We had to send our Canon Pixma MP830 all in one printer in for repairs, and we have an mx870 loaner. The MP830 was connected directly to the desktop computer and to a lap top in another room via a dlink router. But we do not know how to get the lap top to recognize the MX870. We tried adding it and entered the name Canon Pixma M870, and the program does not accept the name.
View 1 Replies
I currently have Canon MX870 pixma printer - it is wifi enabled. A few weeks ago it went offline and I was able to reconnect it by entering the "access point" and password in printer control panel. It has once again gone offline however the printer cannot locate the access point by searching and when entered manually returns a message that it cannot locate the access point as entered. I am having the same problem with my TV which is also wireless connected, i.e., the TV is not connected to the internet and I cannot locate the network name (access point) in the setup menu on the TV. I had also previously reconnected the TV by entering the network name manually.
I tried looking in the router - Linksys Wireless-G 2.4 but cannot figure out where this information should be located. There is a setup tab in the router administration and both the Host name and the Domain name are blank. The router admin page states that: Host Name : Enter the host name provided by your ISP. Domain Name : Enter the domain name provided by your ISP. The wireless tab states: Status: SES Inactive. Does this mean anything?
Computer is a Dell Inspiron 620 running Windows 7 Home Premium
I have just had built a custom system and I purchased a new Canon Pixma 5220. I have the printer recognizing the access point, but it will not connect to the access point.
View 1 Replies View RelatedMy hp computer says I have succesfullyadded my printer, but when my printer page says it is not responding and consequently not allowing me to print.
View 1 Replies View RelatedI've had my network up and running for several years with no issues. Last week I upgraded my router to a Dlink 826L and now anything connected to my downstream Dlink DSS16+ can't be accessed.
View 3 Replies View RelatedBeen on the phone with Canon and they seem sure its the router. Linksys guy saying it was file sharing turned off. It was not..... I can print when I'm hooked in with an ethernet cable but not when I am on wireless laptop. Any setting I need to check in the E3000?
View 9 Replies View RelatedI have recently updated linksys ea4500 router with smart Wi-Fi firmware and installed USB printer with cisco usb software .on my laptop with windows xp on Wi-Fi it is working fine but on other laptop with windows 8 on wifi it is keep on connecting and disconnecting in status bar it shows unexpected disconnection.i want to use this printer from both laptops on wireless when ever needed
View 1 Replies View RelatedI just bought a canon pixmaMG6120 wireless printer...hooked it up to our wireless network (via a netgear wg624v3 wireless router). pritner recognizes the network, can sign into the network and has an IP in they systems setting. i can print to it via my iphone and ipad (all on the same wireless network).my HP dv6 laptop doesnt recognize a printer is on the network though. i've tried using the included cd, tried doing it via IP address, tried taking down all the firewalls, and nothing seems to work.
View 4 Replies View RelatedMy router is a Dlink Model DI-624
My modem is an Arris Model TM502GI don't remember how to set it up. That is what cable goes where & is there anything to do on the PC With WiFi for it to connect with my router?I am 70 years old with a limited knowledge of computer and other electronic gadgets.
I can't seem to get my Canon MG5220 Wireless Printer to connect to my Belkin N150 wireless router. The printer sees the belkin wireless router network name but cannot connect to it( after entering the correct security key). It worked fine with a previous wireless router. My desktop PC is connected to the belkin router via direct ethernet, and I want to be able to access my wireless printer which is located in another room from my PC. I think I remember reading that the canon mg5220 may not support WPA2 security, but Its only a year old and would prefer not to regonfigure my router's security setting. how I can get this printer to connect to my router? Any other ways to access this printer from my PC which is connected to LAN via ethernet?
View 1 Replies View RelatedMy d-linl router was not working and I pushed reset button and it went back to factory setting. I don't know what the factory setting is and I want to put my own password but don't know how. I have Window 7?
View 1 Replies View RelatedAt 9:15 each night my DLINK router drops the signal.I've tried to unplug it but that doesn't work but it is working again each morning. I can plug directly into the cable modem and it works so I assume it is fine.Is there a time setting on the router?
View 1 Replies View RelatedThe router's software was installed on our desktop years ago and now, the desktop is quite old and we have to sell it. I need to know if we need to reinstall the software again in probably in one of the laptops at home.
View 2 Replies View RelatedI have issue with connectivity 3750G with Dlink Switch, it cannot connect to non-cisco switch with fiber , But CISCO to CISCO switch it shows connectivity. My question is that is there any configuration on Cisco 3750G switch to connect with non-cisco switch through fiber (SFP) ?
View 2 Replies View RelatedI am trying to extend my broadband signal out from the house to a rumpus room.My current setup does not give a signal that far.. or at least it is poor with 1 mbps speed.To cable anything other than my moden to router A is not an option. Router A to Router B and then on to the computers needs to be wireless,My modem is currently connected to router A (Dlink dl624) but how do I get router B (dlink dir635) to talk to router A and then relay my broadbad to my computer out in the rumpus room and also inside the house when I am there.
View 2 Replies View RelatedWhat are procedures to deactivate di-604+di-704 routers+make the repeaters,connecting each of them,in a wired fashion,to my Belkin wireless N router?
View 1 Replies View RelatedI have 4 desktops cat5 to Dlink DIR 615 router. All work fine. Any wireless clients, laptop or netbooks, see the desktop computers for a while then disconnect somehow. All machines can see the Internet through the router at all times. The desktops disappear from the laptop/netbooks but the wireless machines can be seen from the desktop computers but clicking on them gets 'Access Denied' message after a wait.3 desktops = XP, 1 98SE. All laptop/netbooks = XP
View 2 Replies View RelatedI have a cricket broadband modem to connect to the internet. I want to use my Dlink di-524 router to share that internet connection with the other computers on my network. How do I do this?
View 1 Replies View RelatedI had this small internet cafe with 15 units pc. and browsing the web is not that stable. i have to unplug the internet modem everytime i can't connect to the internet.I think it has something to do with the settings that was in the router since it was just configured by a tech guy which i think not 100% sure of what he did, though it can connect to net for sometime but most of the time it is down.
View 5 Replies View RelatedLost access to internet on all wired comupters. Can still connect to router via wired computers but not beyond. Wired PS 3 and wireless still connect to internetUsing a D-link dir 655 router
View 2 Replies View RelatedIs it possible to change the firmware on my dl2670 router so i may use my 3g usb stick, as the router does have usb ports?
View 1 Replies View Relatedwhy do my DHCP for DLINK DSL-2540T always keep disabled although i already set for enabled one day before?
View 1 Replies View RelatedHow to connect 2 cisco modem in 1 3com router.
View 6 Replies View RelatedI just got a DSL Modem router (DSL 2750U) which has DSL input for internetconnectivity.My internet service provider provides RJ45 Cable which needs LAN input socket on a router for internet connectivity. How do I connect?
View 4 Replies View RelatedI am trying to connect a Netgear wirless router to my cable modem. I have followed the instructions on the set up wizard but it fails to get a connection with the IP and DNS info I provide.I got the IP address info by connecting intially direct from the modem to the PC and then went to Run CMD and type ipconfig /all. I then started the set up wizard and followed the instructions, turning things on in specific order etc. After input the IP and DNS info it reports an error and tells me to check the address information is correct.My internet is a static IP connection (so it tells me and the IP information doesn't change).
View 3 Replies View RelatedAfter a power failure nothing could connect to the internet anymore. I called MTS (ISP provider) and they had me change some setup on my PC. Now my PC connects to the internet, but nothing else will connect (X Box, WII, iPods, Laptop). They were connected wireless before the power outage through my router. MTS said they are only responsible for ensuring their model works, not routers.I have checked some router settings. It is set for DHCP with 50 users.
View 15 Replies View RelatedI have HP laserjet 4000 tn. Had an old router and upgraded to a new wireless router, when connecting it to the new router, the port I connect to has the amber light come on. I have reset to factory setting thinking it would reset and capture a new ip address. still giving me problems. try connecting it to my macbook pro and cannot get a "fix" on the printer either. I know it has to do with the configuration of the printer.
View 3 Replies View RelatedA newer router that I got from a friend, a CISCO Linksys WRT310N, is not connecting to my XP computer via a CAT5e cable. It willconnect for about 5 to15 mins, then lose connectivity. Ihaven't tried with a faster CAT6, since my dog chewed through my other one,and I have yet to get a new one. I used an older NETGEAR B/G router and it worked fine.
View 10 Replies View Relatedi ahve a dlink dir 615 B2 router and it wont connect to the internet. on day it was fine and working, the next day the internet led wouldn't change from the red light to the green light.i have tried resetting it about 60 times, while the laptop was on/off, while it was plugged it, while it was without power, while the internet cable was in, while it wasn't, while it was shut down and i reset it and the i pluged it in while resetting it...i dont know what else to do!! short of smashing the bejesus out of it. The internet works fine when i connect the cable directly to the laptop, I don;t have a cable modem or anything, just a plain old cable from the street to my house.
View 3 Replies View Relatedhow can i connect a Net gear DGN2200 wireless modem router to a D link DGL4500 wireless router ??
View 1 Replies View RelatedI have just purchased a new ASUS Laptop for my wife.We are currently running two destop computers on a D LinK Router. How do I go about including the new computer on the network wirelessly?What do I need to purchase to make the transition easiest? The two desktops are running Windows XP Professional, the new system is Windows 7.
View 4 Replies View RelatedI am replacing old D-Link DI-714P+ router with E1200.The old configuration was a printer connecting to D-Link router, and allow for wireless printing. Therefore, may I know how do I configure E1200 so that I still can print wirelessly, while connected to E1200 network.Assuming the printer still connected to Dlink router, can we print to E1200 then bridge to Dlink ?
View 2 Replies View RelatedI have a home network that uses a DLINK DIR-655 router. All of my devices ( a mix of wireless and wired) except one--a windows xp SP 3 desktop that stopped working yesterday. Some viruses, and adware were detected and it has not worked since then. What I have done.
View 11 Replies View Related
