Routers / Switches :: Configure Router For Internet Parameters?
Jun 17, 2012i am adding a wired router,during configuration i must choose between PPPoE,Dynamic,Static connection type. i have broadband cable isp
View 2 Repliesi am adding a wired router,during configuration i must choose between PPPoE,Dynamic,Static connection type. i have broadband cable isp
View 2 RepliesI configure two WIC-1DSU-T1-v2 interfaces with a T1 crossover cable. What are the mimimum configurations to do to communicate from LAN1 (int fa0/0 of one 1841 router) to LAN2 (int fa0/0 of the second 1841 router) ?
Do I need a routage protocole ? And if yes wich one ? Interne or externe (RIP or BGP) Or static route is enough ? Also, is that I should put a encapsulation, like ppp ? Is it neccessary on a point to point line ?
Finally what about the following commands, do I need it ?
service-module t1 clock source internal
service-module t1 timeslots 1-24 speed 64
service-module t1 framing esf
service-module t1 linecode b8zs
i have a pppoe connection coming through ethernet line. i.e i need to use dialer that i have created on the desktop..and i have bought a new Linksys E1000 router v2.1..now my problem is that1) After entering all the settings correctly my router worked for 3 days after that the net is not working.i.e it cannot connect to the internet keeps giving the error cannot get IP from PPPOE(i have connected my router in pppoe mode and use the router status page to connect and disconnect)I have also updated the router to the latest firmware 2.1.01 and after that the problems have started.My Net works if i directly plug the Ethernet cable in the PC.the problem starts when i connect it to my router.
View 3 Replies View RelatedI have installed a DIR615 N Router and can get onto the Internet on the PC, but when I type in the device IP address it comes up with an "error" message so I cannot configure it.
View 6 Replies View RelatedI remember long ago I was upto some trial and error with my router and I ended up in changing some ip that I didn't know about that time, now when I was trying to forward some of the ports. I addressed the computer to 192.168.1.1 (as this was my ip that time I remember and on the box its written too) but it didn't respond, then I remember that I have changed this ip to something else and now I can't remember this.
View 7 Replies View Relatedi have a ZyXel prestige 650H-31 Model # router and i'm not able to go on to configuration page of the router i tried 192.168.1.1 several times, even after system reboot and router reset, but of no use. I've a wire connection with desktop (RJ-45 port) not USB AND MY PPPoE lights never lit. originally when i entered the gateway 192.168.1.1 it asked me for username & password, since i didn't have the password at that time i tried to reset the router but after that when ever i entered 192.168.1.1 in the browser it never came up with the option to enter user name & password. I've checked all the wires are also connected. I tried prompt command and it showed that timed out thrice and then sent= 4 received= 0 lost= 100%. I had D-Link router prior to it and later connected the D-Link router an i was able to get connected to net and browse normally.
View 1 Replies View Relatedi have a LAN network between several pc's connected with several switch's and connected to Thomson SpeedTouch 510 DSL Router its ip address is 10.0.0.100 subnet 255.0.0.0 and the router dont give auto ip to the PCs i have to issign it manually to the PCs "static ip".I bought the acer android recently so i bought a tp-link td-w8901g wireless router to act as an access point so i connected the 2 routers to each other by LAN and gave the tp-link an ip address 10.0.0.12 subnet mask 255.0.0.0 so it will be the same ip range of the speedtouch and setuped the tp-link router to fit my isp configeration it worked at first but i had to reset the router so i did the same configuration i did before but didnt work and i cant access the internet using the android or the wireless but when i connect the phone to the tp-link and unplug the speedtouch the wireless works so theres no any problem with the router?
View 1 Replies View RelatedI have a Hawking 300N and I have misplaced my disk and I neing walked through this to have it set back up. I hooked it all up correctly and it says no internet connection
View 1 Replies View Relatedi am unable to configure my netgear router with my clear modem
View 1 Replies View Relatedi recently had att u vesre installed at my house with a 2 wire 3801 router/ modem but i cant get my xbox 360 online. how to configure the router for the xbox 360 so i can play xbox live.
View 1 Replies View RelatedI have one cisco 2851 router and one watchguare firewal currently being used as the main router. I want to connect the cisco as a secondary router on the same network.
View 10 Replies View RelatedI am planning to put an internet cafe in my place, i want to buy 20 units of PC to start the business. how to set-up or configure the PCs, How to use router and how to configure the PCs to activate the network.
View 4 Replies View RelatedI have a BSNL wifi modem WA3002g4 . i am unable to configure the modem192.168.1.1 site does not respond
View 1 Replies View Relatedhow to cofiger a network printer in a network, i am using a bsnl broadband connection with user id and psw. all systems are getting internet but printers are not connecting to print.
View 1 Replies View Relatedi have one machine have 2 Ethernet devices and i need to connect this server to different 2 network with 2 different gateways (192.168.2.x "vpn network" and 192.168.1.x "adsl network" )so if any other one need to connect this ftp server can connected from vpn or adsl
View 1 Replies View RelatedThis is the situation in our Lab.We have one telephone line with broadband connection and a system which is connected to a modem to use this broadband facility. Recently we have taken two static IPs over this connection for a project work.Now what I want to know is, how to configure these static IPs, so that I can connect two systems (each one to one static IP) to use these static IPs and continue to access the internet in the 3rd (already present) system.
View 7 Replies View Relatedhow do i configure cisco switch Edge
View 1 Replies View Relatedwent to change my nat type,did something wrong, reset all defaults but now my router is not connected to the internet
View 1 Replies View RelatedI have High Speed Charter Internet going to a modem in form of coaxial cable with one Ethernet port available and one coaxial connection for TV and a phone jack. I have that Ethernet port connected to a:Motorola Wireless Modem[CODE]
View 4 Replies View Relatedhow to configure VLAN on ALLIED TELESYN AT 8024M?
View 1 Replies View RelatedLost connection to Internet though router appears normal. Belkin router, MacBook.
View 1 Replies View Relatedwhy i cannot connect my internet in 50 meters away from router to computer
View 2 Replies View RelatedI'm having trouble connecting my 02 dongle to the internet using my router. My router is a TP-LINK MR3420 and my 02 modem device is E1752. I checked to see if the modem is compatible and it says it is. I went through the configuration that was given to me with the router and I tried using you tube but nothing. Do i need to get a static I.P address off my Internet provider? If I plug my 02 USB dongle directly into my computer it works perfectly and I got the router to work using a Ethernet cable and plugging it into the WAN port at the back of the router but I would prefer to let it connect through the 3g port
View 3 Replies View RelatedTrouble connecting to the internet wireless with Motorola SB6120 and Linksys WRT120N. The modem works directly with LAN but as soon as I try to use the router, I can connect to the network but no internet is available.
View 4 Replies View RelatedI have 2 linksys routers installed on my home network. The primary router is a linksys WRT360n and is stationed inside the main home, while the 2nd is a linksys WRT160N located in my office. I've connected them via the lan to lan configuration and have disabled DHCP server on the 2nd. I can access the 2nd router via my primary PC but am unable to access the internet or see the primary from the PC connected to the 2nd router.
View 3 Replies View Relatedive been having a problem with my router since ive been using it for its wireless capabilities. it is a linksys wrt120n router. our internet comes from our local cable provider and it is good internet (10Mb download speed). running to our old router that split the connection between my xbox and our desktop computer worked fine and even for a large amout of time after i switched to this wrt120n there were no internet problems. now all of a sudden the router drops connection multiple times a day which can become a hassle when i'm doing something importaant and lose connection. and just a little bit of extra information i cycle the systems every time it does it and theres no fix.
View 1 Replies View RelatedHow can I use the dual LAN of my PC to share internet with my notebook? The PC is at school where it uses a static IP and I would like to avoid buying a wireless router for this purpose.
View 3 Replies View RelatedAfter a power failure nothing could connect to the internet anymore. I called MTS (ISP provider) and they had me change some setup on my PC. Now my PC connects to the internet, but nothing else will connect (X Box, WII, iPods, Laptop). They were connected wireless before the power outage through my router. MTS said they are only responsible for ensuring their model works, not routers.I have checked some router settings. It is set for DHCP with 50 users.
View 15 Replies View RelatedI have a WN3000RP WiFi Range Extender but I cannot seem to find out how to connect to it on my Windows 7 Desktop computer to configure it. My Router is a Netgear Wireless G RouterWGR614 v9
View 7 Replies View RelatedI have an AT&T Univese which is class G. I want to run it in class N.Do you think plugging my Linksys router into the AT&T will give it to me(class n)?If so, how do I get the linksys parameters set up? It giving wrong readings at its not connecting to the internet.
View 3 Replies View RelatedI have a DI-604 D-link router, is it necessay to upgrade to newer router to get faster access to internet? Upgrade Firmware? I have a PD950 processor with Win XP pro and use it for DAYTRADING streaming data and fast executions.
View 5 Replies View RelatedI have a Netgear N300 Wireless Router (WNR2000), and I am trying to connect the internet through it. The internet light stays amber, and though the router recognizes it, I can not connect to the internet. My computer also doesn't seem to recognize the router at all. Installation CD will not work either.
View 3 Replies View Relatedi want to ask if i can link two routers while they are totally separated of each other over the internet to make a large LAN the two routers are TP link?
View 5 Replies View Related