Routers / Switches :: Manage Static IPS In VOIP Setup?
Jul 21, 2011
I have VOIP and was provided a modem, a Tilgen Router (Vood 452_A). I also currently have a Linksys WRT54G router. I also have a home surveillance system with a DVR that can be accessed via the net. I am trying to allow the ports to open so that traffic can navigate down to the DVR.My IPs:My VOIP has provided me with 6 static IP addresses. For sake of this issue they are:
67.xx.xxx.153, through .158My subnetmask is set to:
255.255.255.248My Settings:
The Modem is connected to world. To the modem I have the Tilgen Router connected. The Tilgen is set with an ip of .153 and the subnetmask listed above. DHCP is turned on and has IP range set for .154-.158. It is set in Bridge Mode with NAT and Firewall turned off. To that I have the WRTG54G router connected and assigned the router an Static IP of .154.. The cable is going into the Linksys WAN port.From a computer connected to a LAN port on the WRT54G, I see my public IP as .154, currently my internal IP is 192.168.1.15 so I believe I have to assign one of my Static IPs to this PC, however when I try to connect to the Linksys Router (.154) from the outside web, I am get a time out error. (also from a ping test.) My thoughts are to assign the Linksys to DHCP and use a range of .155-.158 to give each lan item a static IP. My question is will this work? Will each item in the network have its own IP and if I forward the port to the DVR that i needed, ie 80 for web client or 6100 for desktop client, will that forward through?Or do I set it to Router Mode and use the Tilgen to assign the ips.
On the Tilgen I also have an option for a DHCP relay or to turn off DHCP.
For clarification here is the setup chain
Broadband/DSL Line>>Tilgen Modem>>(LANPort1)Tilgen Router(LAN Port2)>>(WAN) Linksys(LANPort1)>>DVR/Computers
Found this walkthrough on setting the WRT54G into a Switch. If I did this, in theory the VOOD would assign those computers/dvr connected downstream via the WRT54G a static ip from my range set on the router. Then in theory I would not need to port forward port 80 since the DVR would be on its own public IP.?
how to configure QoS on my SGE2010 to support my Toshiba CIX PBX VoIP trunks. The infrastructure is straight forward: PBX(1)<==>SGE2010(1)<==>SGE2010(2)<==>SGE2010(3)<==>PBX(2) where PBX(1) and PBX(2) are connected through three SGE2010's that are trunked via fiber between buildings. I don't have VoIP handsets and the PBX's are on their own VLAN. Everything else has been a breeze in these switches but I have no experience with QoS
I am trying to Port Forward HTTP: 80, but my Router wont let me and it keep giving me this error message Status: Port Range Overlap with Remote Management.I have a NETGEAR CG814GCMR Router, I need to add that port for setting up a Game private server online, but my router wont let me, how to fix it?
I'm going to move offices into a shared situation with 3 companies. Each company will want its own private network so there's no snooping between companies. I am planning on using VOIP for the phone system (Nextiva cloud based). Is it possible to set up the system so that each company has access to the VOIP system but yet remains sequestered in the their own network for everything else. I was hoping to do this with one data port at each workstation using Cisco SPA-303 phones. The way I understand this, is that the phone plugs in to the data port and you daisy chain the workstation off from each phone. Is this possible to do this while having the system I described? Another wrinkle is that I'd also like all the networks to be access shared printers.
My adolescent son wants to create a server to host video games. We, the parents, want to separate our computers and files from all the crazy security risks my son and his friends take, while allowing them to learn by their mistakes.I want 2 separate networks, or does this make sense? Would love to have our computers (assorted PC's, Macs, both laptops and desktops, running Vista Ultimate, Windows 7, OSX 10.5 and up), ipods, TV's, Blu-rays, wireless printers, etc. isolated from our son's computers, ipods, TV's, XBox, Blurays, wireless printers, (as well as the digital stuff his friends bring over).Since security is the reason for this, would love any tips over and above Brian Posey's article on Tech Republic (5 common security mistakes people make on setting up wireless networks, or something like that)We have Optimum high speed (testing up to 65 mps) internet service and 5 static IP addresses to work with.
I am trying to setup the following. We have an RV042 Router and are using it as our gateway at the office. In the office we are using a Windows Domain abc.lan with DHCP of 10.0.0 - 10.0.0.254. The Router/Gateway is setup with a Static IP of 10.0.0.100.A couple of our office employees would like to work from home via VPN using their laptops. With the many options available for this router, I am not clear as to which options and what settings I should set.
I want to setup an home network with a wireless router and use multiple switches for wired connections through out my home. I currently have an Airport extreme hooked up to a cable modem and a leviton gateway hooked up to the Airport. The 2 computers connected to the Leviton are on a windows 7 homegroup and share fine, but won't share or discover any wireless device connected to Airport. My main goal is to have a wireless/wired network with all computers sharing information with each other. I want 2-3 wired switches/gateways with a min of 2 devices connected to each, connected to my wireless router whiich is connected to cable modem.
I got a static ip from my isp. I set up my static ip manually through my linksy router. I need the static ip to connect to a private network for my new job but cant connect to that network. I went to whatsmyip and found that my old dynamic ip is still showing up externally, it looks like my ip4 is using the dynamic as a preferred. My question is do i need to manually change the network connection on my LAN and wireless connection under ipv4 to change it from automatically obtain TO use the following address and put in my static? And do I have to change the DNS also? I am on a home network with one desktop on vista home premium and laptop windows 7.
i m using ISP provided modem+router and another D-Link Wireless router at the same time... My computer is connected to D-LInk's Router and D-Link's Router is connected to ISP's Modem...My modem's Ip address is : 192.168.1.1 Router's IP Address: 192.168.0.1ok but now problem is that now Dlink is connected to ISP's Modem and ISP's modem assigns different ip to Wl.Router. Both have DHCP enabled... But i want modem (which is also a router) to assign D-Link's router the STATIC IP... like 192.168.1.54Router Model is D-link DIR-615 Modem Model is ZTE EchoLife HG510a
This is the situation in our Lab.We have one telephone line with broadband connection and a system which is connected to a modem to use this broadband facility. Recently we have taken two static IPs over this connection for a project work.Now what I want to know is, how to configure these static IPs, so that I can connect two systems (each one to one static IP) to use these static IPs and continue to access the internet in the 3rd (already present) system.
I would like to as you that i have swiches 2960 (10Unit) and switches 3560 ( 3 unit) and router 2821 ( 1 unite) and AP( 10 unit).So do you know software can manage all those product? Like monitor switch up or down, manage configure, check performance.
At my company, we lease 3 static public IP addresses from 1 ISP. We want to have 3 separate networks that each use one of the IP addresses. Network 1 is the computer network, network 2 is the VOIP network, and network 3 is the security camera network. I am trying to determine the best way to do this. I have come up with 2 solutions in my head, but I'm not sure if they will work or not. I would like to get some input. Solution 1:Solution 1 looks something like this. Fiber box -> Router-> 3 switches. There would be one WAN input on the router, that would have a static route to 3 different LAN ports. For example, address 24.244.208.101 would be assigned to LAN port 1, 24.244.208.102 would be assigned to LAN port 2, and 24.244.208.103 would be assigned to LAN port 3 (by assigned, I mean have a static route to it). Is there some type of router that is capable of doing this? Solution 2:Solution 2 looks something like this. Fiber box -> Switch -> 3 Routers. The ethernet cable would run from the Fiber Box to a switch, and then 3 routers would be plugged into the switch. Each router would have the Static information configured in them. Would both of these methods work? If so, which would be the best way to go?
We are in the process of switching to a new internet provider in our office and have run into some problems. Our old setup was with AT&T, where they provided a managed router which linked to our internal switch and also provided NAT to the internal IP of our email server.Our new setup right now is just the internet coming in through a cable connected to a switch, we were told we needed to provide our own router. Someone donated a Cisco 2900.What should our proper set-up be? Should the internet come in directly to the router and then to our switch, or should it go to the switch they provided, then the router, and then our switch?Also, there seems to be some confusion about whether or not we need anything else to get the internet to work. There are slots for network cards in the router. Does it come with at least one built in we can use, or do we need to provide one?
I did RECOVERY on my computer. Its a Compac Windows XP Home edition. This computer runs off of my main computer by a router & adapter. My router & adaptor are showing green but the Internet is showing red. Its becuz my high speed Internat service is ATT.my.yahoo.com. which comes through IE. On my newer computer all is fine. My IE works good & all is working. but my IE on my older one which runs with the router wont set up.
I had this small internet cafe with 15 units pc. and browsing the web is not that stable. i have to unplug the internet modem everytime i can't connect to the internet.I think it has something to do with the settings that was in the router since it was just configured by a tech guy which i think not 100% sure of what he did, though it can connect to net for sometime but most of the time it is down.
Mgmt Vlan 1 (default) Data VLan 10 (with access to internet) Is there a way to have a PC attached to a SG300 switch such that it can both access Vlan 10 for data and Vlan 1 for managment ? The PC's port clearly needs to be untagged PVID on vlan 10. I have tried adding vlan 1T and setting the port as a trunk port but to no avail, The switch is currently level 2. I am guessing this might not be possible in level 2 without setting the mgmt vlan to 10 ?.
We recently moved 8 pc's from a room where they each had port on the switch to a room where there is only one port for all of them. I setup a DLINK DIR632 Router in there and they connect thru the one port thru the switch to the gateway which gets them out to the internet.The problems is I need to be able to remote desktop into these 8 PC's and I need them to be able to print to the network printer. I am using a Linksys WRT54G Broadband router as the gateway connecting the switch to the internet. The DLINK's dhcp server is on for the 8 PC's. The Linksys' dhcp server shows the DLINK as IP 192.168.1.19 on the network.I know I have to use advanced routing settings but I'm not sure about how what to make the subnet mask and IP's on both routers. I believe I need to turn off the dhcp server on the DLINK and have the Linksys' dhcp server serve all of the PC's but I'm not sure if thats the best way or if its possible.. I don't want to hack out fix only to find it breaks 3 days later.I used to do this stuff all day long in the 90's but its been a while and to me its like calculus.
I have a dell powerconnect 2848 switch and setting up a vlan 3 an make port 1 mngt, port 48 uplink to layer 3 switch and tag vlan 1 and 3 to port 48 with cli commands for this setup. and also to untag ports 2-10 for computers
I have the E3000 wired/wireless router and want to be able to manage my two SLM2008 switches with 192.168.1.253 and .254. Following the guides with adding vlan 2 and tagging the ports in which the two switches are wired together disables my ability to manage them seperately. I have added the gateway on 192.168.1.1 to both switches and told them that management vlan is 2 but no luck accessing them still.
I want to setup a static ip address for a h.264 network dvr ,however my desktop computer is out of order, that is connected direct to router,is it possible to use my wireless laptop to setup the router,or will I have to connect the eithernet cable to the laptop.
The router was working fine when it was setup but was disconnected for a short while. There is now no recognition of the router and the install cd was misplaced...
Currently in my office have a TPlink wireless router (WR1043N), and Dlink 615 router.Below is my office's network organization.Internet-->TPLinkRouter(192.168.2.0)-->DlinkRouter(192.168.0.0)We want to host a demo website but we are afraid our network being attacked. So we wish to implement a DMZ network to hide our internal network from outside. My question is can i setup a dmz network with the above capabilities by using home routers?
I have a Hawking 300N and I have misplaced my disk and I neing walked through this to have it set back up. I hooked it all up correctly and it says no internet connection
I have a Dell switch setup with 2 Vlan's. Vlan 1 is to the network. Vlan 20 is going to be for wireless access to the internet. How do I configure the switch/router so that Vlan 20 only connects to the internet and not the network? I will later want to have a 2nd SSID that I want to connect to both the internet and network.
I am following instructions I found to set up my wirelss network, but am having trouble configuring my router. I'm specifically at a standstill, because I can't connect to http://192.168.1.1. I pinged the router and got a response and went to run/ip config to confirm I have the right URL for the router, but still not able to get to the URL.
We are setting up a new office and I am trying to get RADIUS setup for authentication to my switches and routers. Currently I am working on a 3750 running IOS 15 and getting hung on what I think on something small. I have attached my Microsoft NPS Network Policy. Below is my IOS config:
aaa group server radius corp-radius server 10.15.10.20 auth-port 1812 acct-port 1813 ! aaa authentication login default group corp-radius local aaa authentication login radius-localfallback group corp-radius enable aaa authorization exec default group radius
I want to setup a voip network, there's going to be 3 switches connected to a Cisco CME router, my problem is I can't find information on how to configure it.
Today I installed the 1.0.2.6 Firmware on a RV180W. I only have now two problems regarding the Static DHCP support in the GUI.
1. Via the Networking > LAN (Local Network) > Static DHCP I have no buttons to Add a new static Lease. 2. Via the Networking > LAN (Local Network) > DHCP Lease Clients I can thick a Lease and click on Make Static IP. The result is an error: Operation failed.
