Routers / Switches :: Did A Recovery And IE6 Page Won't Setup
Mar 13, 2011
I did RECOVERY on my computer. Its a Compac Windows XP Home edition. This computer runs off of my main computer by a router & adapter. My router & adaptor are showing green but the Internet is showing red. Its becuz my high speed Internat service is ATT.my.yahoo.com. which comes through IE. On my newer computer all is fine. My IE works good & all is working. but my IE on my older one which runs with the router wont set up.
Is there a way to quickly disable Wi-Fi on a N-150 from the router setup page? I have looked on my admin page but I don't see it. I just want to be able to turn the radio on and off from the PC that is connected via ethernet.
Motorola wr850gp wireless router. The default ip is 192.168.10.1. I attempted to use it as a wireless access point and now it is not working at all. I tried connecting the router LAN port to the computer and 192.168.10.1 pulls up nothing.I tried connecting the modem to the WAN port and the LAN port of the router to the PC, but then I have no internet access at all. I tried resetting the router, still nothingAll lights on the router are green. I don't know what the heck is going on?
I cannot open the config page of beetel adsl2 router using 192.168.1.1I have connected my laptop to router via Lan cable. Now when I give the ipconfig, I get some random IP and does not get the default gateway: Autoconfiguration IPv4 Address. . : 169.254.129.188 Subnet Mask . . . . . . . . . . . : 255.255.0.0 Default Gateway . . . . . . . . . :I cannot ping 192.168.1.1 nor 169.254.129.1 thus the web page of router cannot be opened.This all happened after I reset my router.
I want to setup an home network with a wireless router and use multiple switches for wired connections through out my home. I currently have an Airport extreme hooked up to a cable modem and a leviton gateway hooked up to the Airport. The 2 computers connected to the Leviton are on a windows 7 homegroup and share fine, but won't share or discover any wireless device connected to Airport. My main goal is to have a wireless/wired network with all computers sharing information with each other. I want 2-3 wired switches/gateways with a min of 2 devices connected to each, connected to my wireless router whiich is connected to cable modem.
Signed onto pc as admin, logged into router with correct user name and password. No page in the browser based configuration displays the complete information for the page. Menus are missing as are option labels, etc. The last time I accessed the router (about a year ago) I didn't have this problem.
At my company, we lease 3 static public IP addresses from 1 ISP. We want to have 3 separate networks that each use one of the IP addresses. Network 1 is the computer network, network 2 is the VOIP network, and network 3 is the security camera network. I am trying to determine the best way to do this. I have come up with 2 solutions in my head, but I'm not sure if they will work or not. I would like to get some input. Solution 1:Solution 1 looks something like this. Fiber box -> Router-> 3 switches. There would be one WAN input on the router, that would have a static route to 3 different LAN ports. For example, address 220.127.116.11 would be assigned to LAN port 1, 18.104.22.168 would be assigned to LAN port 2, and 22.214.171.124 would be assigned to LAN port 3 (by assigned, I mean have a static route to it). Is there some type of router that is capable of doing this? Solution 2:Solution 2 looks something like this. Fiber box -> Switch -> 3 Routers. The ethernet cable would run from the Fiber Box to a switch, and then 3 routers would be plugged into the switch. Each router would have the Static information configured in them. Would both of these methods work? If so, which would be the best way to go?
We are in the process of switching to a new internet provider in our office and have run into some problems. Our old setup was with AT&T, where they provided a managed router which linked to our internal switch and also provided NAT to the internal IP of our email server.Our new setup right now is just the internet coming in through a cable connected to a switch, we were told we needed to provide our own router. Someone donated a Cisco 2900.What should our proper set-up be? Should the internet come in directly to the router and then to our switch, or should it go to the switch they provided, then the router, and then our switch?Also, there seems to be some confusion about whether or not we need anything else to get the internet to work. There are slots for network cards in the router. Does it come with at least one built in we can use, or do we need to provide one?
I had this small internet cafe with 15 units pc. and browsing the web is not that stable. i have to unplug the internet modem everytime i can't connect to the internet.I think it has something to do with the settings that was in the router since it was just configured by a tech guy which i think not 100% sure of what he did, though it can connect to net for sometime but most of the time it is down.
I have VOIP and was provided a modem, a Tilgen Router (Vood 452_A). I also currently have a Linksys WRT54G router. I also have a home surveillance system with a DVR that can be accessed via the net. I am trying to allow the ports to open so that traffic can navigate down to the DVR.My IPs:My VOIP has provided me with 6 static IP addresses. For sake of this issue they are:
67.xx.xxx.153, through .158My subnetmask is set to:
The Modem is connected to world. To the modem I have the Tilgen Router connected. The Tilgen is set with an ip of .153 and the subnetmask listed above. DHCP is turned on and has IP range set for .154-.158. It is set in Bridge Mode with NAT and Firewall turned off. To that I have the WRTG54G router connected and assigned the router an Static IP of .154.. The cable is going into the Linksys WAN port.From a computer connected to a LAN port on the WRT54G, I see my public IP as .154, currently my internal IP is 192.168.1.15 so I believe I have to assign one of my Static IPs to this PC, however when I try to connect to the Linksys Router (.154) from the outside web, I am get a time out error. (also from a ping test.) My thoughts are to assign the Linksys to DHCP and use a range of .155-.158 to give each lan item a static IP. My question is will this work? Will each item in the network have its own IP and if I forward the port to the DVR that i needed, ie 80 for web client or 6100 for desktop client, will that forward through?Or do I set it to Router Mode and use the Tilgen to assign the ips.
On the Tilgen I also have an option for a DHCP relay or to turn off DHCP.
For clarification here is the setup chain Broadband/DSL Line>>Tilgen Modem>>(LANPort1)Tilgen Router(LAN Port2)>>(WAN) Linksys(LANPort1)>>DVR/Computers Found this walkthrough on setting the WRT54G into a Switch. If I did this, in theory the VOOD would assign those computers/dvr connected downstream via the WRT54G a static ip from my range set on the router. Then in theory I would not need to port forward port 80 since the DVR would be on its own public IP.?
We recently moved 8 pc's from a room where they each had port on the switch to a room where there is only one port for all of them. I setup a DLINK DIR632 Router in there and they connect thru the one port thru the switch to the gateway which gets them out to the internet.The problems is I need to be able to remote desktop into these 8 PC's and I need them to be able to print to the network printer. I am using a Linksys WRT54G Broadband router as the gateway connecting the switch to the internet. The DLINK's dhcp server is on for the 8 PC's. The Linksys' dhcp server shows the DLINK as IP 192.168.1.19 on the network.I know I have to use advanced routing settings but I'm not sure about how what to make the subnet mask and IP's on both routers. I believe I need to turn off the dhcp server on the DLINK and have the Linksys' dhcp server serve all of the PC's but I'm not sure if thats the best way or if its possible.. I don't want to hack out fix only to find it breaks 3 days later.I used to do this stuff all day long in the 90's but its been a while and to me its like calculus.
I have a dell powerconnect 2848 switch and setting up a vlan 3 an make port 1 mngt, port 48 uplink to layer 3 switch and tag vlan 1 and 3 to port 48 with cli commands for this setup. and also to untag ports 2-10 for computers
I want to setup a static ip address for a h.264 network dvr ,however my desktop computer is out of order, that is connected direct to router,is it possible to use my wireless laptop to setup the router,or will I have to connect the eithernet cable to the laptop.
Currently in my office have a TPlink wireless router (WR1043N), and Dlink 615 router.Below is my office's network organization.Internet-->TPLinkRouter(192.168.2.0)-->DlinkRouter(192.168.0.0)We want to host a demo website but we are afraid our network being attacked. So we wish to implement a DMZ network to hide our internal network from outside. My question is can i setup a dmz network with the above capabilities by using home routers?
I have a Dell switch setup with 2 Vlan's. Vlan 1 is to the network. Vlan 20 is going to be for wireless access to the internet. How do I configure the switch/router so that Vlan 20 only connects to the internet and not the network? I will later want to have a 2nd SSID that I want to connect to both the internet and network.
I recently acquired a used SRW2016 in perfect working order (I checked it) and then made the mistake of trying to update the software image. Since then I cannot get any image to boot and cannot install a new one despite many attempts with XMODEM.The switch is hardware version 1.1 with Boot image "BOOT Software Version 1.0.0.03 Built 08-Jun-2004 09:48:10" I've tried installing a new boot image via XMODEM: [code]
Im trying to recover the password from my stacked switchs(doing procedure on master switch),im following a guide i have read in this forum("SRW248G4 V1.1 unable to reset password"), at console terminal have chosen "password Recovery" it prompts the "current password will be ignored" and then i hit "Escape" the switch start loading de configuration, at this point i attempt to login from telnet or http but the login fails. Here is the password/username combo im using (admin/blank ; admin/admin). Is it possible to restore admin password or should i just hardware reset the switchs?
I am following instructions I found to set up my wirelss network, but am having trouble configuring my router. I'm specifically at a standstill, because I can't connect to http://192.168.1.1. I pinged the router and got a response and went to run/ip config to confirm I have the right URL for the router, but still not able to get to the URL.
We are setting up a new office and I am trying to get RADIUS setup for authentication to my switches and routers. Currently I am working on a 3750 running IOS 15 and getting hung on what I think on something small. I have attached my Microsoft NPS Network Policy. Below is my IOS config:
aaa group server radius corp-radius server 10.15.10.20 auth-port 1812 acct-port 1813 ! aaa authentication login default group corp-radius local aaa authentication login radius-localfallback group corp-radius enable aaa authorization exec default group radius
My modem is an Arris Model TM502GI don't remember how to set it up. That is what cable goes where & is there anything to do on the PC With WiFi for it to connect with my router?I am 70 years old with a limited knowledge of computer and other electronic gadgets.