10.20 from a remote machine over the VPN tunnel I am able to access the host web server.
I have arequirement where in I need to allow only specific vendor made desktops/laptops to be connected to the switch and block the rest. Say I want only the HP made Laptops to be connected on the Network. and block all other vendors. such as dell, ibm etc.
I am having Catalyst 4500 switches in My network. i tried using the mac access list using the permit and deny statement and then mapping the access list to the vlan access map and then filter using the vlan id. But this doesnt work on cat 4500....the same I tested for 2950 switch and it works perfectly. are there any restrictions on 4500 or any extra configuration has to be done.
MY ISP installed one router in my lab.for internet connectivity they mail me steps :connect your Laptop directly to gi0/3 port to check internet connectivity with public ip 1.1.1.x and Gateway 184.108.40.206 with subnet mask 255.255.255.240 after connection I surprised because I am able to access only google sites like gmail,google search etc. but I am able to ping/traceroute all sites.from browser I am able to access only google sites only.In Router no firewall no such access list.
Is it possible to enable an absolute value rate limit using QOS on a HP ProCurve 5406 switch for a particular IP range on a specific port? Is there a way to configure our HP 5406 with an absolute rate limit on "WAN" port for that server's IP range? I would like to limit it to only being capable of sending 1Mbps worth of traffic over the head end at once.Everything in the documentation points towards priority queues, which as far as I can tell, isn't really what I want.Baring accomplishing this goal using rate limiting is there a better way to prevent our services from accidentally saturating this connection?i thimkong about somthing like that:
class ipv4 rate-limit-port-A1 match ip 10.136.0.0/16 any exit policy qos port-a1-ratelimit class servers-to-be-slowed action rate-limit kbps 1000 exit interface A1 service-policy port-a1-ratelimit inI'm not sure about this.
I use a router RV082 with load balancing. My problem is when I try to access a specific site, I get the error message that my IP address changes and I can not use 2 ip address. I want to specify an ip range to always use the same WAN port.