I had this small internet cafe with 15 units pc. and browsing the web is not that stable. i have to unplug the internet modem everytime i can't connect to the internet.I think it has something to do with the settings that was in the router since it was just configured by a tech guy which i think not 100% sure of what he did, though it can connect to net for sometime but most of the time it is down.
View 5 RepliesHow to set up more than 40 pc's with out internet connection using linksys switch.
View 3 Replies View RelatedMy router is a Dlink Model DI-624
My modem is an Arris Model TM502GI don't remember how to set it up. That is what cable goes where & is there anything to do on the PC With WiFi for it to connect with my router?I am 70 years old with a limited knowledge of computer and other electronic gadgets.
I have been putting up with rubbish wireless signal down one end of my house now for quite some time. So I thought I have a spare wireless router and I could put it down there but I am sure ts not as easy as just plugging it and away you go.
Network Setup
Router 1 is a D-Link DIR-655
Router 2 is a D-Link DI-524
I need to know how to setup Router 2 so it basically become just a wireless access point
What are procedures to deactivate di-604+di-704 routers+make the repeaters,connecting each of them,in a wired fashion,to my Belkin wireless N router?
View 1 Replies View Relatedmodem
........ |
........ |
----switch-----
|................ |
|................ |
Router 1.... Router 2
|..................... |
|..................... |
Computer 1.....Computer 2
......................Computer 3 Router 1 points to a VPNRouter 2 access to the internetComputer 3 needs to access router 1 (VPN). Both Computer 2 and 3 are in a different room than computer 1, and router 1. Computer 2 is networked via cat5e to router 2.Is is possible to have Computer 2 and 3 share the cat5e, yet access different routers?
I have a cricket broadband modem to connect to the internet. I want to use my Dlink di-524 router to share that internet connection with the other computers on my network. How do I do this?
View 1 Replies View RelatedMy d-linl router was not working and I pushed reset button and it went back to factory setting. I don't know what the factory setting is and I want to put my own password but don't know how. I have Window 7?
View 1 Replies View RelatedLost access to internet on all wired comupters. Can still connect to router via wired computers but not beyond. Wired PS 3 and wireless still connect to internetUsing a D-link dir 655 router
View 2 Replies View RelatedAt 9:15 each night my DLINK router drops the signal.I've tried to unplug it but that doesn't work but it is working again each morning. I can plug directly into the cable modem and it works so I assume it is fine.Is there a time setting on the router?
View 1 Replies View RelatedThe router's software was installed on our desktop years ago and now, the desktop is quite old and we have to sell it. I need to know if we need to reinstall the software again in probably in one of the laptops at home.
View 2 Replies View RelatedIs it possible to change the firmware on my dl2670 router so i may use my 3g usb stick, as the router does have usb ports?
View 1 Replies View Relatedwhy do my DHCP for DLINK DSL-2540T always keep disabled although i already set for enabled one day before?
View 1 Replies View RelatedI've had my network up and running for several years with no issues. Last week I upgraded my router to a Dlink 826L and now anything connected to my downstream Dlink DSS16+ can't be accessed.
View 3 Replies View RelatedWe had to send our Canon Pixma MP830 all in one printer in for repairs, and we have an mx870 loaner. The MP830 was connected directly to the desktop computer and to a lap top in another room via a dlink router. But we do not know how to get the lap top to recognize the MX870. We tried adding it and entered the name Canon Pixma M870, and the program does not accept the name.
View 1 Replies View RelatedHow can i implement networking in my THREE floor office by using routers and switches?
View 1 Replies View RelatedAlthough we have a moderately wired house with cat6 cables runs in many of the rooms that all end in the basement, I am currently having trouble since I cat stream audio and video files from my desktop in the den to the netbook and receiver in the family room. All computers are hooked up by cable.I have tried a friends advice to plug in the exact IP address of the desktop (and vice versa on the netbook) but still the netbook cat find the desktop nor can the desktop find the netbook. I have tried home sharing in Windows 7 to no avail as I have been prompted to initiate a home network both on the netbook and the desktop when I think it is suppose to be initiated on one machine and same home network joined by the other.DSL Modem --> Linksys WRTGL router running Tomato --> switch -->various rooms (cont.)Family room (one of the various rooms) has a Buffalo WZR-HP-G300NH AirStation (with one USB port) --> 1) netbook and 2) Denon AVR receiver (with network capabilities)I have a switch in the den and the desktop and laptop computers can read off each other through folder/drive sharing even with Kaspersky Internet Security running in the background so I'm sure it's not Kaspersky meddling with my network sharing. If both are on the wireless network, the netbook can access the desktop and vice versa.Is it possible for the netbook to read off the desktop based on my current set up? I can't bring the desktop down as we use them in the den and will not have room for it in the family room. I am not inclined to purchase a stand-alone HTPC at the moment if there is a network sharing
View 2 Replies View RelatedI want to setup an home network with a wireless router and use multiple switches for wired connections through out my home. I currently have an Airport extreme hooked up to a cable modem and a leviton gateway hooked up to the Airport. The 2 computers connected to the Leviton are on a windows 7 homegroup and share fine, but won't share or discover any wireless device connected to Airport. My main goal is to have a wireless/wired network with all computers sharing information with each other. I want 2-3 wired switches/gateways with a min of 2 devices connected to each, connected to my wireless router whiich is connected to cable modem.
View 3 Replies View RelatedI have 4 desktops cat5 to Dlink DIR 615 router. All work fine. Any wireless clients, laptop or netbooks, see the desktop computers for a while then disconnect somehow. All machines can see the Internet through the router at all times. The desktops disappear from the laptop/netbooks but the wireless machines can be seen from the desktop computers but clicking on them gets 'Access Denied' message after a wait.3 desktops = XP, 1 98SE. All laptop/netbooks = XP
View 2 Replies View RelatedI have 3 different office location and I need to set up a LAN so that all three are connected and can share info?
View 1 Replies View RelatedAt my company, we lease 3 static public IP addresses from 1 ISP. We want to have 3 separate networks that each use one of the IP addresses. Network 1 is the computer network, network 2 is the VOIP network, and network 3 is the security camera network. I am trying to determine the best way to do this. I have come up with 2 solutions in my head, but I'm not sure if they will work or not. I would like to get some input. Solution 1:Solution 1 looks something like this. Fiber box -> Router-> 3 switches. There would be one WAN input on the router, that would have a static route to 3 different LAN ports. For example, address 24.244.208.101 would be assigned to LAN port 1, 24.244.208.102 would be assigned to LAN port 2, and 24.244.208.103 would be assigned to LAN port 3 (by assigned, I mean have a static route to it). Is there some type of router that is capable of doing this? Solution 2:Solution 2 looks something like this. Fiber box -> Switch -> 3 Routers. The ethernet cable would run from the Fiber Box to a switch, and then 3 routers would be plugged into the switch. Each router would have the Static information configured in them. Would both of these methods work? If so, which would be the best way to go?
View 2 Replies View RelatedWe are in the process of switching to a new internet provider in our office and have run into some problems. Our old setup was with AT&T, where they provided a managed router which linked to our internal switch and also provided NAT to the internal IP of our email server.Our new setup right now is just the internet coming in through a cable connected to a switch, we were told we needed to provide our own router. Someone donated a Cisco 2900.What should our proper set-up be? Should the internet come in directly to the router and then to our switch, or should it go to the switch they provided, then the router, and then our switch?Also, there seems to be some confusion about whether or not we need anything else to get the internet to work. There are slots for network cards in the router. Does it come with at least one built in we can use, or do we need to provide one?
View 1 Replies View RelatedI did RECOVERY on my computer. Its a Compac Windows XP Home edition. This computer runs off of my main computer by a router & adapter. My router & adaptor are showing green but the Internet is showing red. Its becuz my high speed Internat service is ATT.my.yahoo.com. which comes through IE. On my newer computer all is fine. My IE works good & all is working. but my IE on my older one which runs with the router wont set up.
View 1 Replies View RelatedI Have a Computer Ready for setup as a Server in the LAN Connection:
Windows 7 Professional.
Another 2 Computers for LAN Connection:
1st Computer is a Windows 7 Professional (Connect as LAN)
2nd Computer is also Windows 7 Professional (Must connect using a Wifi D-Link)
Another 2 Computer for LAN Connection:
Windows XP: Must Connect Using LAN port.
1 Computer:
Windows 7 Home Edition: Must Connect Using LAN port
2 Laptops:
1st Laptop is using Windows 7 Ultimate.
2nd Laptop is a Vista.
How to Connect these Computers to the above mentioned computer ready for setup as as Server?
I have VOIP and was provided a modem, a Tilgen Router (Vood 452_A). I also currently have a Linksys WRT54G router. I also have a home surveillance system with a DVR that can be accessed via the net. I am trying to allow the ports to open so that traffic can navigate down to the DVR.My IPs:My VOIP has provided me with 6 static IP addresses. For sake of this issue they are:
67.xx.xxx.153, through .158My subnetmask is set to:
255.255.255.248My Settings:
The Modem is connected to world. To the modem I have the Tilgen Router connected. The Tilgen is set with an ip of .153 and the subnetmask listed above. DHCP is turned on and has IP range set for .154-.158. It is set in Bridge Mode with NAT and Firewall turned off. To that I have the WRTG54G router connected and assigned the router an Static IP of .154.. The cable is going into the Linksys WAN port.From a computer connected to a LAN port on the WRT54G, I see my public IP as .154, currently my internal IP is 192.168.1.15 so I believe I have to assign one of my Static IPs to this PC, however when I try to connect to the Linksys Router (.154) from the outside web, I am get a time out error. (also from a ping test.) My thoughts are to assign the Linksys to DHCP and use a range of .155-.158 to give each lan item a static IP. My question is will this work? Will each item in the network have its own IP and if I forward the port to the DVR that i needed, ie 80 for web client or 6100 for desktop client, will that forward through?Or do I set it to Router Mode and use the Tilgen to assign the ips.
On the Tilgen I also have an option for a DHCP relay or to turn off DHCP.
For clarification here is the setup chain
Broadband/DSL Line>>Tilgen Modem>>(LANPort1)Tilgen Router(LAN Port2)>>(WAN) Linksys(LANPort1)>>DVR/Computers
Found this walkthrough on setting the WRT54G into a Switch. If I did this, in theory the VOOD would assign those computers/dvr connected downstream via the WRT54G a static ip from my range set on the router. Then in theory I would not need to port forward port 80 since the DVR would be on its own public IP.?
how to open the tp-link interface setup for my TD-W896ON? i have a user and a password but where do i add them ??
View 1 Replies View RelatedWe recently moved 8 pc's from a room where they each had port on the switch to a room where there is only one port for all of them. I setup a DLINK DIR632 Router in there and they connect thru the one port thru the switch to the gateway which gets them out to the internet.The problems is I need to be able to remote desktop into these 8 PC's and I need them to be able to print to the network printer. I am using a Linksys WRT54G Broadband router as the gateway connecting the switch to the internet. The DLINK's dhcp server is on for the 8 PC's. The Linksys' dhcp server shows the DLINK as IP 192.168.1.19 on the network.I know I have to use advanced routing settings but I'm not sure about how what to make the subnet mask and IP's on both routers. I believe I need to turn off the dhcp server on the DLINK and have the Linksys' dhcp server serve all of the PC's but I'm not sure if thats the best way or if its possible.. I don't want to hack out fix only to find it breaks 3 days later.I used to do this stuff all day long in the 90's but its been a while and to me its like calculus.
View 13 Replies View RelatedI have a dell powerconnect 2848 switch and setting up a vlan 3 an make port 1 mngt, port 48 uplink to layer 3 switch and tag vlan 1 and 3 to port 48 with cli commands for this setup. and also to untag ports 2-10 for computers
View 1 Replies View RelatedI want to setup a static ip address for a h.264 network dvr ,however my desktop computer is out of order, that is connected direct to router,is it possible to use my wireless laptop to setup the router,or will I have to connect the eithernet cable to the laptop.
View 4 Replies View RelatedThe router was working fine when it was setup but was disconnected for a short while. There is now no recognition of the router and the install cd was misplaced...
View 2 Replies View RelatedCurrently in my office have a TPlink wireless router (WR1043N), and Dlink 615 router.Below is my office's network organization.Internet-->TPLinkRouter(192.168.2.0)-->DlinkRouter(192.168.0.0)We want to host a demo website but we are afraid our network being attacked. So we wish to implement a DMZ network to hide our internal network from outside. My question is can i setup a dmz network with the above capabilities by using home routers?
View 5 Replies View RelatedI have a Hawking 300N and I have misplaced my disk and I neing walked through this to have it set back up. I hooked it all up correctly and it says no internet connection
View 1 Replies View RelatedI have a Dell switch setup with 2 Vlan's. Vlan 1 is to the network. Vlan 20 is going to be for wireless access to the internet. How do I configure the switch/router so that Vlan 20 only connects to the internet and not the network? I will later want to have a 2nd SSID that I want to connect to both the internet and network.
View 5 Replies View Related