Cisco Switches :: SF 200-24P Switch Is Rebooting Constantly
Oct 15, 2011
I have a SF 200-24P Cisco switch that seems to be rebooting constantly, When i connect it to mains power it seems to go through a startup cycle, in this order - i have tried this with no network devices attached and the same thing happens
1. Fan starts - continously runs
2. Very quick flash of all RJ45 ports.
3. After about 30 seconds, any network devices connected have an acticity light
4. After about another 45 seconds, all ports light up including the activity and POE orange LEDs for about 5- 10 seconds then go off.
5. About 10 seconds later the ports all light up again and stay on for about 5 seconds.
6. All ports go off and the cycle keeps repeating continously.
I have tried pinging the switch without success.I have also tried disconnecting all devices from each port with no success.At no time does the system LED on the left light up.I have tried resetting to factory default with reset pot on the left side.This is a brand new shipped switch from our cisco supplier, could it be DOA?
View 1 Replies
ADVERTISEMENT
Jun 2, 2012
Why does my D-Link WBR 1310 Router constantly need rebooting? By rebooting I mean unplugging power source for 10-15 seconds then replugging it. This problem has been going on for the last 2-3 months.
View 3 Replies
View Related
Oct 11, 2010
I have a set up with an 5508 controller and some AP1141.i get this in the log
LogSystem TimeTrap0Tue Oct 12 14:50:23 2010AP's Interface:0(802.11b) Operation State Up: Base Radio MAC:e8:04:62:60:76:50 Cause=Radio reset due to Init. Status:NA1Tue Oct 12 14:50:23 2010AP 'APf866.f292.b28e', MAC: e8:04:62:60:76:50 disassociated previously due to AP Reset. Uptime: 0 days, 00 h 26 m 38 s . Last reset reason: power loss.2Tue Oct 12 14:50:23 2010AP's Interface:0(802.11b) Operation State Up: Base Radio MAC:e8:04:62:0b:41:20 Cause=Radio interface reset. Status:NA3Tue Oct 12 14:50:23 2010AP's Interface:0(802.11b) Operation State Down: Base Radio MAC:e8:04:62:0b:41:20 Cause=Radio interface reset. Status:NA4Tue Oct 12 14:50:20 2010AP's Interface:0(802.11b) Operation State Up: Base Radio MAC:e8:04:62:0b:41:20 Cause=Radio reset due to Init. Status:NA5Tue Oct 12 14:50:20 2010AP 'APf866.f292.b2f2', MAC: e8:04:62:0b:41:20 disassociated previously due to AP Reset. Uptime: 0 days, 00 h 26 m 44 s . Last reset reason: power loss.6Tue Oct 12 14:49:52 2010AP's Interface:0(802.11b) Operation State Up: Base Radio MAC:e8:04:62:60:84:10 Cause=Radio interface reset. Status:NA7Tue Oct 12 14:49:52 2010AP's
[code]....
The ap's are powered from a 3560 poe switch, have movet the ap's to another switch, same problem Controller is running 7.0.98.0
View 22 Replies
View Related
Dec 6, 2012
I have an RV016 V3 with firmware 4.2.1.02 that is constantly rebooting making it unusable. I have one LAN connect and 3 WAN's, 2 DSL's and one Cable Internet in a load balance config. I have tried firmware 4.2.1.01 and it reboots also. do I get and RMA from Linksys and send this pig back?
View 6 Replies
View Related
Jan 18, 2013
My problem is that the switch all of the sudden doesn't boot up anymore. The System LED constantly flashes, after probably 40-50 seconds or so it constantly lights for a second, afterwards all the lights on the ethernet ports light up for a second and the process starts all over again! The console messages:
Device configuration:Slot 1 - SG300-10PDevice 0: GT_98DX3033B (AlleyCat2)
-------------------------------------- Unit Standalone --------------------------------------
Tapi Version: v1.9.5Core Version: v1.9.519-Jul-2012 17:55:03 %INIT-I-InitCompleted:
[Code].....
View 3 Replies
View Related
May 29, 2013
I just installed a refurb'd 3560 48 port POE switch and configured all ports on VLAN100. All Polycom IP 430 phones (with power adapter and without power adapter) constantly reboot every couple minutes. Any Cisco 7960 phone does not constantly reboot and works correctly. When I plug a small unmanaged switch into a 3560 port and then plug the Polycom phone into the unmanaged switch powering the phone with a power adapter, the phone works correctly. So it seems that the 3560 is causing the Polycom to reboot.
View 3 Replies
View Related
Mar 20, 2011
I have an ASA5510 that was working in a HA config that is now constantly rebooting itself. Here is a copy of the dump of traceback messages:
Booting system, please wait...
CISCO SYSTEMSEmbedded BIOS Version 1.0(11)5 08/28/08 15:11:51.82
Low Memory: 631 KBHigh Memory: 256 MBPCI Device Table.Bus Dev Func VendID DevID Class Irq 00 00 00 8086 2578 Host Bridge 00 01 00 8086 2579 PCI-to-PCI Bridge 00 03 00 8086 257B PCI-to-PCI Bridge 00 1C 00 8086 25AE PCI-to-PCI Bridge
[Code] .........
View 1 Replies
View Related
Apr 19, 2012
we are running 43 Cisco AIR-AP1252G-A-K9 wireless access points using POE in our facility. These are connected to Cisco switches in various locations throughout the warehouse. I have read many varying opinions on this matter some say do reboot some say never. Do these access points and switches need to be reset on a routine basis to insure reliability and performance?
View 2 Replies
View Related
Feb 12, 2013
I have observed a situation where one of our cisco switch 3560 is rebooting daily at periodic times.We have checked the power cables and source everything is fine and still clueless whats causing the issue. [code]
View 13 Replies
View Related
Oct 23, 2012
I'm having some trouble with a 4510 Switch Line Card. I need some recomendations for troubleshooting it.We have some PoE phones connected to the card number 3. When those phones were restarted, they did not go up again. In order to discard wiring issues, we connected the phone directly to the card 3, and the phone did not go up. If the phone is connected to a different card, it goes up correctly.
Additionally, to restore the service, these phones were migrated to other cards, but when we disconnect the equipment, ports in line card 3 remain in an up / up state (and nothing is connected to those ports!!), and only reflect the actual state after restarting the port.What steps could I do in order to troubleshoot this issue?. What should I look for, or how do I discriminate the problem? Might it be a hardware issue, a PoE issue?
View 3 Replies
View Related
Aug 4, 2011
In the last month or so I have had to reset my router every 30 min or so this is very annoying and would like to know what could cause the problem.
View 2 Replies
View Related
Aug 19, 2012
We have a 3750x switch with some issues on the arp. Our servers become unreachable for some time, buy when I clear the arp cache, I am able to ping the server again. I have tried adjusting the arp timeout but I don't think doing so would be the permanent solution.
View 9 Replies
View Related
Jul 23, 2012
I'm watching a video streamed from my laptop and the signal is constantly being dropped. I suspect the D-Link DES-105. I have another Ethernet switch on the system as well but it is a Gigabit unmanaged switch from D-Link and has worked well with video streams. I've removed the DES 105 from the circuit and videos play fine. Should I dump to DES-105 for another Gigabit switch? SOme say I have a bad cable somewhere but I have tested all and have not found a problem.
View 2 Replies
View Related
Mar 19, 2012
I have a Cisco SG300 switch on which trunks are configured. I have a server which sits on the switch via a trunk link of four network cables (4 Gbps total)on which LACP is enabled. I'm having trouble connecting to the server using VNC from a computer on the network. It doesn't happen all the time though, it's just random.
On looking at the logs of the switch, I saw something unusual. The trunk that connects the switch to the server is constantly removing all the member ports and adding them back again after a few minutes interval. That causes the trunk link to flip on and off all the time. What could be the reason that's causing it to happen? I know it could be the network cable but I'm using brand new cables and the server also is brand new.
View 6 Replies
View Related
Mar 16, 2012
I have a 300 series switch with VLAN1 untagged, VLAN 15,5,100 tagged. I want say ports 1-12 to use one uplink/trunk and 13-24 to use another uplink. All ports should have the same default VLAN1 and be tagged for 5,15,100. I'm trying to ease the load on two wireless uplinks(one is a Cisco 1242AG and the other is a UBNT PowerBridge.) I don't want to add another switch. Model: SF 300-24P
View 5 Replies
View Related
May 9, 2011
I have a question, does the SG300-28 support VTP and STP?. I want to add it to my network's VTP domain so I don't have to manage vlans manually on the SG300-28 and also be able to configure STP to keep my network loop free.
View 2 Replies
View Related
Jun 12, 2011
i found that cisco small business SF302 PoE managed switch connect with the end device (RFID component) would causing packet drop issue.how should i isolate the issue and proper troubleshooting? would it cause by the PoE issue, or the 10/100 base etc.
View 5 Replies
View Related
Jun 13, 2011
For test I used 2 Switch that name "ESW X" and "ESW Y" I have 2 network that I named "Network A" and "Network B" I build 2 VLAN for each network that named Vlan 2 for Network A and Vlan 3 for Network B, I don't use Vlan 1 because it's the default Vlan
Configuration ESW X:
port e1 : ACCESS PORT on UNTTAGGED Vlan 2
port e2 : ACCESS PORT on UNTTAGGED Vlan 2
port e3 : ACCESS PORT on UNTTAGGED Vlan 3
port e4 : ACCESS PORT on UNTTAGGED Vlan 3
port g3 : TRUNK PORT with UNTTAGGED Vlan 1(default) and TAGGED Vlan 2 and Vlan 3
[code]....
Each Vlan can't communicate between the two switch, I think they're a problem in my vlan/port configuration?
View 2 Replies
View Related
Feb 12, 2013
I would like to configure a switch to act like a Hub. I know about the mirroring port configuration, but unfortunately is not enough for me. Is it possible to do that with the switch that I have (i.e. SG 200-08) ? If not do you know a switch on which I can configure it like a hub (that mean no flow control between physical ports).
View 1 Replies
View Related
Aug 29, 2011
Have deployed a few of these - and am truly frustrated that I cannot see then in the topolgy, let alone actually manage them. Why such a ubiquitous switch is not supported.
Even the SmartPort utility is useless - CCA (3.3.1 and earlier) gives an error saying a port is incorrectly configured (I pluggged it into an exp port on the UC560 as I gave up trying to get a working uplink to an ESW-540-24P).
The Smartport port function wants the exp port (on the UC560) to be configured as a "Phone/Desktop" - if I try to change it to a "switch", it refuses to accept it saying the "Macro is unsuitable - or similar"
View 2 Replies
View Related
Dec 11, 2011
I am trying to setup an ACL on SG 300 switch. I want to create an ACL that enables hosts on our guest network to obtain IP addresses from a server on our "internal" network but they should not be able to reach any other resorses on that network. I set it up as follow, but it does not work the way i want. I have also bind interfaces to the ACL.
View 4 Replies
View Related
Aug 30, 2011
I am interesting is ESW-520-24-K9 switch supports GLC-LH-SM SFP? In official data sheet there is no information about that. it is supported and I am interesting if it is true ?
View 5 Replies
View Related
Aug 10, 2011
ossible to connect a pair of switch serving the same segment (active/passive) into 1 switch?
View 6 Replies
View Related
Sep 10, 2011
I am having an issue with LAG configuration on a Cisco SG300 52 switch. I have connected four Ge ports on the switch to the four NICs of a Dell R710 Server on which I installed Windows Server 2008 R2. Without LAG configured, these ports would forward traffic to and from the Dell server fine.However, if I configure LAG on the ports with LACP enabled, then they would not forward any network traffic. Debugging shows that the ports are up but their forwarding status show N/A. Am I missing any configuration? Can I configure LAG on edgeports?
View 2 Replies
View Related
Jul 18, 2011
I have configured stack with 2 sge2010p switches. I want to connect this stack to the HP procurve switch using port agregation (LAG) technique. I want to use one ge port on each sge switch.How to configure it? Will it work witch port agregation on procurve?
View 2 Replies
View Related
Jul 10, 2012
Any way to access the usual command line interface instead of using the GUI or Telnet/SSH interfaces on the Cisco Small Business SFE2010P switch? Note that the console port is not working at the moment...
View 4 Replies
View Related
Aug 21, 2011
I turned unplugged it and plugged it back in. Now its blinking green power LED. Is it dead?
View 2 Replies
View Related
Oct 16, 2011
We just purchased 8 managed switches POE to swap out our existing in preparation for our new phone system. We installed them all after configuring with static IP. Deployed... and all but two work fine. Any tips for troubleshooting why two of them do not work? There are a couple other switches in the building. Could it be that a switch "upstream" from the two non-functioning switches is causing an issue? If so, how do I find out? When we put back the two "dumb" switches all was fine.
View 1 Replies
View Related
Aug 22, 2011
SRW 2048-EU(webview) switch will support how many SFP minigibic whether 2 or 4 ?
View 1 Replies
View Related
Nov 9, 2012
I want to create a network with the following switch SF 300 - 08.I am not use to GUI.I am having problems setting the settings.Currently, i have assigned each port with a vlan 1 to 8 for ports 1 to 8.How do i do an inter vlan with the GUI? Also, i want to restrict port 7 and 8 to certain ports only. Example:Port 7 and 8 can read port 5 and 6 but not others?
View 9 Replies
View Related
Feb 25, 2013
I have fiber optics no router One static IP address, when connect SF 200 the system LED flashes and there is conductivity.I checked ther is no setting for static ip,Gateway,DNS, so is this unit only for Dynamic address
View 3 Replies
View Related
Jul 20, 2011
I have an ESW 520 8-Port switch with a management ip address of 192.168.10.2 /24 After I reboot it, I can successfully ping it from a pc with an ip of 192.168.10.123 for about 50 consecutive times.After that, I get a "Destination host unreachable" (this icmp message is sent by my pinging pc (192.168.10.123).This obviously seems like a bug.Whenever I reboot it, it goes through the same sequence.
View 2 Replies
View Related
Jun 13, 2011
I have 2 (and maybe soon 5 more) 7940G phones to add to my network, which already has a Netgear POE capable switch. I've since discovered that early Cisco POE isn't the same thing as current POE, and the switch doesn't power the phones.
I was looking at adding a Cisco SD208P 8-port switch to power the phones, but I soon discovered it only has 4 POE ports, and I'm not sure that this switch will even power the 7940G phones. And if the other 5 phones show up, I'll need two of those switches with no room for expansion on the voice network.
Will this switch power those phones?Is there another small switch available so I don't have to replace my existing switch infrastructure to get these phones to work? Or do I need to scrap the phones and get something newer that will work with the current POE standards?
View 2 Replies
View Related
