I am trying to setup an ACL on SG 300 switch. I want to create an ACL that enables hosts on our guest network to obtain IP addresses from a server on our "internal" network but they should not be able to reach any other resorses on that network. I set it up as follow, but it does not work the way i want. I have also bind interfaces to the ACL.
View 4 RepliesI have a dell powerconnect 2848 switch and setting up a vlan 3 an make port 1 mngt, port 48 uplink to layer 3 switch and tag vlan 1 and 3 to port 48 with cli commands for this setup. and also to untag ports 2-10 for computers
View 1 Replies View RelatedI'm going to have several SG300-28P switches to setup. I'll need to create multiple vlans for data, voice, and wireless traffic. I have the following questions in setting up this configuration:
VLAN 1 Management
VLAN 100 Data
VLAN 200 Wireless
VLAN 300 Voice
1) For managing the switches via IP, will LAN1 be the default management network? Should I create a seperate VLAN for managing the switches?
2) For uplinking the switches together, I plan to trunk a port to connect the switches together. What's the configuration on the trunk port to forward all vlans from one switch to another?
3) On some ports, I want to configure a trunk for two vlans (Data and Voice) where the phone has a pass through for PC. The phone supports tagging for the PC and the VoIP traffic. For example on port 10, would VLAN 100 and 300 be set to tagged?
I want to setup an home network with a wireless router and use multiple switches for wired connections through out my home. I currently have an Airport extreme hooked up to a cable modem and a leviton gateway hooked up to the Airport. The 2 computers connected to the Leviton are on a windows 7 homegroup and share fine, but won't share or discover any wireless device connected to Airport. My main goal is to have a wireless/wired network with all computers sharing information with each other. I want 2-3 wired switches/gateways with a min of 2 devices connected to each, connected to my wireless router whiich is connected to cable modem.
View 3 Replies View RelatedI'm trying to setup following scenario which is working with no issue on netgear switches (like GS108) but I have not been able to get it to work on Cisco SG-200 I did quite a bit of reading here on many post but nothing seems to work.
View 6 Replies View RelatedWe are in the process of switching to a new internet provider in our office and have run into some problems. Our old setup was with AT&T, where they provided a managed router which linked to our internal switch and also provided NAT to the internal IP of our email server.Our new setup right now is just the internet coming in through a cable connected to a switch, we were told we needed to provide our own router. Someone donated a Cisco 2900.What should our proper set-up be? Should the internet come in directly to the router and then to our switch, or should it go to the switch they provided, then the router, and then our switch?Also, there seems to be some confusion about whether or not we need anything else to get the internet to work. There are slots for network cards in the router. Does it come with at least one built in we can use, or do we need to provide one?
View 1 Replies View RelatedWe have a potential new customer who is wanting to deploy a guest WLAN. I am happy doing this via a VLAN on the WAP4410N series AP’s. I would then create the relevant VLAN’s on the switch. Can each VLAN be assigned an IP address and allowing me to be able to add a static route on the router pointing the traffic for the Guest VLAN back to the switch?
View 1 Replies View RelatedIm trying to get my head around my new cisco SG 300 switch. I have used the Linksys SRW range before and configured it using teraterm and method described in the link below:
[URL]
As im fimilar with this method and the commands ideally I'd like to use this on the SG 300 range as well. Failing that, is it possible to use another method which uses the same commands which can be easily copy and pasted for setting up multiple switches with the configuration?
I have the following setup using two SF302-08P PoE switches:
1st floor
=========
Switch #1 <-------> private network
<-------> public network
[Code].....
I have tried to make the config in switch #2 identical to switch #1, but something is still wrong. Is this most likely a VLAN setup problem, or what?
I would like to create 3 x VLANs on an SG 300-28P and have them completely isolated from each other, for example ports 1 - 12 on VLAN 1, ports 13 - 24 on VLAN 2 and ports 25 - 28 on VLAN 3. No communication between any of the VLANs.
Any simplest way to achieve this?
I'm trying to setup an ACL on my SG300-20 to enable FTP and a few other protocols to a server, but I'm running data that returns on different ports (ie active FTP).
Below is a sample:
-------------------------------------------
Extended IP access list Protocol_Restriction
permit tcp any ftp any any
-------------------------------------------
Now that works great to allow a connection, but with active ftp when the data tries to come back on a different port (I assume) it is just hung up as all other ports are denied.
I event tried allowing all ports to come back from the server:
-------------------------------------------
Extended IP access list Protocol_Restriction
permit tcp any ftp any any
permit ip any host 192.168.0.100
-------------------------------------------
But that also didn't work seem to work.
I've played around with this in layer2 and layer3 to no avail. I've also seen many tips on applying in and out to the various interfaces, but that doesn't seem to work. Is that something that is only available on higher end switchers/firewalls?
setting up two VLANs for my WAP: one for all local network and internet traffic and one for just (guest) internet traffic. I just purchased both devices but I don't know if I have the option for free Cisco phone support.
View 1 Replies View Relatedi have a dlink dir-412 3g router. i want to add one ipcam with the router. but i have no static ip. so how can i configer ipcam in this router.
View 2 Replies View RelatedI have a Synology 1512+ and trying to setup Link Aggregation but no success. I have configured LAG Management with LACP enable or disable but still failed.
At the Synology 1512+ setting page, there are 2 options: IEEE 802.3ad Dynamic Link Aggregation and Network Fault Tolerance (Non-802.3ad network enirovement), I selected IEEE802.3ad, which i think S200-18 should be able to support. right?
I'm trying to set up a new switch, a 4506e, for a remote site. Most of our newer remote sites are using a 4506 and this is the first time I'm working with a 4506e. Our standard configuration, which was in use before I started here, has QoS settings. I'm not that familiar with QoS. Most of the QoS commands in our standard config aren't working in the 4506e. Does the 4506e have QoS? Is there some guide as to setting it up? Below are excerpts from the config we're using that are QoS related:
qos dblqos map dscp 32 33 34 35 36 37 38 39 to tx-queue 2qos map cos 3 to dscp 26 qos map cos 5 to dscp 46 qos aggregate-policer XYZ_AGG 64 mbps 8 mbyte conform-action transmit exceed-action drop qos!class-map match-all match_XYZ match access-group 142!policy-map police_XYZ class match_XYZ police aggregate XYZ_AGG!interface GigabitEthernet4/1 description server qos dscp 48!interface GigabitEthernet4/30 description server service-policy input police_XYZ!interface GigabitEthernet4/48 description upstream connection qos trust dscp tx-queue 1 shape 98 mbps tx-queue 2 shape 1 mbps tx-queue 3 priority high
I have 3 different office location and I need to set up a LAN so that all three are connected and can share info?
View 1 Replies View RelatedAt my company, we lease 3 static public IP addresses from 1 ISP. We want to have 3 separate networks that each use one of the IP addresses. Network 1 is the computer network, network 2 is the VOIP network, and network 3 is the security camera network. I am trying to determine the best way to do this. I have come up with 2 solutions in my head, but I'm not sure if they will work or not. I would like to get some input. Solution 1:Solution 1 looks something like this. Fiber box -> Router-> 3 switches. There would be one WAN input on the router, that would have a static route to 3 different LAN ports. For example, address 24.244.208.101 would be assigned to LAN port 1, 24.244.208.102 would be assigned to LAN port 2, and 24.244.208.103 would be assigned to LAN port 3 (by assigned, I mean have a static route to it). Is there some type of router that is capable of doing this? Solution 2:Solution 2 looks something like this. Fiber box -> Switch -> 3 Routers. The ethernet cable would run from the Fiber Box to a switch, and then 3 routers would be plugged into the switch. Each router would have the Static information configured in them. Would both of these methods work? If so, which would be the best way to go?
View 2 Replies View RelatedI did RECOVERY on my computer. Its a Compac Windows XP Home edition. This computer runs off of my main computer by a router & adapter. My router & adaptor are showing green but the Internet is showing red. Its becuz my high speed Internat service is ATT.my.yahoo.com. which comes through IE. On my newer computer all is fine. My IE works good & all is working. but my IE on my older one which runs with the router wont set up.
View 1 Replies View RelatedI Have a Computer Ready for setup as a Server in the LAN Connection:
Windows 7 Professional.
Another 2 Computers for LAN Connection:
1st Computer is a Windows 7 Professional (Connect as LAN)
2nd Computer is also Windows 7 Professional (Must connect using a Wifi D-Link)
Another 2 Computer for LAN Connection:
Windows XP: Must Connect Using LAN port.
1 Computer:
Windows 7 Home Edition: Must Connect Using LAN port
2 Laptops:
1st Laptop is using Windows 7 Ultimate.
2nd Laptop is a Vista.
How to Connect these Computers to the above mentioned computer ready for setup as as Server?
I want to setup SQL Server on my internal home network, and make it available to my colleagues.
[code]...
Win 2008 Server with SQL Server.What do I need to do to allow my colleagues to connect to the SQL server from their computers, in their offices (not on my network)?For example, because I have a DHCP address from my ISP, do I need to use something like DynDNS to track my IP address?
I had this small internet cafe with 15 units pc. and browsing the web is not that stable. i have to unplug the internet modem everytime i can't connect to the internet.I think it has something to do with the settings that was in the router since it was just configured by a tech guy which i think not 100% sure of what he did, though it can connect to net for sometime but most of the time it is down.
View 5 Replies View RelatedHow to set up more than 40 pc's with out internet connection using linksys switch.
View 3 Replies View RelatedOK i'm re-organising my network setup, most of my devices in my room are hard wired through Ethernet but some devices in the house need to run wireless.Currently i am running a super hub that has been configured into just modem only and a wireless router that gives wireless and hard wires up to 4 devices. Im wanting something that can be mounted out the way like an Ethernet switch but give it wireless accessibility too. I see you can buy access points to connect to your Ethernet switch device but will it give ample wireless connectivity if im running 4+ hardwired devices?I have recently been upgraded from 30Mbps to 60Mbps, this is fed from cable connection to the modem.
View 5 Replies View RelatedWe have multiple switches(Cisco 4510, 4507R, 3560's) within our network. I've been looking over the port settings between them and noticed that not all ports that are connected directly from switch to switch are trunked the same. Some are desirable on one switch and forced truck on the other switch.
View 5 Replies View Relatedi have a question about the proper method to setup up vlan(s) on a sg200 switch with a sv220w router. Should i setup the vlan on the router or the switch? I have small office setup, i need atleast 2 vlans to separate the networks. i want both to have internet access but be completely isolated from each other.
View 5 Replies View RelatedI'm new to managed networking. So I'm having trouble understanding how to set up my switches properly. I have a closed network with about 20 switches and 2 IDF's. No router, and no internet. I have a SLM 2024 in want to have 4 ports set up with a VLAN. I have another SLM2024 I want to be on the same VLAN some where else. Switch 1 uses port 24 GBIC as and up link port to one of the IDF's. Switch 2 uses ports 12 and 24 copper(LACP) to make a hop from another switch(ports 1 and 13 LACP)which inturn is connected to the same IDF on port 24 GBIC. How do I set up switch 1 ports 7,8,19,20? Also, how do I set up switch 2 ports 7,8,19,20? VLAN 11
View 1 Replies View RelatedWe have a Cisco 887 router and a Cisco SG-200 switch.We'd like to setup trunking between these 2 devices for multiple VLANs on the switch to be made available on the router.
With previous routers, you could set the router up in the configuration 'router-on-a-stick' and VLANs worked like a charm but the 887 no longer support sub-interfaces.So how can you get trunking working between the 2 devices?
Is there a VTP configuration menu for the SG-200 which we can setup in order for it to talk 'VTP' with the 887 router??
I currently have IOS image cat4500e-entservices-mz.122-53.SG5.bin. According to my research it appears SPAN is supported on this OS. However, after looking at procedure notes using websites like here:
[url]... I cannot find and obviously not figure out how to use the SPAN command. My main objective is to simply setup a port mirror on one of my TenGigabitEthnet interfaces and from what I read SPAN is the best way to setup a tap interface on a cisco switch.
I am trying to setup SNMP v3 on a 4948E switch here is what I have done so far:
snmp-server location "location"
snmp-server contact IT Admins
snmp-server group SNMPgrp v3 priv read SNMP-ro write SNMP-rw access 80
snmp-server user snmp_user SNMPgrp v3 auth sha xxxxxxxxx priv aes 128 xxxxxxxx access 80
What else am I missing and how can I confirm that it is configured correctly?
I have VOIP and was provided a modem, a Tilgen Router (Vood 452_A). I also currently have a Linksys WRT54G router. I also have a home surveillance system with a DVR that can be accessed via the net. I am trying to allow the ports to open so that traffic can navigate down to the DVR.My IPs:My VOIP has provided me with 6 static IP addresses. For sake of this issue they are:
67.xx.xxx.153, through .158My subnetmask is set to:
255.255.255.248My Settings:
The Modem is connected to world. To the modem I have the Tilgen Router connected. The Tilgen is set with an ip of .153 and the subnetmask listed above. DHCP is turned on and has IP range set for .154-.158. It is set in Bridge Mode with NAT and Firewall turned off. To that I have the WRTG54G router connected and assigned the router an Static IP of .154.. The cable is going into the Linksys WAN port.From a computer connected to a LAN port on the WRT54G, I see my public IP as .154, currently my internal IP is 192.168.1.15 so I believe I have to assign one of my Static IPs to this PC, however when I try to connect to the Linksys Router (.154) from the outside web, I am get a time out error. (also from a ping test.) My thoughts are to assign the Linksys to DHCP and use a range of .155-.158 to give each lan item a static IP. My question is will this work? Will each item in the network have its own IP and if I forward the port to the DVR that i needed, ie 80 for web client or 6100 for desktop client, will that forward through?Or do I set it to Router Mode and use the Tilgen to assign the ips.
On the Tilgen I also have an option for a DHCP relay or to turn off DHCP.
For clarification here is the setup chain
Broadband/DSL Line>>Tilgen Modem>>(LANPort1)Tilgen Router(LAN Port2)>>(WAN) Linksys(LANPort1)>>DVR/Computers
Found this walkthrough on setting the WRT54G into a Switch. If I did this, in theory the VOOD would assign those computers/dvr connected downstream via the WRT54G a static ip from my range set on the router. Then in theory I would not need to port forward port 80 since the DVR would be on its own public IP.?
how to open the tp-link interface setup for my TD-W896ON? i have a user and a password but where do i add them ??
View 1 Replies View RelatedWe recently moved 8 pc's from a room where they each had port on the switch to a room where there is only one port for all of them. I setup a DLINK DIR632 Router in there and they connect thru the one port thru the switch to the gateway which gets them out to the internet.The problems is I need to be able to remote desktop into these 8 PC's and I need them to be able to print to the network printer. I am using a Linksys WRT54G Broadband router as the gateway connecting the switch to the internet. The DLINK's dhcp server is on for the 8 PC's. The Linksys' dhcp server shows the DLINK as IP 192.168.1.19 on the network.I know I have to use advanced routing settings but I'm not sure about how what to make the subnet mask and IP's on both routers. I believe I need to turn off the dhcp server on the DLINK and have the Linksys' dhcp server serve all of the PC's but I'm not sure if thats the best way or if its possible.. I don't want to hack out fix only to find it breaks 3 days later.I used to do this stuff all day long in the 90's but its been a while and to me its like calculus.
View 13 Replies View RelatedI'm looking to setup Inter-VLan routing on a 4800G switch.
I'm looking for all workstations (VLAN1) to be able to talk to the windows network (VLAN2) and to our Novell network (VLAN3)
but I don't want Windows (VLAN2) and Novell (VLAN3) talking to each other. Is this possible accross a single switch? I have 7 switches available to use if needed.