Cisco Routers :: RV016 V3 With Firmware 4.2.1.02 Constantly Rebooting?

Dec 6, 2012

I have an RV016 V3 with firmware 4.2.1.02 that is constantly rebooting making it unusable.  I have one LAN connect and 3 WAN's, 2 DSL's and one Cable Internet in a load balance config.  I have tried firmware 4.2.1.01 and it reboots also.  do I get and RMA from Linksys and send this pig back?

View 6 Replies


ADVERTISEMENT

Cisco Routers :: RV016 V1 Firmware V 1.3.2 Upgrade To V2.0.0?

Jan 10, 2013

I am trying to upgrade my RV016 hardware version 1, Firmware version 1.3.2 to firmware version 2.0.0. but can't find the file. Locating RV016_2.0.0? I am trying to upgrade to version 3.0.0.1

View 5 Replies View Related

Cisco Routers :: RV016 Shows A Browser With No Connectivity When Try To Upgrade Firmware

Jan 31, 2012

I've downloaded the file "RV0XX-v4.1.0.02-tm.bin" from Cisco's web site. The current firmware in the RV016 router is V3. I log into the router with IE9 (or even firefox), navigate to the system management section, upgrade firmware tab. Browse to the file above and click the button to upgrade. Nothing happens for a few seconds, then the browser displays cant load this page. (Same results if I use the file "RV0XX-v4.1.1.01-sp.bin" as well.)

View 1 Replies View Related

D-Link WBR 1310 Constantly Needs Rebooting

Jun 2, 2012

Why does my D-Link WBR 1310 Router constantly need rebooting? By rebooting I mean unplugging power source for 10-15 seconds then replugging it. This problem has been going on for the last 2-3 months.

View 3 Replies View Related

Cisco Switches :: SF 200-24P Switch Is Rebooting Constantly

Oct 15, 2011

I have a SF 200-24P Cisco switch that seems to be rebooting constantly, When i connect it to mains power it seems to go through a startup cycle,  in this order - i have tried this with no network devices attached and the same thing happens
 
1. Fan starts - continously runs

2. Very quick flash of all RJ45 ports.

3. After about 30 seconds, any network devices connected have an acticity light

4. After about another 45 seconds, all ports light up including the activity and POE orange LEDs for about 5- 10 seconds then go off.

5. About 10 seconds later the ports all light up again and stay on for about 5 seconds.

6. All ports go off and the cycle keeps repeating continously.
 
I have tried pinging the switch without success.I have also tried disconnecting all devices from each port with no success.At no time does the system LED on the left light up.I have tried resetting to factory default with reset pot on the left side.This is a brand new shipped switch from our cisco supplier, could it be DOA?

View 1 Replies View Related

Belkin Routers :: F5D8235-4 - V2000 Firmware 2.01.09 Usb Drive Constantly Unmounts

Feb 14, 2013

Belkin storage manager sees my 8Gb flash drive for a split second and the pops up a message about unmounting. When it connects for a split second it shows up wit a drive letter, but then disappears again.

View 2 Replies View Related

Cisco Wireless :: 5508 / AP1141 Is Rebooting Constantly?

Oct 11, 2010

I have a set up with an 5508 controller and some AP1141.i get this in the log

LogSystem TimeTrap0Tue Oct 12 14:50:23 2010AP's Interface:0(802.11b) Operation State Up: Base Radio MAC:e8:04:62:60:76:50 Cause=Radio reset due to Init. Status:NA1Tue Oct 12 14:50:23 2010AP 'APf866.f292.b28e', MAC: e8:04:62:60:76:50 disassociated previously due to AP Reset. Uptime: 0 days, 00 h 26 m 38 s . Last reset reason: power loss.2Tue Oct 12 14:50:23 2010AP's Interface:0(802.11b) Operation State Up: Base Radio MAC:e8:04:62:0b:41:20 Cause=Radio interface reset. Status:NA3Tue Oct 12 14:50:23 2010AP's Interface:0(802.11b) Operation State Down: Base Radio MAC:e8:04:62:0b:41:20 Cause=Radio interface reset. Status:NA4Tue Oct 12 14:50:20 2010AP's Interface:0(802.11b) Operation State Up: Base Radio MAC:e8:04:62:0b:41:20 Cause=Radio reset due to Init. Status:NA5Tue Oct 12 14:50:20 2010AP 'APf866.f292.b2f2', MAC: e8:04:62:0b:41:20 disassociated previously due to AP Reset. Uptime: 0 days, 00 h 26 m 44 s . Last reset reason: power loss.6Tue Oct 12 14:49:52 2010AP's Interface:0(802.11b) Operation State Up: Base Radio MAC:e8:04:62:60:84:10 Cause=Radio interface reset. Status:NA7Tue Oct 12 14:49:52 2010AP's

[code]....

The ap's are powered from a 3560 poe switch, have movet the ap's to another switch, same problem Controller is running 7.0.98.0

View 22 Replies View Related

Cisco Switching/Routing :: Polycom IP 430 Phones Constantly Rebooting?

May 29, 2013

I just installed a refurb'd 3560 48 port POE switch and configured all ports on VLAN100.  All Polycom IP 430 phones (with power adapter and without power adapter) constantly reboot every couple minutes.  Any Cisco 7960 phone does not constantly reboot and works correctly.  When I plug a small unmanaged switch into a 3560 port and then plug the Polycom phone into the unmanaged switch powering the phone with a power adapter, the phone works correctly.  So it seems that the 3560 is causing the Polycom to reboot. 

View 3 Replies View Related

Cisco Firewall :: ASA5510 Working In HA Config Now Constantly Rebooting

Mar 20, 2011

I have an ASA5510 that was working in a HA config that is now constantly rebooting itself. Here is a copy of the dump of traceback messages:

Booting system, please wait...
CISCO SYSTEMSEmbedded BIOS Version 1.0(11)5 08/28/08 15:11:51.82
Low Memory: 631 KBHigh Memory: 256 MBPCI Device Table.Bus Dev Func VendID DevID Class Irq 00 00 00 8086 2578 Host Bridge 00 01 00 8086 2579 PCI-to-PCI Bridge 00 03 00 8086 257B PCI-to-PCI Bridge 00 1C 00 8086 25AE PCI-to-PCI Bridge
[Code] .........

View 1 Replies View Related

Cisco Routers :: RV042 VPN Router Keeps Rebooting

Mar 21, 2012

I have a Linksys RV042 10/100 4-Port VPN Router with Firmware Version 1.3.13.02 and l have noticed that the Router keeps rebooting on average every couple of hours.We have it setup for Load Balancing 2 ADSL Services.

View 3 Replies View Related

Cisco Routers :: WRVS4400N V2 - Router Keeps Rebooting

Nov 28, 2012

I've got a WRVS4400N V2 Router that just keeps rebooting itself. It powers up, the red LED stays lit, it gets part way through the boot process and reboots itself. I would like to try to re flash the device, but don't know if this is possible in the condition that it is in.

View 3 Replies View Related

Cisco Routers :: RV220W Rebooting / Locking Up?

Jan 18, 2013

I've got a RV220W that for some reason has started acting a bit strange. A couple of times a day the network stops functioning, both wireless and wired. At first I thought this had to do with my newly installed laptop, that it maybe caused some hickup that made the router reboot but even when it's turned off I can still read in the logs of my NAS server (Qnap TS-419P+) that "Lan 1 is down" followed by a "Lan 1 is up" a couple of minutes after.
 
The things connected to the network by wire is my Macbook Pro (2012), the Qnap and an LG home theater system and the wireless devices are a couple of iPhones and an iPad. The problems started after new years eve and I've been running the latest firmware (1.0.4.17) for a few weeks before that.

View 1 Replies View Related

Cisco Routers :: Stop RV220W Crashing And Rebooting?

Mar 14, 2013

How do I stop the rv220w from continuously rebooting?
 
I have been keeping track of when it crashes and reboots and here is what has happened today:
 
14/03/2013 00:26 crashes and reboots
14/03/2013 07:28 crashes and reboots
14/03/2013 11:14 crashes and reboots

[Code]....

View 1 Replies View Related

Cisco Routers :: RV220W Rebooting At Random Intervals?

Jan 27, 2013

our RV220W router has been experiencing random reboots throughout the day, causing a network outage for our local network for the few minutes it takes for the router to start up again. We've seen it reboot at least 5 today alone (and the time is currently just a little over 1pm).I'm having trouble finding the reason for these reboots in the router's logs, although I find these two lines repeating in the error log:

Mon Jan 28 13:20:52 2013(GMT+0100) [rv220w][System][EVTDSPTCH] umiIoctl (18, UMI_CMD_DB_UPDATE(4)) failed. table=dot11STA row=11
Mon Jan 28 13:20:52 2013(GMT+0100) [rv220w][System][PLATFORM] /pfrm2.0/bin/bwLimitConfig /tmp/system.db 18 dot11STA 11 failed. status=-1

I'm not sure why these messages pop up, since we're not using the bandwidth limiter module of the router (granted, we do use QoS profiles to ensure our own LAN is prioritized over the guest VLAN). I'm also not sure whether this is related to the router reboots.
 
I also find the following repeated line in the warning log:

Mon Jan 28 12:50:50 2013(GMT+0100) [rv220w][Kernel][KERNEL] ERROR:endChantRecv: protocol PNAC returned !OK 

The router is currently running on firmware version 1.0.4.17 (latest official release), since we needed support for hairpin connections (as I found out in a previous thread of mine). I've seen the suggestion of downgrading to a previous firmware version in another thread, which has possibly solved it for the poster in that thread, but as we really need the hairpinning support, I don't know which firmware version is safe enough to downgrade it to, if needed.

View 10 Replies View Related

Cisco Routers :: WRVS4400N Rebooting When Streaming Video

Aug 5, 2012

I have a persistent any very annoying issue that the router reboots on it's own when I am streaming video from Netflix or other similar applications.
 
I read some reviews about this router which stated that this was a known problem, but apparently was resolved with latest firmware updates.
 
My router is new (less than 1 year). It came originally with the 2.0.1.2 firmware which I updated to the 2.0.1.3
 
That did not resolve the problem. So my question is, is there any aditional configuration necessary to stream video without interruptions, or, is this a hardware problem?

View 2 Replies View Related

Cisco Routers :: RV120W Rebooting Itself When WAN (ADSL Modem) Breaks Away

Aug 16, 2011

I have a RV120W that reboots itself when the WAN (ADSL modem) breaks away. With an old D-Link low end router, reconnecting after a failure is completed after 5 seconds and nobody cares, but the RV rebooting takes almost 2 minutes which is actually noticed...I also have some trouble getting VPN running, QuickVPN as well as normal IPsec, using either Shrewsoft or Greenbow as clients. get this router running with 3rd party VPN clients?

View 1 Replies View Related

Cisco Routers :: RV220W Rebooting Daily / Setup With SSL VPN Users

Dec 3, 2012

I have a RV220W setup with SSL VPN users, authenticating to an internal Active Directory. Maybe 5 ports forwarded and 8 external IP addresses. Besides this i have 1 data VLAN and a voice vlan on my network.
 
The reboots are on different times on a day, even on Sundays at 7 AM when noone is logged in to the network.FW is at 1.0.4.17.

View 1 Replies View Related

Cisco Routers :: What Is The Replacement SKU For RV016

Jan 27, 2013

I would like to ask if what is the replacement for RV016?  Is there any on the ISR G2 that can be set as a mulit-WAN router? Meaning can handle for more than two WAN connections.

View 2 Replies View Related

Cisco Routers :: Failing RV016 Or ISP?

Jan 22, 2010

I have a rv016 that's been in 24x7 operation since I bought it a few years back.  It is out of warranty.  It is connected to three cable modems on WANs 1-3.  Behind it are a bunch of PCs getting IPs via DHCP.  There is a gateway to gateway vpn tunnel setup on wan3 to a rv082 at another site.  There is a forwarding entry for http to an internal http server.  Everything else is pretty much default.
 
The router is primarily used to aggregate bandwidth for uploading large numbers of photos.  The systems behind the router initiate the uploads and the router automatically load balances the outgoing bandwidth.
 
This was all working fine until just recently.  The ISP is Knology who is upgrading each of the 8m/768k cable modems to 25m/5m.  They are also moving from DOCSIS 1 to DOCSIS 3.  They are currently in the middle of this upgrade and have upgraded the modems to DOCSIS 3 as well as the speeds to 12m/2m.  The problem is that the rv016 Network Service Detection, which is set to "Default Gateway" indicates that the modems fail randomly.  Usually only one will be failed, but up to two will fail the Network Service Detection simultaneously.
 
Knology insists that there is nothing wrong with their modems.  I have removed a modem from the rv016 when Network Service Detection indicates it is in a failed state and connected it directly to a computer.  It will work, but it has a different IP address and default gateway.  As soon as I connect it back to the rv016, it works there too, but on the original IP address and gateway.  I've only tried this test this twice so far, so it is a bit inconclusive.
 
Speed tests behind the rv016 are the same as directly connected to one of the cable modems.  The router works normally as it has for years.  Nothing else is acting funny.
 
So my question is, is the rv016 failing or is the ISP having problems? 

View 17 Replies View Related

Cisco Routers :: RV016 V4.2.1.02 - No Web Browsing

Jul 22, 2012

Problems on RV016 the firmware, Firmware Version :  v4.2.1.02 (Jan  18 2012 14:10:55) on port PPPoE mode. It makes the dial, but not Web  browsing correctly. The solution was to return the old version of firmware.

View 1 Replies View Related

Cisco Routers :: Upgrade RV016 From 3.0.2.01-tm To 4.0.4.02?

Nov 22, 2011

I am trying to upgrade my RV016 from 3.0.2.01-tm to 4.0.4.02. I have not received any messages  and the log has nothing. I have left the computer and switch for 2 hours and it never seems to end.  (serial no. DF0006200812).

View 1 Replies View Related

Belkin Routers :: F5D8236 Rebooting Itself Because Of Reset Button

Apr 22, 2013

Why My Belkin Router F5D8236-4 Ver 2 always rebooting itself. the router lamp is on and then the security lamp is on and then the router rebooting itself. this happening because im push the reset button. im already try to upgrade the firmware with recovering tool (Boot Loader / Tiny Kernel Version v0.02) from 192.168.2.1 but the problem still happening.

View 3 Replies View Related

Cisco Routers :: RV110W Throughput Drops Substantially A Few Days After Rebooting

May 20, 2013

My RV110W is only a few months old and apparently started ginvg me issues shortly after I got it. Since it was new, however, I only recently suspected it as the culprit!
 
I have a simple home/small business setup. A single PC wired into the lan and a handful of occasional use laptops & Android phones/tablets and a Playstation.My connection is a 30M down / 5M up cable link. I have a UBEE DOCSYS 3.0 cable modem operating in passthru mode to my RV110W.
 
Over the course of several days, thruput drops from the measured 30/5 down to as low as 1/whatever. Rebooting the RV110W restored full speed. The UBEE has never been rebooted during this time. Connecting my wired desktop PC directly to the UBEE modem give me the full 30 downlink speed even when the RV110W perfomance has dropped to 5 or even 1.
 
I am using onle a single wireless LAN, no logging turned on, no VPN, no other 'tuning of settings.As it is, this device must be rebooted every few days to restore full network speed. This is unacceptable, of course - especially from a small business class device!

View 6 Replies View Related

Cisco Routers :: Failover Setup On RV016?

Dec 28, 2011

Is it possible to have this setup on RV016?
 
WAN1: VOIP traffic (either by port or IP) + failover for WAN 2 WAN2: all other traffic + failover for WAN1 WAN3: failover for WAN1 & WAN2 with connection on demand

View 0 Replies View Related

Cisco Routers :: RV016 Not Emailing Logs

Jul 16, 2012

I have hardware version 2 and firmware 3.0.2.01 (latest firmware  available for this hardware version I believe) and I cannot get it to  email me logs.  I have entered my outlook address and our SMTP server.The  log says that it's failing each time it attempts.  I have scoured the  internet and I cannot find a solution that will work for me.  I have found some talk of adjusting an MTU setting which is supposed to be located under the firewall / general tab.

View 1 Replies View Related

Cisco Routers :: RV016 Is Not Load Balancing UDP?

Feb 22, 2012

this router (RV016v3, Firmware: v4.1.1.01-sp (Dec 6 2011 20:03:18)) in regards to it not properly directing UDP packets out of the right WAN, as per the settings stored in Protocol Binding section of [System Management, Multi-WAN].I use the section to direct all traffic from desktop computers (192.168.5.100 ~ 192.168.5.199) through WAN4, and all VoIP related traffic (192.168.5.200 ~ 192.168.5.239) through WAN2(PPPoE).Everything seems to be working well except for some of the UDP traffic from 192.168.5.200 which is seen in the log going out of WAN4 instead of WAN2.I have even created a new entry for [UDP/5060~5060]->192.168.5.200~192.168.5.200(0.0.0.0~255.255.255.255)WAN2, and placed it at the very top of the list.Here are a few lines that I've observed in the log: (Refreshed the registration of two SIP Trunks configured in our PBX)
 
Feb 23 18:11:47 2012     Connection Accepted     UDP 192.168.5.200:5060->184.72.227.214:5060 on eth4
Feb 23 18:11:46 2012     Connection Accepted     UDP 192.168.5.200:5060->50.56.59.168:5060 on ppp2
Feb 23 18:11:46 2012     Connection Accepted     UDP 192.168.5.200:5060->184.72.227.214:5060 on eth4
Feb 23 18:11:46 2012     Connection Accepted     UDP 192.168.5.200:5060->50.56.59.168:5060 on ppp2
 
There are no static routes configured, so i'm baffled by what could cause some of the UDP packets to go through the wrong WAN.All TCP Traffic from 192.168.5.200 is seen going though WAN2 as it should.

View 2 Replies View Related

Cisco Routers :: Would One Of RV016 Work With Switch

Nov 3, 2010

Would one of the 'Cisco RV016' work with a switch? I'm planning on running our work network using this device to load balance between 3 WAN connections and would like to keep the upstairs and downstairs computer users separated via a switch.Will the switch affect the load balancing or will the router still be able to detect each individual user and balance the load as seen necessary?

View 7 Replies View Related

Cisco Routers :: RV016 - WAN 1 Port Reset To 0.0.0.0

Oct 19, 2011

We are deploying a new batch of RV016 with the latest firmware (4.0.4.02).  We are using 3 WAN ports for internet access (WAN1, WAN2, WAN3)The WAN ports connects to Cicso 800 series adsl modem with DHCP.The RV016 WAN1 port setting regularly resets to 0.0.0.0 despite that the modem dhcp is still up and running.  A cold boot, resets all the configuration and WAN1 port start working againg a new ip.
 
All three WAN ports are set to automatically obtain ip from the modems.We have tried several modems, and even swap WAN ports, but the error is persistant to WAN1 only.
 
WAN2 and WAN3 are up and running without any errors.  This error is persistant with WAN1 only.We have also configured a manual ip on WAN1, and after a few hours of operation on all 3 ports, traffic on WAN1 comes to a halt.We have the same error on 3 units we received last week.All there modem are configure on different subnets.It does not seems to be a configuration error with the modem as they work perfectly well with the WAN2, WAN3  ports.We also tested a RV016 out of the box using the wizard setup, without any extra setting/configuration, and we got the same error after a few hours of operation.

View 1 Replies View Related

Cisco Routers :: Telnet RV016 Not Supporting Cli

Jan 14, 2013

I know this is a small business appliance I got my ccna certification with the hope of practice my CLI skills with a cisco device however I read in cisco docs the small business routers doesn´t support talnet neiter ssh I mean CLI, is thta true ?

View 1 Replies View Related

Cisco Routers :: RV016 2 LANs With Forwarding On Both

Mar 31, 2011

I have two LANs 192.168.0.* and 192.168.1.* (main)

I'd  like to facilitate port forwarding on the sub-LAN - is there a way to  configure the device to do so? The "main" LANs fowarding works just  fine, however I have specific ports that need to go to the sub-LAN. 

View 3 Replies View Related

Cisco Routers :: RV016 - Traffic Routing

Aug 15, 2011

I have a RV016 with an internal address of 192.168.1.1.  Also on the 192.168.1.0 network is a gateway server that the rest of my clients sit behind.  The clients are on a 172.16.3.0/24 network.  All of the gateway server does is forward the packets.  It does not NAT.  There is a static route to 172.16.3.0 on the RV016.
 
So my question is how do I get traffic from 172.16.3.0 to route through the RV016?  Computers on the sub net can ping the RV016 and get a reply so I know the gateway server is forwarding the packets between the two sub nets just fine and that the static route on the RV016 works.  Any traffic that tries to go beyond the RV016 never makes it.  It just disappears at the RV016.  I have checked all of the ACLs and they should let all internal traffic through.

View 3 Replies View Related

Cisco Routers :: Possible To Configure RV016 With 5 WANS?

Sep 5, 2011

I have 11 available IPs at a data center and have 5 servers I want configure - each with its own LAN, not to be networked together (used for web, ftp, sql and other webs services).  Is it possible to configure the RV016 with 5 WANS, each attached to a specific port with its own LAN?
 
Am this even the right considerations for this router as I would just have normally purchased 5 routers and attached them individually to each server with their own specific WAN and LAN?

View 2 Replies View Related

Cisco Routers :: RV016 - No Support For TZO DDNS

Nov 26, 2011

I just purchased a RV016 router, upgrading from an older Linksys router only to find out that there was no support for TZO DDNS.  I have used TZO for years now and don't really want to change to another service. Any way to request this from Cisco engineers for future firmware upgrades?

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved