We have a dlink DIR 615 router that keeps dropping the internet connection. I checked with our internet provider about the connection and it is fine. The desktop has no internet issues just the wireless devices. We run a laptop, iPod, cell phone and tablet. Everything was fine until we added the phone and the tablet.
Yesterday we had a very brief power outage and until then everything worked fine. Small business that runs modem - router - switch. Since the power outage I can only get internet if I run straight into the modem. As soon as I run from the modem to any (tried 3 different ones) router I lose internet. I get a wireless signal on my router. I've reset the router to default settings. I've plugged in another router to the modem to check and I don't get anything from that router either (which was not plugged in during the power outage).
I have wireless internet with a cisco valet router. My problem is that yesterday when I turned on a laptop that I use only once a week or so, now shows the signal strength of the network but I can not gain access to it. The main error message I get when I troubleshoot is that the network connection has come unplugged.Yes, I have the wireless switch turned on, on the laptop. That was the first thing I checked. I uninstalled cisco software on the laptop and reinstalled it and the laptop will not connect to the network.
I have the latest flash installed. I am making use of all the options available to this router. USB drive set up as a file server, both radio bands have devices which attach. All wifi security is wpa2 with a complex key string. Also have pc’s attached to all lan ports. I also have all the wireless devices registered on the mac address filter for access set to enable/allow. I have a total of 9 mac address in the list. One lan device is on the DMZ. One address is reserved. Not sure what other details you need.Router is used for online gaming, video streaming, and typical internet browsing.
I connected the Router to the modem, and all the wired connected PCs were working perfectly.But then, i went to the setup page to configure the Wireless settings, and as soon I changed the SSID name, the connection internet connection droppedThe only way i had to fix this was by making a Hard Reset.after that, I also tryed changing values and settings from all the configuration tabs, and the wired connection was working properly, but as soon i changed any value from the Wireless tab, the internet connection dropped (even, in the diagnostics section, i could not do a ping to google. It says unknown host).
Earlier today I attempted to change the setting on my Westell 6100 modem such that it would simply bridge the connection to my Linksys WRT54GS router, basically involving setting the router to bridge only and turning DHCP off. Now I no longer get an internet connection through my router when previously the connection had worked perfectly fine before. I following the steps of cloning the MAC address to the router and have done the proper resetting steps (computer, them router, then modem) but I simply can't get an internet connection through my router. The process to set up simple bridging from the modem what supposed to end up with the internet light no longer turning on but the light turned back on following one of the resets.
Currently, I can connect to the internet through the modem just fine but I get nothing when I include the router. I'm not sure if there are some other settings I'm supposed to be changing as I can't seem to find anything past what I've already done when researching online. At this point I would just be happy reverting the settings I've changed but I don't know how to access the modem now that DHCP is off.Basically, I'd prefer to be able to get the router working with these new settings but if that proves too difficult (as I've heard it can be when trying to get Westell modems to work with Linksys routers) I'd like to learn how to access the modem and change the settings back to what they were (preferably in as simple terms as possible as I don't particularly understand what a lot of these settings/configurations do).(And a bit of an aside, but I had attempted to do this modem bridging to "fix" perceived internet speed problems. I've been averaging around 300Kbps download rates ever since I've had this internet connection from Verizon when the supposed download rates should be between 1MB and 1.3MB. Doing this modem bridging had been reported to fix some modem/router conflicts and improved connection speeds for some.)
Dlink Dir-657 keeps losing internet connection on wifi devices only . the connection remains to the router but no internet .if I disconnect the connection i am unable to reconnect to the router until i reboot it. My internet remains on my network cabled devices .I am running on an empty channel 3 , usually happens 20 to 60 minutes after the router is up . Dlink sent me a replacement refurbished one and this one is doing the same thing . I owned the original one for about 5 months with no problems at all ,no new electronics in the house and have not changed the placement of the router .
When I try to connect to the internet I get IE cannot dislay the webpage. All connections show that they are working fine. I did the repair option for my LAN, it states that it is working & shows that it's connected.I tried to sign into MSN & got no connection. I ran the repair option & got a DNS & Keyports warnings.I am running Windows XP on my home computer
My computer is part of domain.I have one LAN connection. IP address 188.8.131.52 ,subnet Mask 255.255.255.0, Default Gate Way 184.108.40.206Another is one internet connection through bluetooth PAN IP address 192.168.0.103, subnet Mask 255.255.255.0, Default Gate Way 192.168.0.1.Problem is when I connect to LAN, internet connection is lost. If I take out LAN cable or disable LAN, I get the internet connection. I want to keep both LAN connection and bluetooth PAN internet connection.I must keep LAN IP address without changing.
I was trying to browse the internet earlier, and I randomly just lost my internet connection. My homepage loaded up just fine, but then I tried to go to another site. It was taking a while to load. After about a minute a page finally came up that said "Server not found" (I use firefox). I can't get on any websites now and I can't get internet on any of my wireless devices either. When I right clicked my network icon on the toolbar and clicked on diagnose and repair it said "There may be a problem with the DNS. Windows attempted to find the well known host www.microsoft.com using dns. The server responded that the name was unknown." I have Windows Vista. Now I have no idea what I could have done. I didn't do anything out of the normal, just tried to go to a website that I frequently visit with no problems and this happened. This is what I get when I type ipconfig/all in cmd prompt. [code]
I dont have an internet connection through my computer. This one tells me error 106. I have 3 computers hooked through the same router. So, I know I have internet, as I am writing this now. But for some reason, that computer is now telling me I lost the internet connection. I have tried unplugging everything, restarting the computer, and nothing has worked. I dont know how to get the internet back on that computer.
Whenever I restart or boot my computer, it loses internet connection (Local Area Connection Unplugged). I need to unplug the cable connecting my pc to the modem and replug it until the green and orange light comes on on the area where I plug the cble to the pc w/c means that there is already internet connectionSystem:Win XP sp3 OSGigabyte S-series motherboard ma74gm-s2Amd Athlon X3 processorMotorola SURFboard SB5101U/SB5101N Cable modem
Implement the procedures required so that machine 1 and machine 2 can communicate statically with one another. Outline the TCP/IP settings to be used on each of the machines and set this machine up accordingly.
I followed this guide [TUT] Setting a static internal IP (Windows and Linux)but what has happened is that now the two machines can't connect to the internet.
I have just turned my PC on to find that i have lost connection to the internet through my desktop PC. I am using the wired connection to my router, and i also have my xbox connected to the router which is working ok too. My laptop also works when connecting to the router both wired and wirelesly.
My network adaptor on my desktop is a Nvidia nForce, i have tried updating the driver on this to no avail. Next i tried to ping the router but i get PING Transmit faild, error code 1231. I ran IPCONFIG /all and found that i had no default gateway set, and also it was saying that the ethernet adaptor was : Media Unoperational, but since i rebooted both the pc and router the media unoperational tag has gone.
On the network and sharing page it shows i am connected to an unidenfied network but there is a cross through the internet. It also says the access and Connection for the unitentified network are Local only.
I no longer have internet access from my home network ONLY on my desktop computer. Everything was working fine as always - then while I was in my Network and Sharing Center, and clicked on my ethernet connection, 'Local Area Connection 3', I accidentally disabled it. No big deal I thought, so I re-enabled the connection. Except for some reason, my connection is all screwed up now. The name of this connection was and always has been 'dkm2' and now it just says 'Network', with no internet access. I have unplugged the cord and plugged it into this laptop and it immediately recognizes 'dkm2' and connects flawlessly, so I know the problem is on the desktop computer's end, and not the cable or router. I have tried reinstalling the ethernet adapter, as well as reinstalling/updating all drivers for it.The network diagnostic tool turns up with a message that says the connection between either my ethernet adapter or router and the Internet is broken. No matter what I seem to try, I can't get my connection to go back to it's normal 'dkm2' connection and stop giving me a generic, disconnected 'Network'. I can't figure out what could have changed. All that happened was the disabling and enabling of Local Area Connection 3.
Implement the procedures required so that machine 1 and machine 2 can communicate statically with one another. Outline the TCP/IP settings to be used on each of the machines and set this machine up accordingly. I followed this guide http:[URL]....tid=210 but what has happened is that now the two machines can't connect to the internet. How can I fix this?
Here is a links to the ipconfig/ all on the XP virtual machine http:[URL]....the default gate way here is the same as on my actual working machine.
I have PC System Windows XP home edition Version 2002 SP3 and I lost Internet access in the middle of downloading a new program. I have a Motorola modem and modem is connected to the Netgear router. When I turn my desktop PC on which is connected to the router it shows the local connection is connected, but the Bridge Network cable is unplugged I have no idea what that is and if I need it to be connected to the internet. I called the Comcast service and the lady assistant did not even know what the Bridge cable is and I do not know ether since. I do not know what I should do to get the connection back to the PC; another PC work just fine also is connected to the router.
We've had no problems with our Internet before but yesterday I could only get local access connection. Neither my iPhone, laptop or home computer cud get any further than local connection on wireless.I'v tried the classic turnin it off and on (the router) and I'v tried connection with a cable but still gettin the same connection level! The router is a netgear if that means anything!
I have an HP EliteBook 6930p with windows 7 installed and everything was working fine until i did a recent windows upgrade (might just be a coincidence) and i suddenly lost internet connection. My laptop picks up the router, shows full strength but i cannot connect to the internet wireless or Ethernet cable. I restored to a previous date and it worked fine, and all my other devices work fine (iPad, iPhone, other laptops). The trouble is when i connected to the internet again it up dated windows and i cant restore back to the original date anymore as it has gone from the list.
I am running Windows 7 - 64 bit on my laptop. I currently have Avast Internet Security installed and I have tried to uninstall the Avast software as I wish to change my antivirus software. I have tried uninstalling in safe mode using the Avast Clear utility. Unfortunately after using this utility the Avast program still remains on my hard drive in Program Files which I then have to delete manually. After doing so and restarting my computer I have no internet connection and the only way I can restore my internet connection is by copying the Avast program back into my Program Files.
I have lost my wireless internet connection it has been working perfectly, I phoned Sky and they say I will have to speak to dell to see where my internet has gone. I have a Studio 1745 Laptop. Is there a manual disable button on my laptop that I may have disabled by mistake.
I have a DELL inspiron N5110 laptop. I have 2 laptops at home including this one. However the Dell suddenly stopped connecting to our Sky broadband when it was previously connecting normally. The other devices including Iphones are fine! It says there is normal broadband connection, but then no internet connection! how to get back internet connection!
I have a Cisco ASA 5520 that we was working properly. I tried to create a VPN IPSEC to test but when I finished the wizard I lost the conection between the inside interface and outside. I use other interface for DMZ and other for printers network but this adapters are working properly. I have reviewed the NAT's and the ACL's but I don't see the problem?
I have delete the VPN IPSEC but it's still not working and I have the network down
I am trying to set up two routers so that I can offer free wireless connectivity via three AP's in three adjoining rooms on a first floor and secured wireless and wired network connectivity in upstairs offices. The setup is like this:
Verizon DSL connectivity..static IP
The gateway modem/router is a Verizon DLink DSL 2750B with three ports connecting to three wired Access Points in three first floor adjoining rooms, and the 4th port connecting to a Cisco E1200 (wireless and ethernet router) located next to the Verizon Dlink. I would like the Verizon DLink to give open wireless connectivity via the access points and also connect to the adjacent E1200 router.
I would like the Cisco E1200 to offer secured wireless and ethernet connectivity to the upstairs offices. (connecterd to the Cisco E1200 is a 24 port Netgear switch.)I have spent considerable time talking with Verizon and Cisco/Linksys but have not been successful in just how to set this up.A former tech actually did have this setup but for what ever reason the settings were reset to factory defaults with no written record as to the necessary settings.