Routers / Switches :: Configure 2 Static IPs Over Single Connection?

Jan 28, 2011

This is the situation in our Lab.We have one telephone line with broadband connection and a system which is connected to a modem to use this broadband facility. Recently we have taken two static IPs over this connection for a project work.Now what I want to know is, how to configure these static IPs, so that I can connect two systems (each one to one static IP) to use these static IPs and continue to access the internet in the 3rd (already present) system.

View 7 Replies

Routers / Switches :: Multiple Gateways On A Single Router?

Feb 28, 2011

We are in the process of installing time clocks at some of our sites around the USA. Our security department has asked that the time clocks be completely isolated from the rest of the network. The time clocks will be administered by ADP via a centralized firewall utilizing NAT. We have multiple subnets available at each site. Let me give an example to calrify what I would like to do. Example: Site A has 10.168.19.0 /24 user subnet and is configured for VLAN1 using 10.168.19.1 on the router as the default gateway. I would like to use subnet 10.168.20.0 /24 for the time clocks, configure it for VLAN2 and use 10.168.20.1 as the router gateway address for VLAN2. This should allow me to NAT one of our additional public IP addresses to the 10.168.20.1 gateway address thus completely isolating the time clocks from the remainder of the network. Problem is I have not done this before so I'm a little confused about how to configure it in the Cisco 3750 switches.

View 6 Replies View Related

Cisco Routers :: Configure SRP527w Without Static Outside Ip Address

Jul 17, 2010

I need to know how to configure SRP527w without a static outside ip address to establish a VPN tunnel with VPNC3000.

View 31 Replies View Related

Routers / Switches :: Computer Is Not Showing Static Ip?

Jan 17, 2011

I got a static ip from my isp. I set up my static ip manually through my linksy router. I need the static ip to connect to a private network for my new job but cant connect to that network. I went to whatsmyip and found that my old dynamic ip is still showing up externally, it looks like my ip4 is using the dynamic as a preferred. My question is do i need to manually change the network connection on my LAN and wireless connection under ipv4 to change it from automatically obtain TO use the following address and put in my static? And do I have to change the DNS also? I am on a home network with one desktop on vista home premium and laptop windows 7.

View 5 Replies View Related

Routers / Switches :: Manage Static IPS In VOIP Setup?

Jul 21, 2011

I have VOIP and was provided a modem, a Tilgen Router (Vood 452_A). I also currently have a Linksys WRT54G router. I also have a home surveillance system with a DVR that can be accessed via the net. I am trying to allow the ports to open so that traffic can navigate down to the DVR.My IPs:My VOIP has provided me with 6 static IP addresses. For sake of this issue they are:

67.xx.xxx.153, through .158My subnetmask is set to:

255.255.255.248My Settings:

The Modem is connected to world. To the modem I have the Tilgen Router connected. The Tilgen is set with an ip of .153 and the subnetmask listed above. DHCP is turned on and has IP range set for .154-.158. It is set in Bridge Mode with NAT and Firewall turned off. To that I have the WRTG54G router connected and assigned the router an Static IP of .154.. The cable is going into the Linksys WAN port.From a computer connected to a LAN port on the WRT54G, I see my public IP as .154, currently my internal IP is 192.168.1.15 so I believe I have to assign one of my Static IPs to this PC, however when I try to connect to the Linksys Router (.154) from the outside web, I am get a time out error. (also from a ping test.) My thoughts are to assign the Linksys to DHCP and use a range of .155-.158 to give each lan item a static IP. My question is will this work? Will each item in the network have its own IP and if I forward the port to the DVR that i needed, ie 80 for web client or 6100 for desktop client, will that forward through?Or do I set it to Router Mode and use the Tilgen to assign the ips.

On the Tilgen I also have an option for a DHCP relay or to turn off DHCP.

For clarification here is the setup chain
Broadband/DSL Line>>Tilgen Modem>>(LANPort1)Tilgen Router(LAN Port2)>>(WAN) Linksys(LANPort1)>>DVR/Computers
Found this walkthrough on setting the WRT54G into a Switch. If I did this, in theory the VOOD would assign those computers/dvr connected downstream via the WRT54G a static ip from my range set on the router. Then in theory I would not need to port forward port 80 since the DVR would be on its own public IP.?

View 7 Replies View Related

Routers / Switches :: Assigning Static IP To D-Link Router?

Mar 6, 2011

i m using ISP provided modem+router and another D-Link Wireless router at the same time... My computer is connected to D-LInk's Router and D-Link's Router is connected to ISP's Modem...My modem's Ip address is : 192.168.1.1 Router's IP Address: 192.168.0.1ok but now problem is that now Dlink is connected to ISP's Modem and ISP's modem assigns different ip to Wl.Router. Both have DHCP enabled... But i want modem (which is also a router) to assign D-Link's router the STATIC IP... like 192.168.1.54Router Model is D-link DIR-615 Modem Model is ZTE EchoLife HG510a