Lost access to internet on all wired comupters. Can still connect to router via wired computers but not beyond. Wired PS 3 and wireless still connect to internetUsing a D-link dir 655 router
View 2 RepliesI have a cricket broadband modem to connect to the internet. I want to use my Dlink di-524 router to share that internet connection with the other computers on my network. How do I do this?
View 1 Replies View Relatedthe modem is open.the router also is open but dont have internet access.
View 1 Replies View RelatedWhat are procedures to deactivate di-604+di-704 routers+make the repeaters,connecting each of them,in a wired fashion,to my Belkin wireless N router?
View 1 Replies View RelatedI had this small internet cafe with 15 units pc. and browsing the web is not that stable. i have to unplug the internet modem everytime i can't connect to the internet.I think it has something to do with the settings that was in the router since it was just configured by a tech guy which i think not 100% sure of what he did, though it can connect to net for sometime but most of the time it is down.
View 5 Replies View RelatedMy d-linl router was not working and I pushed reset button and it went back to factory setting. I don't know what the factory setting is and I want to put my own password but don't know how. I have Window 7?
View 1 Replies View RelatedAt 9:15 each night my DLINK router drops the signal.I've tried to unplug it but that doesn't work but it is working again each morning. I can plug directly into the cable modem and it works so I assume it is fine.Is there a time setting on the router?
View 1 Replies View RelatedThe router's software was installed on our desktop years ago and now, the desktop is quite old and we have to sell it. I need to know if we need to reinstall the software again in probably in one of the laptops at home.
View 2 Replies View RelatedIs it possible to change the firmware on my dl2670 router so i may use my 3g usb stick, as the router does have usb ports?
View 1 Replies View Relatedwhy do my DHCP for DLINK DSL-2540T always keep disabled although i already set for enabled one day before?
View 1 Replies View RelatedI've had my network up and running for several years with no issues. Last week I upgraded my router to a Dlink 826L and now anything connected to my downstream Dlink DSS16+ can't be accessed.
View 3 Replies View RelatedWe had to send our Canon Pixma MP830 all in one printer in for repairs, and we have an mx870 loaner. The MP830 was connected directly to the desktop computer and to a lap top in another room via a dlink router. But we do not know how to get the lap top to recognize the MX870. We tried adding it and entered the name Canon Pixma M870, and the program does not accept the name.
View 1 Replies View RelatedI lost my router 192.168.1.1 password and how to recover?
View 3 Replies View RelatedI have tried to reset linksys router and tried to use the IP address with an error message. We need to add another laptop to our network
View 1 Replies View RelatedMy router is a Dlink Model DI-624
My modem is an Arris Model TM502GI don't remember how to set it up. That is what cable goes where & is there anything to do on the PC With WiFi for it to connect with my router?I am 70 years old with a limited knowledge of computer and other electronic gadgets.
I have a wireless router that was named and all the wireless equipment (laptop, ipod, phones) was connecting easily with no problems. Everything is saying "unable to connect". I have no clue what she did but she said her laptop asked her for the 8 number code from the router and she entered it.
View 1 Replies View Relatedlost my password-can't connect my new nook to my network.
View 1 Replies View Relatedi tried to change my nat type to open, on my Netgear WNR2000v1.i connected throught typing my routers ip. (192.168.1.1)i watched a utube video, where someone told me that i had to changed something in the basic section to 2, instead of auto.now i cant connect to my router. ive tried with multiple pc's.
View 5 Replies View RelatedI have been putting up with rubbish wireless signal down one end of my house now for quite some time. So I thought I have a spare wireless router and I could put it down there but I am sure ts not as easy as just plugging it and away you go.
Network Setup
Router 1 is a D-Link DIR-655
Router 2 is a D-Link DI-524
I need to know how to setup Router 2 so it basically become just a wireless access point
I have 4 desktops cat5 to Dlink DIR 615 router. All work fine. Any wireless clients, laptop or netbooks, see the desktop computers for a while then disconnect somehow. All machines can see the Internet through the router at all times. The desktops disappear from the laptop/netbooks but the wireless machines can be seen from the desktop computers but clicking on them gets 'Access Denied' message after a wait.3 desktops = XP, 1 98SE. All laptop/netbooks = XP
View 2 Replies View RelatedI am trying to set up two routers so that I can offer free wireless connectivity via three AP's in three adjoining rooms on a first floor and secured wireless and wired network connectivity in upstairs offices. The setup is like this:
Verizon DSL connectivity..static IP
The gateway modem/router is a Verizon DLink DSL 2750B with three ports connecting to three wired Access Points in three first floor adjoining rooms, and the 4th port connecting to a Cisco E1200 (wireless and ethernet router) located next to the Verizon Dlink. I would like the Verizon DLink to give open wireless connectivity via the access points and also connect to the adjacent E1200 router.
I would like the Cisco E1200 to offer secured wireless and ethernet connectivity to the upstairs offices. (connecterd to the Cisco E1200 is a 24 port Netgear switch.)I have spent considerable time talking with Verizon and Cisco/Linksys but have not been successful in just how to set this up.A former tech actually did have this setup but for what ever reason the settings were reset to factory defaults with no written record as to the necessary settings.
Looking for a SOHO device that could accomplish not only to connect people from home to Internet, but also to let me remotely access my work stuff (from my home office), RV180W sounded great and really cost effective. I could connect to Internet, FROM Internet, separate home, work and guest VLANs, all in just one device... sounded just GREAT! Bought one but (unfortunately) I have to say I'm quite disappointed with its performance, outnumbered errors (how many!) and continuous lost of Internet connectivity (can't stay a full day without one).I've searched a lot (not only here) and tried many things, listing some:
- Upgrading firmware (now v1.0.2.6): done several times, once with nothing connected to the router besides a local wired laptop, to ensure integrity
- Resetting to factory defaults and performing a "clean configuration", from scratch (done several times)
- Disabling Firewall functions (once all of them)
- Checking the real need of every option and making sure I had just the ones I needed configured
I have (in a very "consistent" way) the following problems:
- Poor performance (it's clearly much better when I directly connect to the cable modem's WiFi OR to another router connected to this cable modem). I could say that it seems to have 50% of the performance I had with my CISCO/Linksys E4200 and Netgear "elder" routers.
- Persistent disconnections / resets: Sometimes it happens only with wireless, sometimes it looses the "Internet forwarding capability", retaining the local wireless connection (to other devices), sometimes it seems to make a full reboot (including a new DHCP request to cable modem). In a day this happens several times, I'd say from 3 to 15 times, depending on the day (couldn't figure out why).
CPU utilization is always shown as being 100%, what sounds amazing, because:
- There are usually just 4 wired connections (3 storage devices + 1 Desktop) and at most 5 wireless connections (including my laptop connected to the main VLAN and 3 Android devices and 1 "guest" laptop connected to GUEST VLAN)
- The utilization % remains when I have jut one laptop performing Internet browsing and nothing more
- VPN wasn't enabled yet (and it will be, as I want to remotely connect to my home office) [code] ......
i want to ask if i can link two routers while they are totally separated of each other over the internet to make a large LAN the two routers are TP link?
View 5 Replies View RelatedHow do i connect two internet routers to one IP address range?I currently have one broadband router connected on 172.16.0.3 subnet 255.255.0.0, I have a second line which is a copper ethernet EFM 2Mb line connected using a Cisco 1800 router configured on 172.16.0.254 subnet 255.255.255.0, no DHCP is configured on either router. the dhcp is provided by a windows 2003 server on our LAN which is also configured on the same LAN IP range. if i connect the Cisco router into the same switch as the broadband router my network devices stop working and dont respond.
If i check the broadband router it shows all the connections to it as having the same MAC address as the Cisco router?? if i disconnect the Cisco router everything returns back to normal and works perfectly.What I want to achieve is to be able to run both routers on the same LAN to provide internet access by configuring the pc's to route through a specific router. the DHCP I want to stay routed through my original broadband line. at the same time i want all pc's to access to the lan devices (ie. servers and printers) what the correct configuration would be for the two internet routers would be?
DLink DGS-3100 POE switches? I'm working for a place that has these and they are wanting to invest in a VOIP system. I've never seen these type of switches before, and would like some feed back before I roll out a 70+ phone VOIP system. They are managed switches but are all running un-managed at the moment.
They are also using a Fortigate 80cm Firewall/Router. I'm not familiar with this device either.
I'm missing layer 3 as I can't setup any VLan's with this equipment.
I have issue with connectivity 3750G with Dlink Switch, it cannot connect to non-cisco switch with fiber , But CISCO to CISCO switch it shows connectivity. My question is that is there any configuration on Cisco 3750G switch to connect with non-cisco switch through fiber (SFP) ?
View 2 Replies View Relatedwith a networking issue that I'm having with the 2nd computer I have trying to connect to the interntet via my Westell 7500 DSL router. I ran the diagnostic tool on the NIC to make sure it working correctly and it is, and so is the cable according the tools; I also verified that myself via unplugging/plugging the cable into the router and it detects eachMy other 2 computers work fine via the router.Here is the ipconfig info;Host Name:XXXXXXPrimary Dns Suffix: (blank)Node Type: HybridIP Routing Enabled: NoWINS Proxy Enabled: NoEthernet Adapter Local Area Connection:Connection-specific DNS suffix: (blank)Description: Intel(R) 82562V-2 10/100 Network ConnectionPhysical Address: 00-1D-09-8D-34-3BDHCP Enabled: Yes
View 3 Replies View RelatedSome day, then my internet jut died. then I got the router restarted(unplugged the electricity and plugged it back in) and it worked for like a day and then it died again. I restarted the router again Internet worked and then some hours later it died again.This problem only happens to me and not anyone else in the house.I'm connected from my pc with and ethernet cable to a switch/HUB where it's then connected to the router.
View 8 Replies View RelatedI use this oid to gather mac address: .1.3.6.1.2.1.17.4.3.1.1
This has worked on all of our cisco switches (3560,SG300, etc...). When an SG300-20 was updated to 1.2.7.76 the oid no longer exist.
snmpwalk -c public -v 2c switch .1.3.6.1.2.1.17.4.3.1.1
iso.3.6.1.2.1.17.4.3.1.1 = No Such Instance currently exists at this OID
Should I downgrade the switch back to 1.1.2.0?
The connection of the computer before is activating.. after how many days of using,it losses the internet connection.. what is the possible reason for this?
View 1 Replies View RelatedI have an ARRIS modem supplied by Comcast cable. I have an hp pavilion x1958 and want to run internet service to a secondary computer from the same modem. And I don't have money to buy a router. How can I do this the cheapest way?
View 3 Replies View RelatedI have a DVR system. Which is configure in DMZ on my firewall. DVR internal IP is 192.168.2.13 and external IP is 27.34.xxx.xx. when I am able to access DVR by using internal IP and it works fine while accessing from the internet it not work proper. Though it prompt for username and password also. After enter the login credential its getting blank. I am able to telnet External IP from internet on port 80.
View 1 Replies View RelatedI have a USB modem connection, and i want to share the connection with two computers and three wireless devices through a sky router. The system OS is Windows 7
View 4 Replies View Related