Dell :: Canon Mx870 That Is Not Responding
Oct 24, 2011My hp computer says I have succesfullyadded my printer, but when my printer page says it is not responding and consequently not allowing me to print.
View 1 RepliesMy hp computer says I have succesfullyadded my printer, but when my printer page says it is not responding and consequently not allowing me to print.
View 1 RepliesI currently have Canon MX870 pixma printer - it is wifi enabled. A few weeks ago it went offline and I was able to reconnect it by entering the "access point" and password in printer control panel. It has once again gone offline however the printer cannot locate the access point by searching and when entered manually returns a message that it cannot locate the access point as entered. I am having the same problem with my TV which is also wireless connected, i.e., the TV is not connected to the internet and I cannot locate the network name (access point) in the setup menu on the TV. I had also previously reconnected the TV by entering the network name manually.
I tried looking in the router - Linksys Wireless-G 2.4 but cannot figure out where this information should be located. There is a setup tab in the router administration and both the Host name and the Domain name are blank. The router admin page states that: Host Name : Enter the host name provided by your ISP. Domain Name : Enter the domain name provided by your ISP. The wireless tab states: Status: SES Inactive. Does this mean anything?
Computer is a Dell Inspiron 620 running Windows 7 Home Premium
We had to send our Canon Pixma MP830 all in one printer in for repairs, and we have an mx870 loaner. The MP830 was connected directly to the desktop computer and to a lap top in another room via a dlink router. But we do not know how to get the lap top to recognize the MX870. We tried adding it and entered the name Canon Pixma M870, and the program does not accept the name.
View 1 Replies View RelatedHave a Canon MP495 (wirelessconnection) whiich worked until I changed internet provider, It was saying printer not respondingand now it's saying printer offline. It won't work with usb connection either. Tried reinstalling it but still nothing..
View 1 Replies View RelatedCanon MG5300 Windows 7 64x Home Premium
It was working fine and suddenly quit working. When trying to print, get the printer not responding notice. When scanning, it shows disconnected.
i have a Dell XPS 8500 with windows 8, Currently it's connected to the modem by ethernet cable Currently i have cable broadband which is fast normally occasionally it's slows for no reason i have done a diagnose test on the connection which came with the following results result of the test came out with the following which i am quoting exactly as it show's on my computer "your computer appears to be configured correctly, but the device or resource(DNS Servers) is not responding"by the way connecting to my router through wifi is not much of improvements?
View 7 Replies View RelatedI have a dell xps L502X with windows 8. My network adapter was replaced last month. My DHCP is enabled. My DNS Server reads 192.168.1.1 and it's a home/cable/DSL connection so from what I've read that's right. I've set my IPv4 and IPv6 to automatically detect the DNS server and IP address to use. I've tried to reconfigure the computer to the wireless router, but when I go to set up a new network no networks pop up even though many networks pop up for me to connect to on the right of my screen.
All of my other devices are connected and working fine. That was the background and what I've tried to fix for my problem. When I try to connect to my home network it says it's a limited connection meaning I have no Internet access. When I run the trouble shooter for the network, Internet connections, and network adapter the only one that has an issue is the network one and the issue is that the DNS server isn't responding.
i am unable to connect to the net in my laptop and laptop manifacturer is dell inspiron 1545 and error i am getting is DNS not responing.
View 2 Replies View Relatedmy Dell D505 will not respond with either enternet or usb ports to install a modemive tried hard wireing a westell and a netgear modem,also tried both with a usb adapter and the hardware wizzard will not find the modem so it will not finish the firmware install
View 5 Replies View RelatedI purchased the Dell XPS13 yesterday and took it home. I turned on the wireless and had internet access for a few minutes. Then it stopped working and the network diagnostic msg was "DNS Server not responding". All my other electronic devices at home are still working.
I took it back to the original computer store to get a technician to fix it. The internet worked in the store. However, after I took the laptop back home it only worked for the first few minutes and stopped working again.I've tried disabling the firewall.
How do i connect mac book to print wi fi to my canon printer
View 2 Replies View RelatedI am using cannon printerme connect it wirelessly to my laptop.
View 5 Replies View RelatedPrinter drivers for canon 2900?
View 1 Replies View RelatedI am trying to setup a network for my mother. They have 3 laptops and a Canon MX330 Printer. I am using an aris wireless modem, all pc's are connected wirelessly to the modem successfully. The printer only has a USB connection from it, so I purchased a Belkin router with wireless and USB.When I connect the USB to the belkin, the only way to print is by using one pc always connected. I want to be able to print from any laptop without having one remain "on." When I use any pc and try to add a printer it is NOT found on the network.
View 2 Replies View RelatedMy router recently packed up and have been issued a new one by SKY. All connected up but now I can't print wirelessly to my Canon MP600R. Message returned of 'A communication error has occured'. Am I supposed to have changed something when using a new router. I imagined it would just work.
View 3 Replies View RelatedAny way beside the standard router/printer rebooting, firewall disablity. I am able to connect to my first laptop on which I installed all the drivers on but when I try to add an additional windows 7 laptop
View 2 Replies View RelatedHave a Canon MG6120 wireless multifunction printer. I rarely print anything from my laptop, but wanted to do that today. What I get is an error message that the printer is offline -- which it isn't; it's on. I tried going thru the setup on the printer, re-entering the SSID, and it said it was connected. Still same error that it's offline.
About a month ago, I did change the name of my router, but it never cause a problem with printing from my desktop, which I can still do. It's just the laptop that gets the "offline" error.What do I need to do to make the laptop recognize that the printer is on?
My Canon MP495 3-in-1 inkjet XPS printer is connected through my mother's computer, and up until a few days ago I was able to print from it through our Home network. My mother can still print from it directly, so it is not a hardware issue. On my computer when I go to print, underneath the printer selection it says server offline. I have checked both computers and they are both on the Home network with all sharing options on. I can see her media and documents from my computer and she can see mine vise-versa. When I open the Network and Sharing Center and view the full network map, my mother's computer runs to a question mark then to the router, while mine is shown to be fine. When you click on the router within the map it brings up a page saying "Important Update. To avoid a conflict with your Internet Service Provider, your router's IP address has been updated to 10.0.0.1. You must now update the IP addresses in your router's configuration settings for each relevant service,such as port forwarding and IP address reservation." I do not know if this is the problem and it is starting to go beyond my realm of understanding. Also, possibly related, we had a bad storm that did NOT knock our power out, but the internet went down and we had to reboot the modems. This occurred right before the problems began. Last piece of information: We are going through 2 routers due to lack of jacks in the house. The line goes through the first router which connects to a second one in the back of the house. Both computers are linked to the second router, and it is the second router which shows on the network map. I go to an online college and it is necessary for me to access the printer.
View 7 Replies View Relatedis there any way i can make my canon printer i9900 wireless?
View 1 Replies View Relateddo I need USB cable connected all the time to printer and laptopto print?
View 1 Replies View RelatedI have set this "Black Friday" printer up and it shows it is transmitting wireless. However, I cannot get my PC to find it! I have tried everything I know. I am not an expert but is there something in my Verizon router that might be preventing it? I don't know what else it could be but maybe there is an expert out there that can.
View 5 Replies View RelatedI am trying to connect a Canon printer wirelessly to my system and it will not connect. What can I do to connect it?
View 1 Replies View RelatedI have a printer canon 2230 i want to canact via network cabel throw switch ,then i want to sarching printer then show workgroup and next proces is not go.
View 1 Replies View RelatedI have a Canon wireless printer, but I forget the password for conection to my laptop.What should I do?
View 1 Replies View RelatedI am sharing a canon mf4350d printer installed on a vista home premium edition computer. I am trying to access it on an imac using osx 10.6.8. Below are the steps I have taken so far:
1. On vista machine in the control panel I have checked off the "share this printer" box in the printers properties.
2. In the registry of the Vista machine I have changed the value of lmcompatibilitylevel from 3 to 1 and then rebooted.
3. On the Imac in system preferences I opened "Print and Fax" and clicked "+" to add a printer.
4. I clicked on the "IP" button and set the "Protocol" to "Line Printer Daemon - LPD"; in the "Address" field I entered the IP address of the vista machine; In the "Print Using" I set to "Generic PCL Laser Printer".
When I try and print it can't connect to the printer and it does not print.
I have a canon ipf6350 printer that I want to move to another room in my house. It is currently connected via a network cable connected directly to my wifi router. The printer does not have wifi. how can I connect the printer to the network once it is in another room? I have an older belkin n1 vision wifi router I am not using. Can I connect this wirelessly to the existing network and then plug a cat 5 cable from the belkin to the printer?
View 5 Replies View RelatedCanon lbp 2900 attached on windows 7 32 bit system,i want to shared this printer on another system(windows 7 32 bit).
View 1 Replies View RelatedI move to new house recently and found out that my new house doesn't have wireless or WiFi connection. I have Canon MP560 printer that need WIFi connection and I couldn't find out how to connect it to my computer. How to connect it to computer without using wireless connection?
View 1 Replies View RelatedThere's a Canon LBP 3500 printer on my office network.I don't know its IP.It doesn't show up when I scan the local subnet with nmap.I cannot find the manual (hardcopy or online).It is plugged into the network.It is turned on.I have turned it off and on again.I have tried plugging it into other ports on our switch.
View 1 Replies View RelatedI can't seem to get my Canon MG5220 Wireless Printer to connect to my Belkin N150 wireless router. The printer sees the belkin wireless router network name but cannot connect to it( after entering the correct security key). It worked fine with a previous wireless router. My desktop PC is connected to the belkin router via direct ethernet, and I want to be able to access my wireless printer which is located in another room from my PC. I think I remember reading that the canon mg5220 may not support WPA2 security, but Its only a year old and would prefer not to regonfigure my router's security setting. how I can get this printer to connect to my router? Any other ways to access this printer from my PC which is connected to LAN via ethernet?
View 3 Replies View RelatedI am trying to setup the wireless printer (Canon MX436) to my ACER laptop (windows 7).
I am not very techincal and the instructions say to "Press and hold the WPS button on the access point (for about 5 seconds)." but have no idea what this means.
I know the laptop has the wi-fi turned on but when the printer searches it doesn't find it.
I just bought a canon pixmaMG6120 wireless printer...hooked it up to our wireless network (via a netgear wg624v3 wireless router). pritner recognizes the network, can sign into the network and has an IP in they systems setting. i can print to it via my iphone and ipad (all on the same wireless network).my HP dv6 laptop doesnt recognize a printer is on the network though. i've tried using the included cd, tried doing it via IP address, tried taking down all the firewalls, and nothing seems to work.
View 4 Replies View RelatedI have a Canon i9900 printer wired to an XP desktop. I bought a new windows 7 laptop that connects to the internet through my wireless router. How do I setup the laptop to print through the router?
View 2 Replies View Related